Knoll HDP2160 Installation And User Manual

Download

Page 1

HDP2160

Installation and user manual v1.0

Page 2

— i —

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

All other product names used in this manual are the properties of their respective owners and are acknowledged.

Ver.:01

Page 3

— ii —

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector.

Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.

Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this example: “Push the Menu button on the remote control to open the Main menu.”

General Safety Information

 Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in

the unit. For servicing, contact qualified service personnel.

 Follow all warnings and cautions in this manual and on the unit case.  The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the

lens when the lamp is on.

 Do not place the unit on an unstable surface, cart, or stand.  Avoid using the system near water, in direct sunlight, or near a heating device.  Do not place heavy objects such as books or bags on the unit.

Page 4

–iii –

Projector Installation Notice

 Place the projector in a horizontal position

The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages.

 Allow at least 50 cm clearance around the exhaust vent.



 Ensure that the intake vents do not recycle hot air from the exhaust vent.  When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the air intake and exhaust vents are unobstructed.

 All enclosures should pass a certified thermal evaluation to ensure that the projector does not

recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the acceptable operation temperature range.

Minimum 500mm (19.69 inch)

Minimum 100mm (3.94 inch)

Minimum 300mm (11.81 inch)

-15°

Page 5

— iv —

Verify Installation Location

 To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper

grounding and equalized ground potential for all of the equipment in the Projector System.

 The power code provided with the Projector should be used. In case of any missing item, other

qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use 2-blade power cord.

 Verify if the voltage is stable, grounded properly and there is no electricity leakage.  Measure total power consumption which should not higher the safety capacity and avoid safety

issue and short circuit.

 Turn on Altitude Mode when located in high altitude areas  The projector can only be installed upright or inverted.  When installation the bracket, make sure the weight limit is not exceed and firmly secured.  Avoid installing near air conditioner duct or subwoofer.  Avoid installing at high temperature, insufficient cooling and heavy dust locations.  Keep your product away from fluorescent lamps to avoid malfunction

caused by IR interference

 The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal wire for achieving optimal display effect.

 The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected

to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even DAMAGE the port.

 Install the projector above 200cm to avoid damage.  The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power cord to avoid damaging the projector.

Cooling notes

Air outlet

 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.  Air outlet location should not be in front of the lens of other projector to avoid causing illusions.  Keep the outlet at least 100cm away from the inlets of other projectors

 The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After the project enters STANDBY MODE status, press the AC power button to turn off the projector and remove the power cord. DO NOT remove the power cord during the shutdown process, as it may cause damage to the projector. In the meantime, the delayed heat radiating will also affect the service life of the projector. The shutdown process may vary depending on the model used. Whatever the case may be, be sure to disconnect the power cord till after the projector enters the STANDBY status.

Air inlet

 Make sure there is no object blocking air input within 30 cm.  Keep the inlet away from other heat sources  Avoided heavy dust area

Page 6

–v –

Power Safety

 Only use the supplied power cord.  Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot traffic.

 Remove the batteries from the remote control when storing or not in use for a prolonged period.

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 34 for clear and safe instructions for this procedure. Before replacing the lamp:

 Unplug the power cord.  Allow the lamp to cool for about one hour.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury. Always keep your face away from the exhaust vent so that you do not suffer from the gas and

broken shards of the lamp.

Cleaning the Projector

 Unplug the power cord before cleaning. See Cleaning the Projector page 37.  Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on page 49.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp

specific disposal information check WWW.LAMPRECYCLE.ORG.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.

Page 7

— vi —

Main Features

 Lightweight unit, easy to pack away and transport.  Compatible with all major video standards including NTSC, PAL, and SECAM.  A high brightness rating allows for presentations in daylight or in lit rooms.  Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images.  Flexible setup allows for front, rear projections.  Line-of-vision projections remain square, with advanced keystone correction for angled projections.  Input source automatically detected.

About this Manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

Page 8

–vii –

Table of Contents

GETTING STARTED ........................................................................................................................................................... 1

PACKING CHECKLIST ........................................................................................................................................................... 1

VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2

Front-right View ............................................................................................................................................................ 2

Top view—On-screen Display (OSD) buttons and LEDs ....................................................................................... 3

Rear view ....................................................................................................................................................................... 4

Bottom view ................................................................................................................................................................... 5

REMOTE CONTROL PARTS ................................................................................................................................................... 6

REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 8

PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 8

INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 9

SETUP AND OPERATION ............................................................................................................................................... 10

STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 10

ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 12

ADJUSTING THE VERTICAL IMAGE POSITION ...................................................................................................................... 13

ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 13

ADJUSTING THE VOLUME .................................................................................................................................................. 14

ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 15

OSD MENU CONTROLS ..................................................................................................................................................... 15

Navigating the OSD ................................................................................................................................................... 15

SETTING THE OSD LANGUAGE .......................................................................................................................................... 16

OSD MENU OVERVIEW ..................................................................................................................................................... 17

PICTURE>>BASIC MENU ................................................................................................................................................. 19

PICTURE>>ADVANCED MENU ........................................................................................................................................ 20

HSG Adjustment ......................................................................................................................................................... 21

VividSettings ............................................................................................................................................................... 22

DISPLAY MENU ............................................................................................................................................................... 23

PC Detail Adjustment ................................................................................................................................................. 24

White Balance ............................................................................................................................................................. 25

User Color Temp ........................................................................................................................................................ 26

3D Setting .................................................................................................................................................................... 27

SETUP>>BASIC MENU ..................................................................................................................................................... 28

Menu Settings ............................................................................................................................................................. 29

Source .......................................................................................................................................................................... 29

SETUP>>ADVANCED MENU ............................................................................................................................................ 30

Audio ............................................................................................................................................................................ 31

Lamp ............................................................................................................................................................................ 31

Closed Caption ........................................................................................................................................................... 32

STATUS MENU ................................................................................................................................................................ 33

MAINTENANCE AND SECURITY .................................................................................................................................. 34

REPLACING THE PROJECTION LAMP ................................................................................................................................... 34

Resetting the Lamp .................................................................................................................................................... 36

CLEANING THE PROJECTOR................................................................................................................................................ 37

Cleaning the Lens ...................................................................................................................................................... 37

Cleaning the Case ...................................................................................................................................................... 37

USING THE KENSINGTON

LOCK & USING THE SECURITY BAR ......................................................................................... 38

Using the Kensington® Lock ..................................................................................................................................... 38

Using the Security Bar ............................................................................................................................................... 38

TROUBLESHOOTING ...................................................................................................................................................... 39

COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 39

TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 39

LED ERROR MESSAGES ..................................................................................................................................................... 40

IMAGE PROBLEMS .............................................................................................................................................................. 40

LAMP PROBLEMS ............................................................................................................................................................... 41

Page 9

— viii —

REMOTE CONTROL PROBLEMS .......................................................................................................................................... 41

AUDIO PROBLEMS ............................................................................................................................................................. 41

HAVING THE PROJECTOR SERVICED .................................................................................................................................. 42

HDMI Q & A .................................................................................................................................................................... 43

SPECIFICATIONS ............................................................................................................................................................. 44

SPECIFICATIONS ................................................................................................................................................................. 44

PROJECTION DISTANCE VS. PROJECTION SIZE .................................................................................................................... 45

Projection Distance and Size Table ......................................................................................................................... 45

TIMING MODE TABLE ........................................................................................................................................................ 46

PROJECTOR DIMENSIONS ................................................................................................................................................... 48

REGULATORY COMPLIANCE ....................................................................................................................................... 49

FCC WARNING .................................................................................................................................................................. 49

CANADA ............................................................................................................................................................................ 49

SAFETY CERTIFICATIONS ................................................................................................................................................... 49

APPENDIX I ........................................................................................................................................................................ 50

RS-232C PROTOCOL.......................................................................................................................................................... 50

Page 10

– 1 –

GETTING STARTED

Packing Checklist

Carefully unpack the projector and check that the following items are included:

DLP PROJECTOR WITH LENS CAP

EMOTE CONTROL

(WITH TWO AAA

ATTERIES

)

RGB C

ABLE

OWER CORD

HDMI C

ABLE

ARRYING CASE CD-ROM

(THIS USER’S MANUAL)

QUICK START GUIDE WARRANTY CARD

Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is recommend that you keep the original packing material should you ever need to return the equipment for warranty service.

