Page 1
PROJECTOR
User’s Manual
HDP2100 High Definition Projector
Page 2
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2010
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
— i —
Page 3
HDP2100 Users Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the MENU button on the remote control to open the DISPLAY menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
— ii —
Page 4
Projector Installation Notice
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
Allow at least 50 cm clearance around the exhaust vent.
Preface
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 – 35°C while the projector is running, and the air intake and
exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable 5 – 35°C range.
Power Safety
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
– iii –
Page 5
HDP2100 Users Manual
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 30
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Cleaning the Projector
Unplug the power cord before cleaning. See Cleaning the Projector on page 32.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
on page 43.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG
specific disposal information check WWW.LAMPRECYCLE.ORG.
. For lamp
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
Main Features
• Lightweight unit, easy to pack away and transport.
• Compatible with all major video standards including NTSC, PAL, and SECAM.
• A high brightness rating allows for presentations in daylight or in lit rooms.
• Supports resolutions up to SXGA+ at 16.7 million colors to deliver crisp, clear images.
• Flexible setup allows for front, rear projections.
• Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
• Input source automatically detected.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
— iv —
Page 6
Preface
Table of Contents
GETTING STARTED.......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS............................................................................................................................................... 2
HDP2100 Front-right View ............................................................................................................................................ 2
Top view—On-screen Display (OSD) buttons and LEDs ............................................................................................... 3
Rear view ........................................................................................................................................................................ 4
Bottom view..................................................................................................................................................................... 5
REMOTE CONTROL PARTS ................................................................................................................................................... 6
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 8
PROJECTOR AND REMOTE CONTROL BUTTONS.................................................................................................................... 8
SETUP AND OPERATION................................................................................................................................................. 9
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 9
CONNECTING INPUT DEVICES ............................................................................................................................................ 10
STARTING AND SHUTTING DOWN THE PROJECTOR............................................................................................................. 11
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 13
ADJUSTING THE ZOOM RING, FOCUS AND KEYSTONE ........................................................................................................ 14
ADJUSTING THE VOLUME .................................................................................................................................................. 15
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 16
OSD MENU CONTROLS ..................................................................................................................................................... 16
Navigating the OSD ...................................................................................................................................................... 16
SETTING THE OSD LANGUAGE.......................................................................................................................................... 17
OSD MENU OVERVIEW ..................................................................................................................................................... 18
PICTURE: BASIC MENU................................................................................................................................................... 19 U
PICTURE: ADVANCED MENU .......................................................................................................................................... 20 U
HSG Adjustment............................................................................................................................................................ 21
DISPLAY MENU............................................................................................................................................................... 22
PC Detail Adjustment.................................................................................................................................................... 23
SYSTEM SETUP: BASIC MENU....................................................................................................................................... 24 U
Menu Settings................................................................................................................................................................ 25
Source ........................................................................................................................................................................... 25
SYSTEM SETUP: ADVANCED MENU .............................................................................................................................. 26
Audio............................................................................................................................................................................. 27
Lamp ............................................................................................................................................................................. 27
HDMI............................................................................................................................................................................ 28
Closed Caption.............................................................................................................................................................. 28
INFORMATION MENU ................................................................................................................................................... 29
MAINTENANCE AND SECURITY................................................................................................................................. 30
REPLACING THE PROJECTION LAMP................................................................................................................................... 30
CLEANING THE PROJECTOR................................................................................................................................................ 32
Cleaning the Lens ......................................................................................................................................................... 32
Cleaning the Case......................................................................................................................................................... 32
USING THE KENSINGTON
TROUBLESHOOTING ..................................................................................................................................................... 34
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 34
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 34
LED ERROR MESSAGES .................................................................................................................................................... 35
IMAGE PROBLEMS.............................................................................................................................................................. 35
LAMP PROBLEMS ............................................................................................................................................................... 36
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 36
AUDIO PROBLEMS ............................................................................................................................................................. 37
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 37
SPECIFICATIONS............................................................................................................................................................. 38
SPECIFICATIONS................................................................................................................................................................. 38
®
LOCK ....................................................................................................................................... 33
– v –
Page 7
HDP2100 Users Manual
PROJECTION DISTANCE VS. PROJECTION SIZE ................................................................................................................... 39
HDP2100 Series Projection Distance and Size Table .................................................................................................. 39
HDP2100 SERIES TIMING MODE TABLE ...........................................................................................................................40
PROJECTOR DIMENSIONS ................................................................................................................................................... 42
REGULATORY COMPLIANCE ..................................................................................................................................... 43
FCC WARNING.................................................................................................................................................................. 43
CANADA ............................................................................................................................................................................ 43
SAFETY CERTIFICATIONS ................................................................................................................................................... 43
EN 55022 WARNING ......................................................................................................................................................... 43
— vi —
Page 8
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
HDP2100 SERIES DLP PROJECTOR
HDP2100 Users Manual
R
EMOTE CONTROL
(WITH TWO AA BATTERIES)
CABLE CARRYING CASE CD-ROM
HDMI
VGA CABLE COMPONENT CABLE POWER CORD
HIS USER’S MANUAL)
(T
W
ARRANTY CARD
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
– 1 –
Page 9
HDP2100 Users Manual
r
Views of Projector Parts
HDP2100 Series Front-right View
ITEM LABEL DESCRIPTION SEE PAGE:
1.
