Page 1
INSTALLATION & MAINTENANCE MANUAL
VFCFBC / VFCFC / VFCFW / VFCFIPBC / VFCFIPC
VFCFIPW / VFCFTBC / VFCFTC / VFCFTW
Page 2
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
VFCFBC / VFCFC / VFCFW / VFCFIPBC / VFCFIPC / VFCFIPW / VFCFTBC / VFCFTC
VFCFTW
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with
insulation)
• This product is Class I and must be earthed
• The VFCFxx and VFCFTxx series are IP20 rated; the VFCFIPxx series is IP65 rated
Page 3
INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring
not to infringe with any joists, gas/water pipes or electrical cables
Fig. 1
• Slot the terminal block into position on the fitting, and open the terminal access cover with
the aid of a flat-head screwdriver (see Fig. 2)
Page 4
Fig. 2
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3):
L - Live (brown), E - Earth (green / yellow), N - Neutral (blue). Two cables can be inserted into the
push-fit terminal block in order to achieve loop in / loop-out wiring
Fig. 3
• Secure the mains cable under the cable clamp by closing the lid tightly
• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 4)
Page 5
Fig. 4
• Remove the bezel by turning anti-clockwise (see Fig. 5), insert a suitable GU10 lamp into the
bezel, and connect the lamp to the lamp holder
Fig. 5
• Insert the lamp into the body of the downlight and secure by turning the bezel clockwise. If
using the VFCFIPxx series, please ensure both gaskets are in place. One gasket is in the bezel
and the other is around the base of the fitting (see Fig. 6)
Page 6
Fig. 6
• Switch on and check for correct operation
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This product is dimmable dependent on lamp type.
Page 7
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
Page 8
ACCESSORIES LTD
08
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
DCJUN20_V1
Loading...