Caution:

Avoid using the projector in dusty environments.

Page 11

— 2 —

Views of Projector Parts

Front-right View

ITEM LABEL DESCRIPTION SEE PAGE

IR receiver

Receive IR signal from remote control

Lens Projection Lens

Focus ring Focuses the projected image

Zoom ring Enlarges the projected image

LENS SHIFT For Image vertical shift adjustment.

Function keys

See Top view—On-screen Display (OSD) buttons and LEDs.

Important:

Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the ventilation openings.

Page 12

– 3 –

Top view—On-screen Display (OSD) buttons and LEDs

ITEM

LABEL

DESCRIPTION

SEE PAGE

Opens and exits OSD menus

Navigates and changes settings in the OSD Quick Menu – For Volume

Navigates in the OSD Quick Menu – For Keystone

ENTER

Enter or confirm highlighted OSD menu item

AUTO

Optimizes image size, position, and resolution

Navigates and changes settings in the OSD Quick Menu – For Volume

Turns the projector On or Off

POWER LED Green

Ready to power on (Standby) Lamp Lit , System stable Over Temperature

Flashing

Error code

Navigates in the OSD Quick Menu – For Keystone

10.

TEMP LED

Red

Over Temperature

11.

SOURCE

Enter the Source menu

12.

LAMP LED Red

Lamp Fail

Flashing

Error code

1 2

4 5

1012 11 79

Page 13

— 4 —

Rear view

ITEM

LABEL

DESCRIPTION

SEE PAGE

AC IN Connect the POWER cable

3D SYNC

Connect the 3D IR glasses transmitter (Note: For Vivitek brand 3D IR glasses only)

HDMI 2 Connect the HDMI cable from a HDMI device

HDMI 1 Connect the HDMI cable from a HDMI device

(USB)

Connect the USB cable from a computer

VGA IN Connect the RGB cable from a computer

RS-232C Connect RS-232 serial port cable for remote control

COMPONENT Connect the Component cable from a component device

USB POWER For USB charge support DC 5V

10.

Kensington Lock

Secure to permanent object with a Kensington® Lock system

11.

VIDEO IN Connect the COMPOSITE cable from a video device

12.

AUDIO IN (L and R) Connect the AUDIO cable from a audio device

13.

DC 12V TRIGGER

When connected to the screen through a commercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered off (see notes below).

Note:



To use this feature, you must plug in the connector before turn on/off the projector.



Screen controllers are supplied and supported by screen manufacturers.



Do not use this jack for anything other than intended use.

Warning:

As a safety precaution, disconnect all power to the projector and connecting devices before making connections.

1 2

4 5 6 7 8 9

1213

Page 14

– 5 –

Bottom view

ITEM

LABEL

DESCRIPTION

SEE PAGE

Ceiling support holes

Contact your dealer for information on mounting the projector on a ceiling

Tilt adjustor

Rotate adjuster lever to adjust angle position.

Note:

When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 6 mm (0.24 inch). The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a period of 60 seconds.

Page 15

— 6 —

Remote Control Parts

Important:

1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency

fluorescent lights can disrupt remote control operation.

2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.

3. The buttons and keys on the projector have the same functions as the corresponding buttons on the remote control. This user’s manual describes the functions based on the remote control.

Note:

Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007

Caution:

Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.

20 19

Page 16

– 7 –

ITEM

LABEL

DESCRIPTION

SEE PAGE

OFF

Turns the projector off.

Displays the PC source selection.

Video/S-Video

Displays the VIDEO source selection.

Navigates and changes settings in the OSD or MHL mode. Keystone correction.

EXIT

Goes back to previous OSD menu, exits and saves menu settings. Goes back to previous page or exit programs in MHL mode.

Enters and confirms settings in the OSD.

Navigates and changes settings in the OSD or MHL mode.

Navigates and changes settings in the OSD or MHL mode. Keystone correction.

MHL

Starts for selection in MHL mode.

10.

Laser

Presses to emit the on-screen pointer. DO NOT POINT IN EYES.

11.

Starts / pauses the file in MHL mode.

12.

Goes to the next file in MHL mode.

13.

Stops the file in MHL mode.

14.

Fast forwards the file in MHL mode.

15.

Volume

Displays the volume setting bar.

16.

Mute

Toggles the built-in speaker between on and off.

17.

Opens the 3D function OSD.

18.

Status

Opens the OSD Status menu (the menu only opens when an input device is detected).

19.

Blank

Toggles the screen between blank and normal.

20.

Freeze

Freeze/unfreezes the on-screen picture.

21.

Zoom

Displays the zoom setting bar.

22.

Lamp

Displays the lamp mode selection.

23.

Contrast

Displays the contrast setting bar.

24.

Brightness

Displays the brightness setting bar.

Page 17

— 8 —

ITEM

LABEL

DESCRIPTION

SEE PAGE

25.

Auto

Auto adjustment for frequency, phase, and position.

26.

Source

Displays the source selection bar.

27.

Fast reverses the file in MHL mode.

28.

Goes to the previous file in MHL mode.

29.

Keystone

Displays the keystone setting bar.

30.

Navigates and changes settings in the OSD or MHL mode.

31.

Opens the OSD.

32.

HDMI

Toggles the input sources for display between HDMI sources.

33.

Turns the projector on.

34.

Laser

Use as on-screen pointer. DO NOT POINT IN EYES.

Note: Controlling your smart device with the remote control

When the projector projects the contents from your MHL compatible smart device, you can use the remote control to control your smart device.

To enter the MHL mode, the following buttons are available for controlling your smart device, Arrow keys (▲Up, ▼Down, ◄ Left, ► Right), MENU/EXIT, MHL control buttons.

When the projector is under MHL mode, The keypad on projector should be with the same definition of the key on remote control.

Remote Control Operating Range

The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.

Projector and Remote Control Buttons

The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are limited in use.

Page 18

– 9 –

Inserting the Remote Control Batteries

Remove the battery compartment cover by sliding the cover in the direction of the arrow.

Insert the battery with the positive side facing up.

Replace the cover.

Caution:

1. Only use AAA batteries (Alkaline batteries are recommended).

2. Dispose of used batteries according to local ordinance regulations.

3. Remove the batteries when not using the projector for prolonged periods.

Page 19

— 10 —

SETUP AND OPERATION

Starting and Shutting down the Projector

Connect the power cord to the projector. Connect the other end to a wall outlet.

The POWER LED on the projector light.

Turn on the connected devices.

Ensure the POWER LED not a flashing. Then press the POWER

button to turn on the projector.

The projector splash screen displays and connected devices are detected.

If more than one input device is connected, press the SOURCE

button and use  to scroll among

devices. (Component is supported through the RGB to COMPONENT ADAPTER.)

 PC: Analog RGB

 HDMI 1 / HDMI 2: High-Definition Multimedia

Interface

 COMPONENT: DVD input YCbCr/ YPbPr, or HDTV

input YPbPr

 VIDEO: Traditional composite video

Page 20

– 11 –

When the “Power Off? /Press

Power again” message appears, press the POWER button. The projector turns off.

Caution:

1. Be sure to remove the lens cap before starting projector.

2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has cooled down.

Page 21

— 12 —

Adjusting the Projector Level

Take note of the following when setting up the projector:

 The projector table or stand should be level and sturdy.  Position the projector so that it is perpendicular to the screen.  Ensure the cables are in a safe location. You could trip over them.

To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired angle has been achieved.

Page 22

– 13 –

Adjusting the vertical image position

The Lens Shift function can be used to adjust the position of the vertically.

The display position can be shifted upward up to 9% and down to 5% elevation of the display.

Adjusting the Zoom, Focus and Keystone

Use the Image-zoom control (on the projector only) to resize the projected image and screen size .

Use the Image-focus control (on the projector only) to sharpen the projected image .

Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect.

The keystone control appears on the display.

Lens shift adjustable range

Shift to top

9%V

5%V

Shift range

Lens shift center position

Shift range

Page 23

— 14 —

Adjusting the Volume

Press the Volume +/- buttons on the remote control. The volume control appears on the display.

Press the MUTE button to turn off the volume. (This feature is available only on the remote).