Height-adjuster button Push to release height adjuster
13
2.
3.
4.
5.
Height adjuster Adjusts level of projector
Lens Projection Lens
IR receiver Receive IR signal from remote control
Focus ring Focuses the projected image
6
14
6.
7.
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
Zoom ring Enlarges the projected image
Function keys
See Top view—On-screen Display (OSD) buttons
and LEDs.
3
– 2 –
Page 10
Top view—On-screen Display (OSD) buttons and LEDs
HDP2100 Users Manual
r
ITEM LABEL DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
(Power button)
BLANK Displays a blank screen and mutes audio
◄ (Left cursor) /
Volume-
Enter Enter or confirm highlighted OSD menu item
MENU Opens and exits OSD menus
▲ (Up cursor) /
Keystone+
AUTO Optimizes image size, position, and resolution
► (Right cursor) /
Volume+
SOURCE Enter the Source menu
Turns the projector On or Off.
Navigates and changes settings in the OSD
Quick Menu – For Volume
Navigates and changes settings in the OSD
Quick Menu – For Keystone
Navigates and changes settings in the OSD
Quick Menu – For Volume
SEE
PAGE:
11
16
16
10
10.
11.
12.
▼ (Down cursor) /
Keystone-
READY LED
TEMP LED Flashing Error code
Navigates and changes settings in the OSD
Quick Menu – For Keystone
Red Lamp is ready to be powered-on.
Flashing
Lamp is not ready (warming up/shutting down/cooling)
(see LED Error Messages on page 35)
– 3 –
16
Page 11
HDP2100 Users Manual
Rear view
ITEM LABEL DESCRIPTION SEE PAGE:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
AC IN Connect the POWER CABLE
(USB)
COMPONENT IN Connect a component video enabled device
S-VIDEO IN Connect the S-VIDEO CABLE from a video device
VIDEO IN Connect the COMPOSITE CABLE from a video device
VGA IN
HDMI – 1 Connect the HDMI CABLE from a HDMI device
HDMI – 2 Connect the HDMI CABLE from a HDMI device
DC 12V Connect the 12V OUT
Kensington Lock
Speaker Outputs audio sound
IR receiver Receive IR signal from remote control
AUDIO IN (L and R) Connect the AUDIO CABLES from a audio device
Connect the USB CABLE from a computer
Connect the RGB CABLE from a computer and
components
Secure to permanent object with a Kensington® Lock
system
11
10
33
10
6
14.
AUDIO IN Connect an AUDIO CABLE from the input device
10
15.
16.
Note:
If your video equipment has various input sources, it is recommended to connect in priority of
HDMI, component (thru VGA), S-Video, Composite for better picture quality.
RS-232C Connect RS-232 serial port cable for remote control
AUDIO OUT Connect an AUDIO CABLE for audio loop through
– 4 –
Page 12
Bottom view
HDP2100 Users Manual
ITEM LABEL DESCRIPTION SEE PAGE:
1.
