Knightsbridge UCLCT4, UCLCT9 Installation Instructions

INSTALLATION & MAINTENANCE MANUAL

UCLCT4 / UCLCT9 / UCLCT13 / UCLCT18

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
UCLCT4 / UCLCT9 / UCLCT13 / UCLCT18

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified
electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location

for installation

• This product is for indoor use only

• This product is Class II double insulated

• This product is IP20 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please

confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide a suitable power supply to the required position of the luminaire and connect to
the supplied power cable ensuring correct polarity is observed

• Mark the location of the fixing holes for the mounting clips. The mounting clips should be
spaced so as to distribute the weight of the luminaire evenly. Drill the holes ensuring not
to infringe with any gas / water pipes or electrical cables (see Fig. 1)

Fig.1

• Connect the power cord to the mains supply ensuring the correct polarity is observed:
L -Live (brown), N - Neutral (blue), and plug into the luminaire

• Multiple fittings can be linked together using a coupler (included) or link leads (available
separately) up to a maximum of 20 fittings

• Switch on and check for correct operation

CHANGING THE COLOUR TEMPERATURE

The colour temperature of an individual fitting can be changed by means of the switch
located on the fitting.
The colour temperature of a group of fittings can be changed by means of a wall switch.

• To change colour temperature, switch off and on again within one second. The colour will
change each time this is done

• To retain colour temperature, switch off for longer than three seconds before switching on
again. The colour temperature will be retained

• If any of the luminaires are switched off and on again for an interval between one and

three seconds, they may go out of synchronisation with each other. If this happens the
switches located on the individual fittings must be used to resynchronise them

• The switch on each individual fitting will only affect the colour temperature of that fitting,
not of those connected after it

WARNING

This luminaire must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class F to Regulation (EU)
No. 2019/2015.
This product contains a non-replaceable LED light source and control gear.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 2 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch codes will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation costs
associated with the replacement product. Your statutory rights are not affected.
ML Accessories reserve the right to alter product specification without prior notice.

60

DCJUL21_V2