Page 24

– 15 –

ON-SCREEN DISPLAY (OSD) MENU SETTINGS

OSD Menu Controls

The projector has an OSD that lets you make image adjustments and change various settings.

Navigating the OSD

You can use the remote control cursor buttons to navigate and make changes to the OSD.

1. To enter the OSD, press the MENU button.

2. There are six menus. Press

the cursor ◄► button to

move through the menus.

3. Press the cursor ▲▼ button to move up and down in a menu.

4. Press ◄► to change values for settings.

5. Press MENU to close the OSD or leave a submenu.

Note:

Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.

4 1

6 5

3 2

Page 25

— 16 —

Setting the OSD Language

Set the OSD language to your preference before continuing.

1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic.

2. Press the cursor ▲▼ button until Language is highlighted.

3. Press the cursor ◄► button until the language you want is selected.

4. Press the MENU button to close the OSD.

Page 26

– 17 –

OSD Menu Overview

Use the following illustration to quickly find a setting or determine the range for a setting.

Main Menu

Sub Menu

Settings

Picture >>Basic

Display Mode

Presentation, Movie, Vivid , Bright, Game, User1,3D

Brightness

0 ~ 100

Contrast

-50 ~ 50

Color

-50 ~ 50

Tint

-50 ~ 50

Sharpness

0 ~ 21

Reset Pictures Setting

Reset current display mode value

Picture >>Advanced

Color temperature

D65, D75, D83

Gamma

1.8 / 2.0 / 2.2 / 2.4 / B&W / Linear

HSG adjustment

Primary Color

R / G / B / C / M / Y

Hue

-50 ~ 50

Saturation

0 ~ 199

Gain

0 ~ 199

VividSettings

VividMotion

Off/ Low / Medium / High

VividPeaking

0 ~ 3

Flash tone

0 ~ 5

Display

Aspect Ratio

Auto / 16:9 / 4:3 / Letter Box / Real

Keystone

-40 ~ 40

Over scan

0 ~ 10

PC detail adjustment

Auto

enter

Frequency

By timing

Phase

0 ~ 100

Horizontal Position

-15 ~ 15

Vertical Position

-50 ~ 50

White Balance

Red Gain

-50 ~ 50

Green Gain

-50 ~ 50

Blue Gain

-50 ~ 50

Red Bias

-50 ~ 50

Green Bias

-50 ~ 50

Blue Bias

-50 ~ 50

User color temp

White Gain Red

5 ~ 195

White Gain Green

5 ~ 195

White Gain Blue

5 ~ 195

3D Setting

3D Mode

Auto / Side by Side / Top/Bottom / Frame Sequential / 2D to 3D

3D Sync

DLP-Link / IR-Link / Off

3D Sync Invert

Off / On

Page 27

— 18 —

Main Menu

Sub Menu

Settings

Setup >> Basic

Language

English, Français, Deutsch, Español, Português, 簡体中文, 繁體中文, Italiano,

Norsk, Svenska, Nederlands, Русский,

Polski, Suomi, Dansk, 한국어, 日本語

Projection

Front Table / Front Ceiling / Rear Table / Rear Ceiling

Auto power off

Disable / 5 / 10 / 15 / 20 / 25 / 30min

Sleep timer

Disable / 30min / 1hr / 2hr /3hr / 4hr / 8hr / 12hr

Background color

Black / Blue / Purple

Menu Setting

Menu Position

Center / Right up / Right down / Left up / Left down

Menu display time

5 / 10 / 15 / 20 / 25 / 30 sec

Source

Disable, Enable

HDMI1

Disable, Enable

HDMI2

Disable, Enable

Component

Disable, Enable

Video

Disable, Enable

Quick Auto Search

On / Off

Setup >> Advanced

Audio

Volume

0~10

Mute

Off, On

Lamp

Lamp Mode

Normal / ECO / Dynamic Eco

Reset Lamp Timer

Lamp Hour

High Altitude Mode

Off / On

Test Pattern

Off /on

Close Caption

Off / On

12V OUT A

On / Off

Reset All

Yes / No

Status

Source

Resolution

Lamp Hours (ECO, Normal)

Firmware Version

Page 28

– 19 –

PICTURE>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu. Press ◄► to change values for settings.

ITEM

DESCRIPTION

Display Mode

Press the cursor ◄► buttons to set the Display Mode.

Brightness

Press the cursor ◄► buttons to adjust the display brightness.

Contrast

Press the cursor ◄► buttons to adjust the display contrast.

Color

Press the cursor ◄► buttons to adjust the video saturation. Notes: This function is only available when Component, Video input source is

selected.

Tint

Press the cursor ◄► buttons to adjust the video tint/hue. Notes: This function is only available when Component, Video with NTSC system

input source is selected.

Sharpness

Press the cursor ◄► buttons to adjust the display sharpness. Notes: This function is only available when Component, Video input source is

selected.

Reset Picture Settings

Press the ENTER button to reset all settings to default values.

Page 29

— 20 —

PICTURE>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings.

ITEM

DESCRIPTION

Color Temperature

Press the cursor ◄► button to set the Color Temperature.

Gamma

Press the cursor ◄► button to adjust the gamma correction of the display.

HSG Adjustment

Press the ENTER button to enter the HSG Adjustment sub menu. See HSG Adjustment on page 21.

VividSettings

Press the ENTER button to enter the VividSettings sub menu. See VividSettings on page 22.

Page 30

– 21 –

HSG Adjustment

Press the ENTER button to enter the HSG Adjustment sub menu.

ITEM

DESCRIPTION

Primary Color

Press the ◄► buttons to set the Primary Color. Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized.

Hue

Press the ◄► buttons to adjust the Hue.

Saturation

Press the ◄► buttons to adjust the Saturation.

Gain

Press the ◄► buttons to adjust the Gain.

Page 31

— 22 —

VividSettings

Press the ENTER button to enter the VividSettings sub menu.

ITEM

DESCRIPTION

VividMotion

Press the ◄► buttons to select different MEMC level.

VividPeaking

Press the ◄► buttons to adjust motion adaptive sharpness enhancement (2D Peaking) value.

Flesh Tone

Press the ◄► buttons to adjust the display flesh tone.

Page 32

– 23 –

DISPLAY Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu.

Press ◄► to change values for settings.

ITEM

DESCRIPTION

Aspect Ratio

Press the cursor ◄► button to set the Aspect Ratio.

Keystone

Press the cursor ◄► button to adjust the Keystone.

Overscan

Press the cursor ◄► button to adjust the Overscan.

PC Detail Adjustment

Press the ENTER button to enter the PC Detail Adjustment sub menu. See PC Detail Adjustment on page 24.

White Balance

Press the ENTER/ ► button to enter the White Balance sub menu. See White Balance on page 25

User color temp

Press the ENTER button to enter the User Color Temp sub menu. See User Color Temp on page 26

3D Setting

Press (Enter) / ►to enter the 3D menu. See page 27 for more information on

3D Setting.

Note:

To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the 3D Disc Menu.

Page 33

— 24 —

PC Detail Adjustment

Press the ENTER button to enter the PC Detail Adjustment sub menu.

Note:

Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.

ITEM

DESCRIPTION

Auto

Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the remote control to automatically adjust frequency, phase, and position.

Frequency

Press the ◄► buttons to adjust the A/D sampling number.

Phase

Press the ◄► buttons to adjust the A/D sampling clock.

Horizontal Position

Press the ◄► buttons to adjust the display position right or left.

Vertical Position

Press the ◄► buttons to adjust the display position up or down.

Note: Some signals may take time to display or may not be displayed correctly. If the Auto Adjust operation cannot optimize the PC signal, try to adjust FREQUENCY and PHASE manually.

Page 34

– 25 –

White Balance

Press the ENTER button to enter the White Balance sub menu.

ITEM

DESCRIPTION

Red Gain

Press the ◄► buttons to adjust the Red Gain.

Green Gain

Press the ◄► buttons to adjust the Green Gain.

Blue Gain

Press the ◄► buttons to adjust the Blue Gain.

Red Bias

Press the ◄► buttons to adjust the Red Bias.

Green Bias

Press the ◄► buttons to adjust the Green Bias.

Blue Bias

Press the ◄► buttons to adjust the Blue Bias.