2.
3.
4.
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
Tilt adjustor Rotate adjuster lever to adjust angle position.
Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling
Height adjustor Adjuster drops down when adjuster button is pushed.
Height adjustor button Push to release adjustor.
13
13
– 5 –
Page 13
HDP2100 Users Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
– 6 –
Page 14
HDP2100 Users Manual
ITEM LABEL DESCRIPTION SEE PAGE:
1.
2.
3.
4.
5.
Power OFF Turns the projector off
HDMI 2 Displays the HDMI 2 source selection
S-VIDEO Displays the S-VIDEO source selection
VIDEO Displays the VIDEO source selection
Up cursor /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
11
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
ENTER Enters and confirms settings in the OSD
Right cursor
Down cursor
ASPECT RATIO Displays the ASPECT RATIO selections
SOURCE Detects the input device
STATUS
BRIGHT Displays the brightness setting bar
SHARP Displays the sharpness setting bar
COLOR Displays the color setting bar
TINT Displays the tint setting bar
BLANK Makes the screen blank
FREEZE Freezes/unfreezes the on-screen picture
AUTO Auto adjustment for frequency, phase, and position
LIGHT
Navigates and changes settings in the OSD
Opens the OSD Status menu
(the menu only opens when an input device is detected)
Turns on or off the remote control backlight for about 10 seconds. Pressing any
other key while the backlight is on keeps the backlight on for a further 10 seconds.
16
16
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
VOL -
Adjusts volume
VOL +
MUTE Mutes the built-in speaker
CONTRAST Displays the contrast settings bar
PICTURE MODE Changes the Display Mode setting
MENU/ EXIT Opens and exits the OSD
Left cursor Navigates and changes settings in the OSD
COMP Displays the Component source selection
PC Displays the PC source selection
HDMI 1 Displays the HDMI 1 source selection
Power ON Turns the projector on
IR transmitter Transmits signals to projector
– 7 –
16
16
11
Page 15
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are limited in use.
– 8 –
Page 16
Inserting the Remote Control Batteries
Remove the battery compartment cover
1.
by sliding the cover in the direction of
the arrow.
Insert the battery with the positive side
2.
facing up.
S
ETUP AND OPERATION
Replace the cover.
3.
Caution:
1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
— 9 —
Page 17
HDP2100 Users Manual
Connecting Input Devices
A PC or notebook computer and video devices can be connected to the projector at the same time. Video
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
ITEM LABEL DESCRIPTION
(USB)
COMPONENT IN Connect a component video enabled device
S-VIDEO IN Connect the S-VIDEO cable from a video device
VIDEO IN Connect the COMPOSITE cable from a video device
VGA IN Connect the RGB cable from a computer and components
HDMI – 1
HDMI – 2
DC 12V Connect the 12V OUT
AUDIO IN (L and R) Connect the AUDIO cables from a audio device
AUDIO IN Connect an AUDIO cable from the input device
Connect the USB cable from a computer
Connect the HDMI cable from a HDMI device
RS-232C Connect RS-232 serial port cable for remote control
AUDIO OUT Connect an AUDIO cable for audio loop through
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 10 –
Page 18
Starting and Shutting down the Projector
Connect the power cord to the projector.
1.
Connect the other end to a wall outlet.
The
POWER LED will be on.
D
D
D
L
P
P
r
o
j
e
c
t
o
r
–
U
s
e
r
’
s
M
a
n
u
a
l
L
P
P
r
o
j
e
c
t
o
r
–
U
s
e
r
’
s
L
P
P
r
o
j
e
c
t
o
r
–
U
M
s
e
r
’
s
M
a
n
u
a
l
a
n
u
a
l
Turn on the connected devices.
2.
3.
Ensure the POWER LED displays a
solid blue and not a flashing blue. Then
press the
the projector.
The projector splash screen displays and
connected devices are detected.
If more than one input device is con-
4.
nected, press the SOURCE button and
use ▲▼ to scroll among devices.
(Component is supported through the
RGB to COMPONENT ADAPTER.)
