Knoll HDMIDA2, HDMIDA8, HSMIDA4 User Manual 2

Specifications:

Models and Dimensions

HDMIDA2 one input two outputs

2.5” w x 3/4” h x 2-3/8” deep (6.3 x 1.9 x 6 cm)

HSMIDA4 one input and four outputs

6.5” w x 1” h x 3-1/4” deep (16.5 x 2.5 x 8.3 cm)

HDMIDA8 one input and eight outputs
12-5/8 w x 1.75” h x 4-1/8” deep (32 x 4.5 x 10.6 cm)

Power:
5 VDC 2000 mA.

Warranty

Knoll Systems warrants its products sold in the USA and Canada by authorized
Knoll dealers to be free of defects in materials and workmanship. This warranty
extends for three full years from the date of purchase by the original consumer.
Any products returned to Knoll Systems and found to be defective by Knoll
Systems within the warranty period will be repaired or replaced at Knoll Systems
option, at no charge. Knoll Systems will not be responsible for the actual cost of
installation or removal of the product, nor for any incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This
warranty gives you specific legal rights. You may have additional legal rights
that vary from state to state.

Knoll Systems www.knollsystems.com

145 Tyee Drive Point Roberts, WA 98281

15-7163 Vantage Way, Delta Bc V4G 1N1

Tel. [phone], fax [phone]

Made in China Knoll Systems All Rights Reserved

HDMIDA4
FOUR OUTPUT
DISTRIBUTION
AMPLIFIER

Installation Instructions v1.2

Warning: To be installed and/or used in accordance with

appropriate electrical codes and regulations. If you are not sure
about any part of these instructions, consult a qualified
electrician.

Introduction: Thank you for your purchase of a Knoll HDMI
distribution amplifier. This DA will take any HDMI signal and
distribute it to up to 4 outputs. Up to 4 HDMIDA8’s (8 output
distribution amps) can be plugged into one HDMIDA4 giving as
many as 32 outputs. Knoll HDMI distribution amplifiers can be
cascaded twice for up to 512 outputs from 73 HDMIDA8’s.

The maximum wire length for HDMI cables is about 15 meters
or 50 feet. If longer wire runs are needed so the Knoll HDMI
balun solutions to allow wire runs up to 35 meters or 120 feet.

Features:

 Newest version is 8 bit 3D capable with wider

bandwidth.

 Tabletop box design.
 Will safely send 480i/p, 720p and 1080i/p signals.
 Easy to use. Installs in seconds and there are no user

adjustments.

 Can be cascaded two times to give a maximum of 512

HDMI outputs

 Supports all HDCP forms.

 Power supply included.

Wiring:
Gently connect all HDMI inputs and outputs with the shortest
HDMI cables you can find. Make sure the HDMI cables and
especially the connectors are top quality.

Connection and Operation:

After connecting the HDMI wires, insert the 5 volt plug on the
power supply to the HDMIDA4. Next plug the AC side of the
power supply into the wall outlet. Turn on the power switch.

Troubleshooting:

If the HDMIDA4 does not appear to be functioning, make certain
the source and the destination devices connected are
functioning and turn on. Reconnect the devices using maximum
3 meter (10 foot) long cables (in other words make sure the
problem is not long cables in which case a HDMI balun may be
required). If the signal is present then make sure the HDMIDA4
is getting power. If it still does not work carefully inspect the
cables and connectors for any damage.

Non HDCP Compliant Devices:

If a destination device does not appear to work, make certain
that the device is HDCP compliant. A non-HDCP compliant
device will not work with a signal that has HDCP encoding
present.

If problems are experienced with this product, please call our
tech line for help at 1 800 566 5579.