Page 35

— 26 —

User Color Temp

Press the ENTER button to enter the User Color Temp sub menu.

ITEM

DESCRIPTION

White Gain Red

Press the ◄► buttons to adjust the White Gain Red.

White Gain Green

Press the ◄► buttons to adjust the White Gain Green.

White Gain Blue

Press the ◄► buttons to adjust the White Gain Blue.

Page 36

– 27 –

3D Setting

ITEM

DESCRIPTION

3D Mode

Press the ◄► buttons to enter and select different 3D mode.

3D Sync

Press the ◄► buttons to enter and enable or disable 3D Sync.

3D Sync Invert

Press the ◄► buttons to enter and enable or disable 3D Sync Invert.

Note:

1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.

2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection.

3. Use 3D glasses to view a 3D image.

4. You need 3D content from a 3D DVD or 3D media file.

5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).

6. You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a driver on your PC and connect a USB emitter.

7. The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).

8. Power on the glasses. Glasses normally have a power on -off switch. Each type of glasses has their own configuration instructions. Please follow the configuration instructions that come with your glasses to finish the setup process.

Note:

Since different types of glass (DLP link or IR shutter glass) have their own setting instructions,

Please follow the guide to finish the setup process.

Page 37

— 28 —

SETUP>>Basic Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu. Press ◄► to change values for settings.

ITEM

DESCRIPTION

Language

Press the cursor ◄► buttons to select a different localization menu.

Projection

Press the cursor ◄► buttons to choose from four projection methods.

Auto Power Off

Press the cursor ◄► buttons to set the Auto Power Off timer. The projector automatically turns off if no input source is detected after the preset period of time.

Sleep Timer

Press the cursor ◄► buttons to set Sleep timer. The projector automatically turns off after the preset period of time.

Background Color

Press the cursor ◄► buttons to select the background color when no input source is

detected.

Menu Settings

Press the ENTER button to enter the Menu Settings sub menu. See Menu Settings on page 29.

Source

Press the ENTER button to enter the Source sub menu. See Source on page 29.

Page 38

– 29 –

Menu Settings

Press the ENTER button to enter the Menu Settings sub menu.

ITEM

DESCRIPTION

Menu Position

Press the ◄► buttons to select from five OSD locations.

Menu Display Time

Press the ◄► buttons to set the Menu Display timer before the OSD times out.

Source

Press the ENTER button to enter the Source sub menu.

ITEM

DESCRIPTION

Press the ◄► buttons to enable or disable the PC source.

HDMI 1

Press the ◄► buttons to enable or disable the HDMI source.

HDMI 2

Press the ◄► buttons to enable or disable the HDMI source

Component

Press the ◄► buttons to enable or disable the Component source.

Video

Press the ◄► buttons to enable or disable the Video source.

Quick Auto Search

Press the ◄► buttons to enable or disable Quick Auto Search for available input source. Notes: When the desired source is selected, the Quick Auto Search function will be turn off.

Page 39

— 30 —

SETUP>>Advanced Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu.

ITEM

DESCRIPTION

Audio

Press the ENTER button to enter the Audio sub menu. See Audio on page 31.

Lamp

Press the ENTER button to enter the Lamp sub menu. See Lamp on page 31.

High Altitude Mode

Press the cursor ◄► buttons to turn on or off High Altitude Mode. Recommended to turn on when the altitude of the environment is higher than 1500m (4921ft).

Test Pattern

Press the cursor ◄► buttons to select Test Pattern.

Closed Caption

Press the ENTER button to enter the Closed Caption sub menu. See Closed Caption on page 32.

12V OUT A

Press the cursor ◄► buttons to adjust 12V OUT.

Reset All

Press the ENTER button to enter reset all settings to default values.

Page 40

– 31 –

Audio

Press the ENTER button to enter the Audio sub menu.

ITEM

DESCRIPTION

Volume

Press the ◄► buttons to adjust the audio Volume.

Mute

Press the ◄► buttons to turn on or off the speaker.

Lamp

Press the ENTER button to enter the Lamp sub menu.

ITEM

DESCRIPTION

Lamp Mode

Press the ◄► buttons to adjust lamp brightness.

Reset Lamp Timer

Press the ENTER button to reset the Lamp Hour after the lamp is replaced.

Lamp Hour

Displays the number of hours the lamp has been in use.

Page 41

— 32 —

Closed Caption

Press the ENTER button to enter the Closed Caption sub menu.

ITEM

DESCRIPTION

Closed Caption Enable

Press the ◄► buttons to turn on or off Closed Caption. Caption Version

Press the ◄► buttons to select the Caption Version.

Page 42

– 33 –

STATUS Menu

Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu.

ITEM

DESCRIPTION

Source

Displays the activated input source.

Resolution

Displays the native resolution of input source.

Lamp Hour s (ECO, Normal)

Displays the number of hours the lamp has been in use. Firmware Version

Displays the firmware version of the projector.

Note: Status displayed in this menu is for viewing only and cannot be edited.

Page 43

— 34 —

MAINTENANCE AND SECURITY

Replacing the Projection Lamp

The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.

Important:

a. The projection lamp used in this product contains a small amount of mercury. b. Do not dispose this product with general household waste. c. Disposal of this product must be carried out in accordance with the regulations of your local

authority.

Warning:

Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.

Caution:

In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards to be discharged outward from the rear exhaust vent.

Do not inhale or do not touch glass dust or shards. Doing so could result in injury.

Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.

When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.

IF A LAMP EXPLODES

If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come out of the exhaust vent. The gas contains toxic mercury.

Open windows and doors for ventilation.

If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor immediately.

Loosen the two screws on the lamp compartment cover.

Page 44

– 35 –

Remove the lamp compartment cover.

Remove the three screws from the lamp module.

Lift the module handle up.

Pull firmly on the module handle to remove the lamp module.

Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.

Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.

Page 45

— 36 —

Resetting the Lamp

After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:

Press the MENU button to open the OSD menu.

Press the cursor ◄► button to move to the SETUP : Advanced menu. Press the cursor button to move down to Lamp and press enter.

Press the cursor ▼▲ button to move down to Reset Lamp

Timer.

Press the ◄► buttons to adjust the settings.

Press the MENU button to get back to SETUP : Advanced.

Page 46

– 37 –

Cleaning the Projector

Cleaning the projector to remove dust and grime will help ensure trouble-free operation.

Warning:

1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so

could result in a severe burn.

2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings

on the projector.

3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated

room for several hours before using.

4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.

Cleaning the Lens

You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.

1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)

2. Lightly wipe the lens in a circular motion.

Caution:

1. Do not use abrasive cleaners or solvents.

2. To prevent discoloration or fading, avoid getting cleaner on the projector case.

Cleaning the Case

Refer to the following to clean the projector case.

1. Wipe off dust with a clean dampened cloth.

2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.

3. Rinse all detergent from the cloth and wipe the projector again.

Caution:

To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.

Page 47

— 38 —

Using the Kensington® Lock & Using the Security Bar

Using the Kensington® Lock

If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.

Note:

Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any

comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-5354242, http://www.Kensington.com.

Using the Security Bar

In addition to the password protection function and the Kensington lock, the Security Bar helps protect the projector from unauthorized removal. See the following picture.

Page 48

– 39 –

TROUBLESHOOTING

Common problems and solutions

These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance.

Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.

 Use some other electrical device to confirm that the electrical outlet is working.  Ensure the projector is turned on.  Ensure all connections are securely attached.  Ensure the attached device is turned on.  Ensure a connected PC is not in suspending mode.  Ensure a connected notebook computer is configured for an external display.

(This is usually done by pressing an Fn-key combination on the notebook.)

Tips for Troubleshooting

In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more quickly.

Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.

Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.