POWER button to turn on
• PC: Analog RGB
• HDMI 1/2: High Definition Multimedia Interface
Component: DVD input YCbCr / YPbPr, or HDTV
•
input YPbPr via HD15 connector
S-Video: Super video (Y/C separated)
•
Video: Traditional composite video
•
– 11 –
Page 19
HDP2100 Users Manual
When the POWER OFF window ap-
5.
pears, press
on the remote control. The projec-
tor turns off.
Caution:
Do not unplug the power cord until the READY LED stops flashing–indicating the projector has
cooled down.
on the control panel or
– 12 –
Page 20
Adjusting the Projector Level
Take note of the following when setting up the projector:
• The projector table or stand should be level and sturdy.
• Position the projector so that it is perpendicular to the screen.
• Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection
angle.
• Ensure the cables are in a safe location. You could trip over them.
HDP2100 Users Manual
1.
2.
3.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B].
The height adjuster drops down [C].
To lower the level of the projector, press the height-adjuster button and push down
on the top of the projector.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the
desired angle has been achieved.
– 13 –
Page 21
HDP2100 Users Manual
Adjusting the Zoom ring, Focus and Keystone
Use the Image-zoom
1.
control (on the projector
only) to resize the projected image and screen
B
size
Use the Image-focus
2.
control (on the projector
only) to sharpen the projected image
Use the KEYSTONE
3.
buttons (on the projector
or the remote control) to
correct image-trapezoid
(wider top or bottom)
effect.
.
A
.
The keystone control
4.
appears on the display.
Remote control and OSD panel
– 14 –
Page 22
Adjusting the Volume
Press the Volume +/-
1.
buttons on the remote
control.
The volume control
appears on the display.
Press the Left or Right
2.
Cursor buttons on the
keypad to adjust Volume
+/-.
HDP2100 Users Manual
Press the MUTE button to
3.
turn off the volume (This
feature is available only
on the remote).
– 15 –
Page 23
HDP2100 Users Manual
ON-S
CREEN DISPLAY
(OSD) M
ENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the
projector.
1. To enter the OSD, press the MENU
button.
2. There are six menus. Press the cursor ◄► button to move through the
menus.
3. Press the cursor ▲▼ button to move
up and down in a menu.
4. Press ◄► to change values for set-
tings.
5. Press MENU to close the OSD or
leave a sub menu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the PC Detail
Adjustment item in the PICTURE: Basic menu can only be modified when connected to a PC.
Items that are not available cannot be accessed and are grayed out.
— 16 —
Page 24
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ◄► button to navigate to SYSTEM SETUP: Basic.
HDP2100 Users Manual
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is selected.
4. Press the MENU button to close the OSD.
– 17 –
Page 25
HDP2100 Users Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
– 18 –
Page 26
HDP2100 Users Manual
PICTURE: Basic Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
PICTURE: Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Basic
menu. Press ◄► to change values for settings.
Note:
Customizeing the settings in PICTURE: Basic menu is only available in User 1/ 2/ 3 mode.
ITEM DESCRIPTION
Press the cursor ◄► buttons to set the Display Mode.
Display Mode
User Mode
Brightness Press the cursor ◄► buttons to adjust the display brightness.
Contrast Press the cursor ◄► buttons to adjust the display contrast.
Color
Tint
Sharpness
Flesh Tone
(Range: Movie/ Bright/ Normal/ User 1/ User 2/ User 3)
Notes: ISF Day/ISF Night is available when ISF Mode is on.
Press the cursor ◄► buttons to set the User Mode.
(Range: Movie/ Bright/ Normal)
Press the cursor ◄► buttons to adjust the video saturation.
Notes: This function is only available when Component, Video or S-Video input source is
selected.
Press the cursor ◄► buttons to adjust the video tint/hue.
Notes: This function is only available when Component, Video or S-Video with NTSC
system input source is selected.
Press the cursor ◄► buttons to adjust the display sharpness.
Notes: This function is only available when Component, Video or S-Video input source is
selected.
Press the cursor ◄► buttons to adjust the display flesh tone.
Notes: This function is only available when Component, Video or S-Video input source is
selected.
Save Setting Press the ENTER button to save all settings.
Reset Picture Settings Press the ENTER button to reset all settings to default values.
