Knightsbridge WPCWA Installation Instructions

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.

of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
This product contains a non-replaceable LED light source.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its
life. Check local authorities for where facilities exist.

ML ACCESSORIES LTD, UNIT E CHILTERN PARK,

BOSCOMBE ROAD, DUNSTABLE LU5 4LT,

(EU) AUTHORISED REPRESENTATIVE

52531 ÜBACH-PALENBERG, GERMANY

230V
50Hz

SUPPLIED BY:

(UK)

WWW.MLACCESSORIES.CO.UK

SLV LIGHTING GROUP,

DAIMLERSTRASSE 21-23,

EMAIL: [e-mail]

MADE IN CHINA

IP65

>80

CRI

-20~
45°C

TA

INSTALLATION & MAINTENANCE MANUAL

WPCWA

WARRANTY

This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place

WPCWA INSTRUCTION MANUAL.indd 1-3WPCWA INSTRUCTION MANUAL.indd 1-3 25/01/2024 17:17:3525/01/2024 17:17:35

134

JBJAN24_V1

GENERAL INSTRUCTIONS

rating, and secure the baseplate to the surface (see Fig. 2)

Fig. 2

Fig. 2

backplate

Live (brown), E – Earth (green/yellow), N – Neutral (blue). The earth terminal is non-functional and only
provided for convenience. Two cables can be inserted into the push-fit terminal block in order to
achieve loop-in/loop-out wiring

Fig. 3

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
WPCWA

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• This product should be installed in the upright position

• Do not overload this accessory or subject it to conditions outside its rating

• This product is Class II double insulated

• This product is IP65 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP
rated junction boxes should be used where required

• The power source connections should be local and accessible via a suitable IP rated enclosure

• Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the fitting

• Unscrew the four front screws to gain access (see Fig. 1)

Fig. 1

• Using the back plate as a template, mark the location for, and drill the fixing holes ensuring not to infringe
with any gas/water pipes or electrical cables

• For side cable entry, drill out one of the 20mm drilling guides on the side of the fitting and fit a suitable
external grommet or compression gland (not included)

• Feed the mains cable through the back of the casing or side, using a rubber grommet to retain IP rating, and
secure the baseplate to the surface (see Fig. 2)

Fig. 2

Fig. 2

• For surface mounted wiring, a suitable IP rated gland can be used to feed through the side of the backplate

• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3): L – Live
(brown), E – Earth (green/yellow), N – Neutral (blue). The earth terminal is non-functional and only provided
for convenience. Two cables can be inserted into the push-fit terminal block in order to achieve loop-in/loop
out wiring

Fig. 3

• Secure the mains cable under the cable clamp and refit the terminal cover

• Select the required colour temperature via the three-position switch on the rear of the luminaire and required
wattage on two-position switch

• The sensor will be attached via the plug within the fitting, if the sensor is not required, this can be unplugged

Fig. 4

• Switch on and check for correct operation

WPCWA INSTRUCTION MANUAL.indd 4-6WPCWA INSTRUCTION MANUAL.indd 4-6 25/01/2024 17:17:3625/01/2024 17:17:36