Page 49

— 40 —

LED Error Messages

ERROR CODE MESSAGES

POWER LED

GREEN

LAMP LED

RED

TEMP LED

RED

System Initial

Flashing

OFF

Ready to Power on (Standby)

OFF

System Power on

Flashing

OFF

Lamp Lit , System stable

OFF

Cooling

Flashing

OFF

1W MCU detects scaler stops working (initial fail)

2 Flashing

OFF

Over Temperature

OFF

Thermal Break Sensor error

4 Flashing

OFF

Lamp Fail

5 Flashing

0 Flashing

OFF

Lamp Temperature shut down

5 Flashing

1 Flashing

OFF

Lamp Short circuit in output detected

5 Flashing

2 Flashing

OFF

Lamp End of lamp life detected

5 Flashing

3 Flashing

OFF

Lamp did not ignite

5 Flashing

4 Flashing

OFF

Lamp extinguished during normal operation

5 Flashing

OFF

Lamp extinguished during run-up phase

5 Flashing

6 Flashing

OFF

Lamp voltage got error

5 Flashing

7 Flashing

OFF

Lamp ballast got error

5 Flashing

8 Flashing

OFF

Lamp ballast Communication error

5 Flashing

10 Flashing

OFF

Fan-1 error

6 Flashing

1 Flashing

OFF

Fan-2 error

6 Flashing

2 Flashing

OFF

Fan-3 error

6 Flashing

3 Flashing

OFF

Case Open

7 Flashing

OFF

DAD1000 error

8 Flashing

OFF

Color wheel error

9 Flashing

OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the Power or Lamp LEDs are still blinking or any other situation that isn't listed in the chart above, please contact your service center.

Image Problems

Problem: No image appears on the screen

1. Verify the settings on your notebook or desktop PC.

2. Turn off all equipment and power up again in the correct order.

Problem: The image is blurred

1. Adjust the Focus on the projector.

2. Press the Auto button on the remote control.

3. Ensure the projector-to-screen distance is within the specified range.

4. Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

Page 50

– 41 –

1. Position the projector so it is as perpendicular to the screen as possible.

2. Use the Keystone button on the remote control to correct the problem.

Problem: The image is reversed

Check the Projection setting on the SYSTEM SETUP >> Basic > Projection menu of the OSD.

Problem: The image is streaked

1. Set the Frequency and Phase settings on the PC Detail Adjustment menu of the OSD to the default settings.

2. To ensure the problem is not caused by a connected PC’s video card, connect to another

computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the PICTURE >> Basic menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the PICTURE >> Advanced menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1. Check that the power cable is securely connected.

2. Ensure the power source is good by testing with another electrical device.

3. Restart the projector in the correct order and check that the Power LED is on.

4. If you have replaced the lamp recently, try resetting the lamp connections.

5. Replace the lamp module.

6. Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED is on, press the power button.

2. Replace the lamp module.

3. Put the old lamp back in the projector and have the projector serviced.

Remote Control Problems

Problem: The projector does not respond to the remote control

1. Direct the remote control towards remote sensor on the projector.

2. Ensure the path between remote and sensor is not obstructed.

3. Turn off any fluorescent lights in the room.

4. Check the battery polarity.

5. Replace the battery.

6. Turn off other Infrared-enabled devices in the vicinity.

7. Have the remote control serviced.

Audio Problems

Problem: There is no sound

1. Adjust the volume on the remote control.

2. Adjust the volume of the audio source.

3. Check the audio cable connection.

4. Test the source audio output with other speakers.

Page 51

— 42 —

5. Have the projector serviced.

Problem: The sound is distorted

1. Check the audio cable connection.

2. Test the source audio output with other speakers.

3. Have the projector serviced.

Having the Projector Serviced

If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The information may be useful to service personnel. For servicing, return the projector to the place you purchased it.

Page 52

– 43 –

HDMI Q & A

Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable?

Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.

˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or

up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.

˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz

or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and can successfully handle 1080p signals including those at increased color depths and/or increased refresh rates from the Source. High-Speed cables are also able to accommodate higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).

Q. How do I run HDMI cables longer than 10 meters?

There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective

distance from the typical 10 meter range to much longer lengths. These companies manufacture a variety of solutions that include active cables (active electronics built into

cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and

fiber solutions.

Q. How can I tell if a cable is an HDMI certified cable?

All HDMI products are required to be certified by the manufacturer as part of the HDMI Compliance Test Specification. However, there may be instances where cables bearing the HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively investigates these instances to ensure that the HDMI trademark is properly used in the market. We recommend that consumers buy their cables from a reputable source and a company that is trusted.

For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49

Page 53

— 44 —

SPECIFICATIONS

Specifications

Model

H1188 series

Display Type

TI DMD 0.65" 1080p

Resolution

1080p 1920x1080

Projection Distance

1.2 ~ 10 m

Projection Screen Size

25.9" ~ 324.97"

Projection Lens

Manual Focus/Manual Zoom

Zoom Ratio

1.5x with lens shift

Vertical Keystone Correction

+/- 40 Degree

Projection Methods

Front, Rear, Desktop/Ceiling (Rear, Front)

Data Compatibility

VGA, SVGA, XGA, WXGA, SXGA, SXGA+, UXGA, WUXGA, Mac

Sdtv/Edtv/ Hdtv

480i, 480p, 576i, 576p, 720p, 1080i, 1080p

Video Compatibility

NTSC, PAL, SECAM

H-Sync

2D: 15, 30~91.4KHz / 3D: 101.6KHz

V-Sync

24~30Hz, 47~120Hz

Safety Certification

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CU, NOM

Operation Temperature

5° ~ 35°C

Dimensions

286.3 mm (W) x 272.2 mm (D) x 128.1 mm (H)

Ac Input

AC Universal 100-240V

Power Consumption

350W (Normal), 290W (ECO), <0.5W (Standby)

Lamp

260W (Normal) / 205W (ECO)

Audio Speaker

10W mono speaker

Input Terminals

VGA x 1

Component (YPbPr RCAx3) x 1

Composite x 1

HDMI x 2

RCA Stereo Audio LR x 1

Control Terminals

RS-232C

3D sync

Screen trigger: DC Jack x 1 (DC12V 200mA output function)

USB (Type mini B) - service only

USB (type A) support DC 5V

Security

Kensington lock / Security Bar

Note: For questions regarding product specifications, please contact your local distributor.

HDP2160b

Page 54

– 45 –

Projection Distance vs. Projection Size

Projection Distance and Size Table

H1188

IMAGE

DIAGONAL

IMAGE WIDTH IMAGE HEIGHT

PROJECTION

DISTANCE

FROM

PROJECTION

DISTANCE

OFFSET-A

(INCH) (INCH) (CM) (INCH) (CM) (INCH) (CM) (INCH) (CM) (MM)

52.3

132.8

29.4

74.7

72.7

184.6

109.3

277.6

112.1

61.0

155.0

34.3

87.2

84.8

215.4

127.5

323.9

130.8

62.8

159.4

35.3

89.7

87.2

221.6

131.2

333.1

134.5

69.7

177.1

39.2

99.6

96.9

246.2

145.7

370.1

149.4

73.2

186.0

41.2

104.6

101.8

258.5

153.0

388.7

156.9

78.4

199.2

44.1

112.1

109.0

276.9

163.9

416.4

168.1

83.7

212.5

47.1

119.5

116.3

295.4

174.9

444.2

179.3

100

87.2

221.4

49.0

124.5

121.1

307.7

182.2

462.7

186.8

120

104.6

265.7

58.8

149.4

145.4

369.3

218.6

555.2

224.1

135

117.7

298.9

66.2

168.1

163.6

415.4

245.9

624.6

252.2

150

130.7

332.1

73.5

186.8

181.7

461.6

273.2

694.0

280.2

200

174.3

442.8

98.1

249.1

242.3

615.4

364.3

925.4

373.6

HDP2160b

Page 55

— 46 —

Timing Mode Table

SIGNAL

RESOLUTION

H-SYNC

( KHZ )

V-SYNC

( HZ )

COMPOSITE

S_VIDEO

COMPONENT

RGB

(ANALOG)

HDMI

(DIGITAL)