– 19 –
Page 27
HDP2100 Users Manual
PICTURE: Advanced Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
PICTURE: Advanced menu. Press the cursor ▲▼ button to move up and down in the
PICTURE: Advanced menu. Press ◄► to change values for settings.
ITEM DESCRIPTION
Noise Reduction Press the cursor ◄► button to adjust the Noise Reduction.
Color Temperature Press the cursor ◄► button to set the Color Temperature.
Gamma
HSG Adjustment
Color Space
Press the cursor ◄► button to adjust the gamma correction of the display.
Notes: This function is only available in User 1/ 2/ 3 mode.
Press the ENTER button to enter the HSG Adjustment sub menu.
See HSG Adjustment on page 21.
Press the cursor ◄► button to set the Color Space.
(Range: Auto/ RGB/ SDTV/ HDTV)
Notes: This function is only available when HDMI input source is selected.
– 20 –
Page 28
HSG Adjustment
Press the ENTER button to enter the HSG Adjustment sub menu.
ITEM DESCRIPTION
HDP2100 Users Manual
Primary Color
Hue Press the ◄► buttons to adjust the Hue.
Saturation Press the ◄► buttons to adjust the Saturation.
Gain Press the ◄► buttons to adjust the Gain.
Press the ◄► buttons to set the Primary Color.
Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized.
– 21 –
Page 29
HDP2100 Users Manual
DISPLAY Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu.
Press ◄► to change values for settings.
ITEM DESCRIPTION
Aspect Ratio
Keystone
Overscan Press the cursor ◄► button to adjust the Overscan.
PC Detail Adjustment
Auto Keystone
Press the cursor ◄► button to set the Aspect Ratio.
(Range: Auto/ 16:9/ 4:3/ Letter Box/ Real)
Press the cursor ◄► button to adjust the Keystone.
Notes: This function is available when the Auto keystone function is turned off.
Press the ENTER button to enter the PC Detail Adjustment sub menu.
See PC Detail Adjustment on page 23.
Press the cursor ◄► button to turn on or off the Auto Keystone.
Notes: When Auto Keystone is on, the projector will automatically adjust the Keystone.
– 22 –
Page 30
HDP2100 Users Manual
PC Detail Adjustment
Press the ENTER button to enter the PC Detail Adjustment sub menu.
Note:
Customizing the settings in PC Detail Adjustment menu is only available when PC input source
(analog RGB) is selected.
ITEM DESCRIPTION
Auto
Frequency Press the ◄► buttons to adjust the A/D sampling number.
Phase Press the ◄► buttons to adjust the A/D sampling clock.
Horizontal Position Press the ◄► buttons to adjust the display position right or left.
Vertical Position Press the ◄► buttons to adjust the display position up or down.
Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the
remote control to automatically adjust frequency, phase, and position.
– 23 –
Page 31
HDP2100 Users Manual
SYSTEM SETUP: Basic Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
SYSTEM SETUP: Basic menu. Press the cursor ▲▼ button to move up and down in the
SYSTEM SETUP: Basic menu. Press ◄► to change values for settings.
ITEM DESCRIPTION
Press the cursor ◄► buttons to select a different localization menu.
Language
Splash Logo
Projection
Blank Timer
Auto Power Off
Sleep Timer
Background Color
(Range: English/ Danish/ Dutch/ Finnish/ French/ German/ Italian/ Japanese/ Korea/
Norwegian/ Polish/ Portuguese/ Russian/ Traditional Chinese/ Simplified Chinese/
Spanish/ Swedish)
Press the cursor ◄► buttons to select a different startup screen.
(Range: Vivitek/ Blue/ Black)
Press the cursor ◄► buttons to choose from four projection methods:
Front Table/ Front Ceiling/ Rear Table/ Rear Ceiling.
Press the cursor ◄► buttons to set the Blank Screen timer. The projected image is automatically restored after the set time.
(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Press the cursor ◄► buttons to set the Auto Power Off timer. The projector automatically
turns off if no input source is detected after the preset period of time.
(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Press the cursor ◄► buttons to set Sleep timer. The projector automatically turns off after the
preset period of time.
