INSTALLATION & MAINTENANCE MANUAL
WALL4LSS / WALL5LSS
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
WALL4LSS / WALL5LSS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class I and must be earthed
• This product series is IP44 rated
INSTALLATION
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP
rated junction boxes should be used where required
• Carefully remove the two nuts and O-rings securing the baseplate to the luminaire (see Fig. 1)
Remove nuts
Fig. 1
Remove nuts
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to infringe
with any gas / water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate using the
screws provided (see Fig. 2)
Fig. 2
• Connect the luminaire to the mains supply ensuring that correct polarity is observed (see Fig. 3): L - Live
(brown), E - Earth (green/yellow), N - Neutral (blue)
Fig. 3
• Replace the luminaire onto the baseplate and fasten the O-rings and nuts
• Unscrew the bezel, insert a suitable GU10 lamp and carefully replace the bezel ensuring that the seal is in
place and not damaged
• Push the PIR lid down to uncover the PIR adjustment dials (see Fig. 4)
• Turn the time setting to the minimum (anti-clockwise) and the lux setting to the maximum (clockwise)
• Switch on power to the fitting and conduct a walk test – this is to check the area that the sensor is detecting,
and to adjust the detection setting as required
• Once the detection area is set, adjust the time and lux settings as required. Turn the power to the luminaire
off for 10 seconds and on again for the PIR settings to be registered
• Check for correct operation
PIR SETTINGS
• Sensor detection angle: 1100
• Sensor duration: 10 seconds – 4 minutes
• Detection range: up to 8m when mounted at height of 2.4m
• Sensor lux settings: 10 lux – 2000 lux
The sensor has a manual override function. Switch the power off and on twice within a 3 second period to
activate the manual override. Repeat to return to PIR function.
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
WARNING
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
If installed outdoors, a light film of acid-free oil is recommended after installation and maintained periodically
(2-3 times a year) to aid corrosion prevention.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
INTERNATIONAL
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
CONTACT DETAILS
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
DCAUG21_V3
Loading...