NTSC － 15.734

60 ○ －－－

PAL/SECAM

－

15.625

50 ○ －－－

VESA

640 x 400

37.9

85.08 －－ ○ ○

720 x 400

31.5

70.1 －－ ○ ○

720 x 400

37.9

85.04 －－ ○ ○

640 x 480

31.5

60 －－ ○ ○

640 x 480

37.9

72.8 －－ ○ ○

640 x 480

37.5

75 －－ ○ ○

640 x 480

43.3

85 －－ ○ ○

800 x 600

35.2

56.3 －－ ○ ○

800 x 600

37.9

60.3 －－ ○ ○

800 x 600

46.9

75 －－ ○ ○

800 x 600

48.1

72.2 －－ ○ ○

800 x 600

53.7

85.1 －－ ○ ○

800 x 600

76.3

120 －－ ○ ○

1024 x 576

35.8

60 －－ ○ ○

1024 x 600

37.3

60 －－ ○ ○

1024 x 600

41.5

65 －－ ○ ○

1024 x 768

48.4

60 －－ ○ ○

1024 x 768

56.5

70.1 －－ ○ ○

1024 x 768

75 －－ ○ ○

1024 x 768

68.7

85 －－ ○ ○

1024 x 768

97.6

120 －－ ○ ○

1024 x 768

120 －－ ○ ○

1152 x 864

67.5

75 －－ ○ ○

1280 x 720

60 －－ ○ ○

1280 x 720

120 －－ ○ ○

1280 x 768

47.4

60 －－ ○ ○

1280 x 768

47.8

59.9 －－ ○ ○

1280 x 800

49.7

59.8 －－ ○ ○

1280 x 800

62.8

74.9 －－ ○ ○

1280 x 800

71.6

84.9 －－ ○ ○

1280 x 800

101.6

119.9 －－ ○ ○

1280 x 1024

60 －－ ○ ○

1280 x 1024

75 －－ ○ ○

1280 x 1024

91.1

85 －－ ○ ○

Page 56

– 47 –

SIGNAL

RESOLUTION

H-SYNC

( KHZ )

V-SYNC

( HZ )

COMPOSITE

S_VIDEO

COMPONENT

RGB

(ANALOG)

HDMI

(DIGITAL)

1280 x 960

60 －－ ○ ○

1280 x 960

85.9

85 －－ ○ ○

1360 x 768

47.7

60 －－ ○ ○

1400 x 1050

65.3

60 －－ ○ ○

1440 x 900

55.5

59.9 －－ ○ ○

1440 x 900

55.9

59.9 －－ ○ ○

1440 x 900

70.6

75 －－ ○ ○

1600 x1200

60 －－ ○ ○

1680 x 1050

64.7

59.9 －－ ○ ○

1680 x 1050

65.3

60 －－ ○ ○

1920 x 1200

60 －－ ○ ○

1920 x 1080

67.5

60 －－ ○ ○

Apple Macintosh

640 x 480

66.7 －－ ○ ○

832 x 624

49.7

74.5 －－ ○ ○

1024 x 768

60.2

74.9 －－ ○ ○

1152 x 870

68.7

75.1 －－ ○ ○

SDTV

480i

15.734

60 － ○ － ○

576i

15.625

50 － ○ － ○

EDTV

576p

31.3

50 － ○ － ○

480p

31.5

60 － ○ － ○

HDTV

720p

37.5

50 － ○ － ○

720p

60 － ○ － ○

1080i

33.8

60 － ○ － ○

1080i

28.1

50 － ○ － ○

1080p

24 － ○ － ○

1080p

25 － ○ － ○

1080p

33.7

30 － ○ － ○

1080p

56.3

50 － ○ － ○

1080p

67.5

60 － ○ － ○

O：Frequency supported —：Frequency not supported

The native resolution of the panel is 1920x1080

Resolution others than native resolution may be display with uneven size of text or line

The color of mean Displayable only. (4:3 only) The color of mean may have a little noise is acceptable HDTV timing main check tool is DVD player, VG828 is secondary

Page 57

— 48 —

Projector Dimensions

Page 58

– 49 –

REGULATORY COMPLIANCE

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by the parties responsible for compliance could void the user’s authority to operate the equipment.

Canada

This class B digital apparatus complies with Canadian ICES-003.

Safety Certifications

FCC-B, cUL, UL, CE, C-tick, CCC, KC, CU, NOM

Page 59

— 50 —

APPENDIX I

RS-232C Protocol

RS232 Setting

Baud rate:

9600

Parity check:

None

Data bit:

Stop bit:

Flow Control

None

Minimum delay for next command: 1ms

Control Command Structure

Header code

Command code

Data code

End code

HEX

Command

Data

0Dh

ASCII

‘V’

Command

Data

Operation Command

Note: "CR" mean Carriage Return XX=00-98, projector's ID, XX=99 is for all projectors Return Result P=Pass / F=Fail n: 0:Disable/1: Enable/Value(0~9999)