(Range: Disable/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr)
Press the cursor ◄► buttons to select the background color when no input source is detected.
(Range: Purple/ Black/ Blue)
Menu Settings Press the ENTER button to enter the Menu Settings sub menu. See Menu Settings on page 25.
Source Press the ENTER button to enter the Source sub menu. See Source on page 25.
– 24 –
Page 32
Menu Settings
Press the ENTER button to enter the Menu Settings sub menu.
ITEM DESCRIPTION
HDP2100 Users Manual
Menu Position
Menu Display Time
Press the ◄► buttons to select from five OSD locations:
Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right.
Press the ◄► buttons to set the Menu Display timer before the OSD times out.
(Range: 5sec/ 10sec/ 15sec/ 20sec/ 25sec/ 30sec)
Source
Press the ENTER button to enter the Source sub menu.
ITEM DESCRIPTION
PC Press the ◄► buttons to enable or disable the PC source.
HDMI 1
HDMI 2
Component Press the ◄► buttons to enable or disable the Component source.
Video Press the ◄► buttons to enable or disable the Video source.
S-Video Press the ◄► buttons to enable or disable the S-Video source.
Quick Auto Search
Press the ◄► buttons to enable or disable the HDMI source.
Press the ◄► buttons to enable or disable Quick Auto Search for available input source.
Notes: When the desired source is selected, the Quick Auto Search function will be turn off.
– 25 –
Page 33
HDP2100 Users Manual
SYSTEM SETUP: Advanced Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
SYSTEM SETUP: Advanced menu. Press the cursor ▲▼ button to move up and down in the
SYSTEM SETUP: Advanced menu.
ITEM DESCRIPTION
Audio Press the ENTER button to enter the Audio sub menu. See Audio on page 27.
Lamp Press the ENTER button to enter the Lamp sub menu. See Lamp on page 27.
HDMI Press the ENTER button to enter the HDMI sub menu. See HDMI on page 28.
High Altitude Mode
Test Pattern Press the cursor ◄► buttons to turn on or off the grid test pattern.
Closed Caption
LED Control
Reset All Press the ENTER button to enter reset all settings to default values.
Press the cursor ◄► buttons to turn on or off High Altitude Mode when the altitude of the
environment is higher than 1500m, or the temperature is over 40°C.
Press the ENTER button to enter the Closed Caption sub menu.
See Closed Caption on page 28.
Press the cursor ◄► buttons to select the LED control.
Select Normal for normal LED display and Off to disable LED display.
– 26 –
Page 34
Audio
Press the ENTER button to enter the Audio sub menu.
ITEM DESCRIPTION
Volume Press the ◄► buttons to adjust the audio Volume.
Bass Press the ◄► buttons to adjust the audio Bass.
Treble Press the ◄► buttons to adjust the audio Treble.
HDP2100 Users Manual
Mute Press the ◄► buttons to turn on or off the speaker.
AGC Press the ◄► buttons to turn on or off the AGC setting.
Reset Press the ENTER button to reset all settings to default values.
Lamp
Press the ENTER button to enter the Lamp sub menu.
ITEM DESCRIPTION
Lamp Mode Press the ◄► buttons to adjust lamp brightness.
Reset Lamp Timer Press the ENTER button to reset the Lamp Hour after the lamp is replaced.
Lamp Hour Displays the number of hours the lamp has been in use.
– 27 –
Page 35
HDP2100 Users Manual
HDMI
Press the ENTER button to enter the HDMI sub menu.
ITEM DESCRIPTION
HDMI Format
HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain.
Press the ◄► buttons to select from three HDMI display formats:
Auto/ PC signal/ Video signal.
Closed Caption
Press the ENTER button to enter the Closed Caption sub menu.
ITEM DESCRIPTION
Closed Caption Enable Press the ◄► buttons to turn on or off Closed Caption.
Caption Version Press the ◄► buttons to select the Caption Version.
– 28 –
Page 36
HDP2100 Users Manual
INFORMATION Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
INFORMATION Menu.
ITEM DESCRIPTION
Source Displays the activated input source.
Resolution Displays the native resolution of input source.
Lamp Hour Displays the number of hours the lamp has been in use.