Command Group 00

ASCII

HEX

Function

Description

Return Result

VXXS0001

56h Xh Xh 53h 30h 30h 30h 31h 0Dh

Power On

P/F

VXXS0002

56h Xh Xh 53h 30h 30h 30h 32h 0Dh

Power Off

P/F

VXXS0003

56h Xh Xh 53h 30h 30h 30h 33h 0Dh

Resync

P/F

VXXG0004

56h Xh Xh 47h 30h 30h 30h 34h 0Dh

Get Lamp Hours

Pn/F

VXXS0005n

56h Xh Xh 53h 30h 30h 30h 35h nh 0Dh

Set Air filter timer

n=0~999999

P/F

VXXG0005

56h Xh Xh 47h 30h 30h 30h 35h 0Dh

Get Air filter timer

n=0~999999

Pn/F

VXXS0006

56h Xh Xh 53h 30h 30h 30h 36h 0Dh

System Reset

P/F

VXXG0007

56h Xh Xh 47h 30h 30h 30h 37h 0Dh

Get System Status

0: Reset 1:Standby 2:Operation 3:Cooling

Pn/F VXXG0008

56h Xh Xh 47h 30h 30h 30h 38h 0Dh

Get F/W Version

Pn/F

VXXG0009

56h Xh Xh 47h 30h 30h 30h 39h 0Dh

Get Alter EMail

Pn/F

VXXS0009n

56h Xh Xh 53h 30h 30h 30h 39h nh 0Dh

Set Alter Email

n=xxxxxx@xxxx.x xx.xx

P/F

Page 60

– 51 –

Command Group 01

ASCII

HEX

Function

Description

Return Value

VXXG0101

56h Xh Xh 47h 30h 31h 30h 31h 0Dh

Get Brightness

n=0~100

Pn/F

VXXS0101n

56h Xh Xh 53h 30h 31h 30h 31h nh 0Dh

Set Brightness

n=0~100

P/F

VXXG0102

56h Xh Xh 47h 30h 31h 30h 32h 0Dh

Get Contrast

n=0~100

Pn/F

VXXS0102n

56h Xh Xh 53h 30h 31h 30h 32h nh 0Dh

Set Contrast

n=0~100

P/F

VXXG0103

56h Xh Xh 47h 30h 31h 30h 33h 0Dh

Get Color

n=0~100

Pn/F

VXXS0103n

56h Xh Xh 53h 30h 31h 30h 33h nh 0Dh

Set Color

n=0~100

P/F

VXXG0104

56h Xh Xh 47h 30h 31h 30h 34h 0Dh

Get Tint

n=0~100

Pn/F

VXXS0104n

56h Xh Xh 53h 30h 31h 30h 34h nh 0Dh

Set Tint

n=0~100

P/F

VXXG0105

56h Xh Xh 47h 30h 31h 30h 35h 0Dh

Get Sharpness

0~31

Pn/F

VXXS0105n

56h Xh Xh 53h 30h 31h 30h 35h nh 0Dh

Set Sharpness

0~31

P/F

VXXG0106

56h Xh Xh 47h 30h 31h 30h 36h 0Dh

Get Color Temperature

0:Warm 1:Normal 2:Cold

Pn/F

VXXS0106n

56h Xh Xh 53h 30h 31h 30h 36h nh 0Dh

Set Color Temperature

0:Warm 1:Normal 2:Cold

P/F

VXXG0107

56h Xh Xh 47h 30h 31h 30h 37h 0Dh

Get Gamma

0:1.8 1:2.0C 2:2.2 3:2.4 4:B&W 5:Linear

Pn/F

VXXS0107n

56h Xh Xh 53h 30h 31h 30h 37h nh 0Dh

Set Gamma

0:1.8 1:2.0C 2:2.2 3:2.4 4:B&W 5:Linear

P/F

VXXG0108

56h Xh Xh 47h 30h 31h 30h 38h 0Dh

Get Display Mode

0: Presentation 1:Bright 2:Game 3:Movie 4:TV 5:sRGB 6:BlackBoard 7:User

Pn/F

VXXS0108n

56h Xh Xh 53h 30h 31h 30h 38h nh 0Dh

Set Display Mode

0: Presentation 1:Bright 2:Game 3:Movie 4:TV 5:sRGB 6:BlackBoard 7:User

P/F

Command Group 02

ASCII

HEX

Function

Description

Return Value

VXXS0201

56h Xh Xh 53h 30h 32h 30h 31h 0Dh

Select RGB

P/F

VXXS0202

56h Xh Xh 53h 30h 32h 30h 32h 0Dh

Select RGB2

P/F

VXXS0203

56h Xh Xh 53h 30h 32h 30h 33h 0Dh

Select DVI

P/F

VXXS0204

56h Xh Xh 53h 30h 32h 30h 34h 0Dh

Select Video

P/F

Page 61

— 52 —

Command Group 02

ASCII

HEX

Function

Description

Return Value

VXXS0205

56h Xh Xh 53h 30h 32h 30h 35h 0Dh

Select S-Video

P/F

VXXS0206

56h Xh Xh 53h 30h 32h 30h 36h 0Dh

Select HDMI

P/F

VXXS0207

56h Xh Xh 53h 30h 32h 30h 37h 0Dh

Select BNC

P/F

VXXS0208

56h Xh Xh 53h 30h 32h 30h 38h 0Dh

Select Component

P/F

VXXS0209

56h Xh Xh 53h 30h 32h 30h 39h 0Dh

Select HDMI 2(MEDIA)

P/F

VXXS0210

56h Xh Xh 53h 30h 32h 31h 30h 0Dh

Select HDMI 3

P/F

VXXG0220

56h Xh Xh 47h 30h 32h 32h 30h 0Dh

Get Current Source

Return 1:RGB 2:RGB2 3:DVI 4:Video 5:S-Video 6:HDMI 7:BNC 8:Component 9:HDMI 2(MEDIA) 10:HDMI 3

Pn/F

Command Group 03

ASCII

HEX

Function

Description

Return Value

VXXG0301

56h Xh Xh 47h 30h 33h 30h 31h 0Dh

Get Scaling

0: Fill 1: 4:3 2: 16:9 3: Letter Box 4: Native 5: 2.35:1

Pn/F

VXXS0301n

56h Xh Xh 53h 30h 33h 30h 31h nh 0Dh

Set Scaling

0: Fill 1: 4:3 2: 16:9 3: Letter Box 4: Native 5: 2.35:1

P/F

VXXG0302

56h Xh Xh 47h 30h 33h 30h 32h 0Dh

Blank

Pn/F

VXXS0302n

56h Xh Xh 53h 30h 33h 30h 32h nh 0Dh

Blank

P/F

VXXG0303

56h Xh Xh 47h 30h 33h 30h 33h 0Dh

Auto Keystone On

Pn/F

VXXS0303n

56h Xh Xh 53h 30h 33h 30h 33h nh 0Dh

Auto Keystone On

P/F

VXXG0304

56h Xh Xh 47h 30h 33h 30h 34h 0Dh

Freeze On

Pn/F

VXXS0304n

56h Xh Xh 53h 30h 33h 30h 34h nh 0Dh

Freeze On

P/F

VXXG0305

56h Xh Xh 47h 30h 33h 30h 35h 0Dh

Volume

n=0~30

Pn/F

VXXS0305n

56h Xh Xh 53h 30h 33h 30h 35h nh 0Dh

Volume

n=0~30

P/F

VXXG0306

56h Xh Xh 47h 30h 33h 30h 36h 0Dh

Treble

n=0~16

Pn/F

VXXS0306n

56h Xh Xh 53h 30h 33h 30h 36h nh 0Dh

Treble

n=0~16

P/F

VXXG0307

56h Xh Xh 47h 30h 33h 30h 37h 0Dh

Bass

n=0~16

Pn/F

VXXS0307n

56h Xh Xh 53h 30h 33h 30h 37h nh 0Dh

Bass

n=0~16

P/F

VXXG0308

56h Xh Xh 47h 30h 33h 30h 38h 0Dh

Projection Mode

0:Front 1:Rear 2: Ceiling 3: Rear+Ceiling

Pn/F

Page 62

– 53 –

Command Group 03

ASCII

HEX

Function

Description

Return Value

VXXS0308n

56h Xh Xh 53h 30h 33h 30h 38h nh 0Dh

Projection Mode

0:Front 1:Rear 2: Ceiling 3: Rear+Ceiling

P/F

VXXG0309

56h Xh Xh 47h 30h 33h 30h 39h 0Dh

Set vertical keystone value

n=-40~+40

Pn/F

VXXS0309n

56h Xh Xh 53h 30h 33h 30h 39h nh 0Dh

Set vertical keystone value

n=-40~+40

P/F

VXXG0310

56h Xh Xh 47h 30h 33h 31h 30h 0Dh

Set horizontal keystone value

n=-20~+20

Pn/F

VXXS0310n

56h Xh Xh 53h 30h 33h 31h 30h nh 0Dh

Set horizontal keystone value

n=-20~+20

P/F

VXXG0311

56h Xh Xh 47h 30h 33h 31h 31h 0Dh

Adjust the zoom

n=-10~+10

Pn/F

VXXS0311n

56h Xh Xh 53h 30h 33h 31h 31h nh 0Dh

Adjust the zoom

n=-10~+10

P/F

VXXG0312

56h Xh Xh 47h 30h 33h 31h 32h 0Dh

Adjust the focus

n=-20~+20

Pn/F

VXXS0312n

56h Xh Xh 53h 30h 33h 31h 32h nh 0Dh

Adjust the focus

n=-20~+20

P/F

VXXG0313

56h Xh Xh 47h 30h 33h 31h 33h 0Dh

Adjust the vertical lens shift

n=-20~+20

Pn/F

VXXS0313n

56h Xh Xh 53h 30h 33h 31h 33h nh 0Dh

Adjust the vertical lens shift

n=-20~+20

P/F

VXXG0314

56h Xh Xh 47h 30h 33h 31h 34h 0Dh

Adjust the horizontal lens shift

n=-20~+20

Pn/F

VXXS0314n

56h Xh Xh 53h 30h 33h 31h 34h nh 0Dh

Adjust the horizontal lens shift

n=-20~+20

P/F

VXXG0315

56h Xh Xh 47h 30h 33h 31h 35h 0Dh

Adjust the 3D Mode

n= 0~2

Pn/F

VXXS0315n

56h Xh Xh 53h 30h 33h 31h 35h nh 0Dh

Adjust the 3D Mode

0:Off 1:DLP 2: IR

P/F

VXXG0316

56h Xh Xh 47h 30h 33h 31h 36h 0Dh

Adjust the 3D sync inverter

n= 0~1

Pn/F

VXXS0316n

56h Xh Xh 53h 30h 33h 31h 36h nh 0Dh

Adjust the 3D sync inverter

0:Off 1:On

P/F

VXXG0317

56h Xh Xh 53h 30h 33h 31h 37h 0Dh

Adjust the 3D format

n= 0~3

P/F

VXXS0317n

56h Xh Xh 47h 30h 33h 31h 37h nh 0Dh

Adjust the 3D format

0:FS 1:TB 2:SBS 3:FP

Pn/F

VXXG0319

56h Xh Xh 47h 30h 33h 31h 39h 0Dh

Adjust the Lamp mode

n= 0~2

Pn/F

VXXS0319n

56h Xh Xh 53h 30h 33h 31h 39h nh 0Dh

Adjust the Lamp mode

0:Eco 1:Normal 2:Dynamic

P/F

VXXG0322

56h Xh Xh 47h 30h 33h 32h 32h 0Dh

Get Fan Speed

n= 0~1

Pn/F

VXXS0322n

56h Xh Xh 53h 30h 33h 32h 32h nh 0Dh

Set Fan Speed

0:Normal 1:High Speed

P/F

VXXG0331

56h Xh Xh 47h 30h 33h 33h 31h 0Dh

Get the R gain

n= 0~200

Pn/F

VXXS0331n

56h Xh Xh 53h 30h 33h 33h 31h nh 0Dh

Set the R gain

n= 0~200

P/F

VXXG0332

56h Xh Xh 47h 30h 33h 33h 32h 0Dh

Get the G gain

n= 0~200

Pn/F

VXXS0332n

56h Xh Xh 53h 30h 33h 33h 32h nh 0Dh

Set the G gain

n= 0~200

P/F

VXXG0333

56h Xh Xh 47h 30h 33h 33h 33h 0Dh

Get the B gain

n= 0~200

Pn/F

VXXS0333n

56h Xh Xh 53h 30h 33h 33h 33h nh 0Dh

Set the B gain

n= 0~200

P/F

Page 63

— 54 —

Command Group 03

ASCII

HEX

Function

Description

Return Value

VXXG0334

56h Xh Xh 53h 30h 33h 31h 37h 0Dh

Get the R offset

n= -100~100

P/F

VXXS0334n

56h Xh Xh 47h 30h 33h 31h 37h nh 0Dh

Set the R offset

n= -100~100

Pn/F

VXXG0335

56h Xh Xh 47h 30h 33h 31h 39h 0Dh

Get the G offset

n= -100~100

Pn/F

VXXS0335n

56h Xh Xh 53h 30h 33h 31h 39h nh 0Dh

Set the G offset

n= -100~100

P/F

VXXG0336

56h Xh Xh 47h 30h 33h 32h 32h 0Dh

Get the B offset

n= -100~100

Pn/F

VXXS0336n

56h Xh Xh 53h 30h 33h 32h 32h nh 0Dh

Set the B offset

n= -100~100

P/F

VXXG0337

56h Xh Xh 47h 30h 33h 33h 37h 0Dh

Get the white R gain

n= 0~100

Pn/F

VXXS0337n

56h Xh Xh 53h 30h 33h 33h 37h nh 0Dh

Set the white R gain

n= 0~100

P/F

VXXG0338

56h Xh Xh 47h 30h 33h 33h 38h 0Dh

Get the white G gain

n= 0~200

Pn/F

VXXS0338n

56h Xh Xh 53h 30h 33h 33h 38h nh 0Dh

Set the white G gain

n= 0~200

P/F

VXXG0339

56h Xh Xh 47h 30h 33h 33h 39h 0Dh

Get the white B gain

n= 0~200

Pn/F

VXXS0339n

56h Xh Xh 53h 30h 33h 33h 39h nh 0Dh

Set the white B gain

n= 0~200

P/F

VXXG0340

56h Xh Xh 53h 30h 33h 34h 30h 0Dh

Get the Red Hue

n= -100~100

P/F

VXXS0340n

56h Xh Xh 47h 30h 33h 34h 30h nh 0Dh

Set the Red Hue

n= -100~100

Pn/F

VXXG0341

56h Xh Xh 47h 30h 33h 34h 31h 0Dh

Get the Red Saturation

n= -100~100

Pn/F

VXXS0341n

56h Xh Xh 53h 30h 33h 34h 31h nh 0Dh

Set the Red Saturation

n= -100~100

P/F

VXXG0342

56h Xh Xh 47h 30h 33h 34h 32h 0Dh

Get the Red Gain

n= -100~100

Pn/F

VXXS0342n

56h Xh Xh 53h 30h 33h 34h 32h nh 0Dh

Set the Red Gain

n= -100~100

P/F

VXXG0343

56h Xh Xh 53h 30h 33h 34h 33h 0Dh

Get the Green Hue

n= -100~100

P/F

VXXS0343n

56h Xh Xh 47h 30h 33h 34h 33h nh 0Dh

Set the Green Hue

n= -100~100

Pn/F

VXXG0344

56h Xh Xh 47h 30h 33h 34h 34h 0Dh

Get the Green Saturation

n= -100~100

Pn/F

VXXS0344n

56h Xh Xh 53h 30h 33h 34h 34h nh 0Dh

Set the Green Saturation

n= -100~100

P/F

VXXG0345

56h Xh Xh 47h 30h 33h 34h 35h 0Dh

Get the Green Gain

n= -100~100

Pn/F

VXXS0345n

56h Xh Xh 53h 30h 33h 34h 35h nh 0Dh

Set the Green Gain

n= -100~100

P/F

VXXG0346

56h Xh Xh 53h 30h 33h 34h 36h 0Dh

Get the Blue Hue

n= -100~100

P/F

VXXS0346n

56h Xh Xh 47h 30h 33h 34h 36h nh 0Dh

Set the Blue Hue

n= -100~100

Pn/F

VXXG0347

56h Xh Xh 47h 30h 33h 34h 37h 0Dh

Get the Blue Saturation

n= -100~100

Pn/F

VXXS0347n

56h Xh Xh 53h 30h 33h 34h 37h nh 0Dh

Set the Blue Saturation

n= -100~100

P/F

VXXG0348

56h Xh Xh 47h 30h 33h 34h 38h 0Dh

Get the Blue Gain

n= -100~100

Pn/F

VXXS0348n

56h Xh Xh 53h 30h 33h 34h 38h nh 0Dh

Set the Blue Gain

n= -100~100

P/F

VXXG0349

56h Xh Xh 53h 30h 33h 34h 39h 0Dh

Get the Cyan Hue

n= -100~100

P/F

VXXS0349n

56h Xh Xh 47h 30h 33h 34h 39h nh 0Dh

Set the Cyan Hue

n= -100~100

Pn/F

VXXG0350

56h Xh Xh 47h 30h 33h 35h 30h 0Dh

Get the Cyan Saturation

n= -100~100

Pn/F

VXXS0350n

56h Xh Xh 53h 30h 33h 35h 30h nh 0Dh

Set the Cyan Saturation

n= -100~100

P/F

VXXG0351

56h Xh Xh 47h 30h 33h 35h 31h 0Dh

Get the Cyan Gain

n= -100~100

Pn/F

VXXS0351n

56h Xh Xh 53h 30h 33h 35h 31h nh 0Dh

Set the Cyan Gain

n= -100~100

P/F

VXXG0352

56h Xh Xh 53h 30h 33h 35h 32h 0Dh

Get the Magenta Hue

n= -100~100

P/F

VXXS0352n

56h Xh Xh 47h 30h 33h 35h 32h nh 0Dh

Set the Magenta Hue

n= -100~100

Pn/F

Page 64

– 55 –

Command Group 03

ASCII HEX Function Description Return Value

VXXG0353 56h Xh Xh 47h 30h 33h 35h 33h 0Dh

Get the Magenta Saturation

n= -100~100 Pn/F

VXXS0353n 56h Xh Xh 53h 30h 33h 35h 33h nh 0Dh

Set the Magenta Saturation

n= -100~100 P/F

VXXG0354 56h Xh Xh 47h 30h 33h 35h 34h 0Dh

Get the Magenta Gain

n= -100~100 Pn/F

VXXS0354n 56h Xh Xh 53h 30h 33h 35h 34h nh 0Dh Set the Magenta Gain n= -100~100 P/F

VXXG0355 56h Xh Xh 53h 30h 33h 35h 35h 0Dh Get the Yellow Hue n= -100~100 P/F

VXXS0355n 56h Xh Xh 47h 30h 33h 35h 35h nh 0Dh Set the Yellow Hue n= -100~100 Pn/F

VXXG0356 56h Xh Xh 47h 30h 33h 35h 36h 0Dh

Get the Yellow Saturation

n= -100~100 Pn/F

VXXS0356n 56h Xh Xh 53h 30h 33h 35h 36h nh 0Dh

Set the Yellow Saturation

n= -100~100 P/F

VXXG0357 56h Xh Xh 47h 30h 33h 35h 37h 0Dh Get the Yellow Gain n= -100~100 Pn/F

VXXS0357n 56h Xh Xh 53h 30h 33h 35h 37h nh 0Dh Set the Yellow Gain n= -100~100 P/F

VXXG0358 56h Xh Xh 47h 30h 33h 35h 38h 0Dh Get IR On/Off Status n= 0~3 Pn/F

VXXS0358n 56h Xh Xh 53h 30h 33h 35h 38h nh 0Dh Get IR On/Off Status

0:Both on

1:Front on 2:Back on

3:Both off

P/F

Knoll Systems

145 Tyee Drive Point Roberts, WA 98281 USA 14-7163 Vantage Way, Delta BC V4G 1N1 Canada