Firmware Version Displays the firmware version of the projector.
Note:
Information displayed in this menu is for viewing only and cannot be edited.
– 29 –
Page 37
HDP2100 Users Manual
M
AINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
Remove the single screw on
1.
the lamp compartment cover.
Remove the lamp compart-
2.
ment cover.
— 30 —
Page 38
Remove the three screws from
3.
the lamp module.
Lift the module handle up.
4.
Pull firmly on the module
5.
handle to remove the lamp
module.
HDP2100 Users Manual
Reverse steps 1 to 5 to install
6.
the new lamp module.
While installing, align the
lamp module with the
connector and ensure it is level
to avoid damage.
Note: The lamp module must
sit securely in place and the
lamp connector must be connected properly before
tightening the screws.
– 31 –
Page 39
HDP2100 Users Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the
lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then
wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
– 32 –
Page 40
HDP2100 Users Manual
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,
http://www.Kensington.com.
– 33 –
Page 41
HDP2100 Users Manual
T
ROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
• Use some other electrical device to confirm that the electrical outlet is working.
• Ensure the projector is turned on.
• Ensure all connections are securely attached.
• Ensure the attached device is turned on.
• Ensure a connected PC is not in suspending mode.
• Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing a Fn-key combination on the notebook).
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
— 34 —
Page 42
LED Error Messages
HDP2100 Users Manual
ERROR CODE MESSAGES
Lamp Ready ON ON OFF
Start ON OFF OFF
Cooling ON FLASHING OFF
Over temperature OFF OFF ON
Thermal Break Sensor error 4 4 OFF
Lamp End of lamp life detected 5 3 OFF
Burner Fan error 6 1 OFF
Lamp Fan error 6 2 OFF
Power Fan error 6 3 OFF
DMD Fan error 6 4 OFF
Case Open 7 OFF OFF
DMD error 8 OFF OFF
Color wheel error 9 OFF OFF
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact
your service center.
POWER LED
BLINK
READY LED
BLINK
TEMP LED
BLINK
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Installation I menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
– 35 –
Page 43
HDP2100 Users Manual
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the READY LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
– 36 –
Page 44
HDP2100 Users Manual
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
– 37 –
Page 45
HDP2100 Users Manual
Specifications
S
PECIFICATIONS
Model
Display type
Native Resolution
Weight
Projection distance
Projection screen size
Projection lens
Zoom ratio
Vertical keystone correction
Auto Keystone
Projection methods
Data compatibility
SDTV/ EDTV/ HDTV
Video compatibility
H-Sync
V-Sync
Safety certification
480i, 576i, 576p, 480p, 720p, 1080i, 1080p
FCC-B, UL, cUL, CB, CE, CCC, KC, PCT, and C-tick
Front, Rear, Desktop/Ceiling (Rear, Front)
NTSC 4.43, PAL (M/N/60), SECAM
TI DLP DMD 0.65”
1 meters ~ 10 meters
Manual Focus/Manual Zoom
VGA, SVGA, XGA, SXGA, Mac
HDP2100 Series
1920 x 1080
3.4 kg (7.5 lbs)
25" ~ 300"
1.2
+/- 15 degrees
Yes
15.6 – 91.1 kHz
50 – 85 Hz
Operation temperature
Dimensions
AC Input
Power consumption
Stand By
Lamp
Audio speaker
Input Terminals
Output Terminals
Control Terminals
5° ~ 35°C
332.8 mm (W) x 113 mm (H) x 254.6 mm (D)
AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/
Standard mode: 250W (Typical)/ 270W (Maximum)
Boost mode: 300W (Typical)/ 320W (Maximum)
<1 watt
230W
AMP 5W speaker
Digital: HDMI x 2
Analog: RGB HD-15 x 1
Composite: RCA x 1 (Yellow)
S-Video: mini dim x 1
Component: RCA x 3
Audio in:
DC_out (screen trigger): DC Jack x 1 (DC12V 200mA output function)
ψ3.5 mm stereo mini jack x 1; RCA x 2 R/L
Mini-jack stereo x 1
RS-232: DSUB-9 x 1
±
10%
Security
Keyboard Emulation Control: USB connector type B
Kensington lock
— 38 —
Page 46
Projection Distance vs. Projection Size
HDP2100 Series Projection Distance and Size Table
16:9 SCREEN PROJECTION DISTANCE
DIAGONAL WIDTH HEIGHT
INCH CM CM CM
MIN
LENGTH
(WITH MAX
ZOOM)
AVERAGE
HDP2100 Users Manual
VERTICAL
MAX
LENGTH
(WITH MIN
ZOOM)
OFFSET IN
CM
30 76 66 37 106 116 127 11
40 102 89 50 141 155 169 15
50 127 111 62 176 194 211 19
60 152 133 75 211 232 253 22
80 203 177 100 282 310 338 30
100 254 221 125 352 387 422 37
120 305 266 149 422 465 507 45
150 381 332 187 528 581 634 56
200 508 443 249 704 774 845 75
220 559 487 274 774 852 929 82
250 635 553 311 880 968 1056 93
300 762 664 374 1056 1162 1267 112
– 39 –
Page 47
HDP2100 Users Manual
HDP2100 Series Timing Mode Table
The projector can display several resolutions. The following table outlines the resolutions that can be
displayed by the projector.
SIGNAL RESOLUTION
NTSC — 15.734 60.0 O
PAL/SECAM — 15.625 50.0 O
720 x 400 37.9 85.0 — — O O
640 x 480 31.5 60.0 — — O O
640 x 480 37.9 72.8 — — O O
640 x 480 37.5 75.0 — — O O
640 x 480 43.3 85.0 — — O O
800 x 600 35.2 56.3 — — O O
800 x 600 37.9 60.3 — — O O
800 x 600 46.9 75.0 — — O O
800 x 600 48.1 72.2 — — O O
800 x 600 53.7 85.1 — — O O
1024 x 768 48.4 60.0 — — O O
VESA
Apple
Macintosh
SDTV
EDTV
1024 x 768 56.5 70.1 — — O O
1024 x 768 60.0 75.0 — — O O
1024 x 768 68.7 85.0 — — O O
1280 x 800 49.7 59.8 — — O O
1280 x 800 62.8 74.9 — — O O
1280 x 800 71.6 84.8 — — O O
1280 x 1024 64.0 60.0 — — O O
1280 x 1024 80.0 75.0 — — O O
1280 x 1024 91.1 85.0 — — O O
1400 x 1050 65.3 60.0 — — O O
1440 x 900 55.9 60.0 — — O O
1600 x1200 75.0 60 — — O O
640 x 480 35.0 66.7 — — O O
832 x 624 49.7 74.5 — — O O
1024 x 768 60.2 74.9 — — O O
1152 x 870 68.7 75.1 — — O O
480i 15.734 60.0 — O — O
576i 15.625 50.0 — O — O
576p 31.3 50.0 — O — O
480p 31.5 60.0 — O — O
H-SYNC
(KHZ)
V-SYNC
(HZ)
COMPOSITE
/ S-VIDEO
COMPONENT
—
—
RGB
(ANALOG)
－ －
－ －
HDMI
(DIGITAL)
– 40 –
Page 48
HDP2100 Users Manual
SIGNAL RESOLUTION
720p 37.5 50.0 — O — O
720p 45.0 60.0 — O — O
1080i 33.8 60.0 — O — O
HDTV
1080i 28.1 50.0 — O — O
1080p 67.5 60.0 — O — O
1080p 56.3 50.0 — O — O
O: Frequency supported
—: Frequency not supported
The native resolution of the panel for the HDP2100 series is 1920 x 1080.
Resolution other than native resolution may display with uneven size of text or lines.
H-SYNC
(KHZ)
V-SYNC
(HZ)
COMPOSITE
/ S-VIDEO
COMPONENT
RGB
(ANALOG)
HDMI
(DIGITAL)
– 41 –
Page 49
HDP2100 Users Manual
Projector Dimensions
– 42 –
Page 50
R
EGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, UL, cUL, CB, CE, CCC, KC, PCT, and C-tick
EN 55022 Warning
This is a Class B product. In a domestic environment, it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room, meeting room, or auditorium.
— 43 —
Loading...