Knightsbridge TRLED14EM, TRLED15EM, TRLED15EMD, TRLED16EM, TRLED16EMD Installation Instructions

INSTALLATION & MAINTENANCE MANUAL

IP

65

230V

50Hz

TRLEDxxEM

52

1

GENERAL INSTRUCTIONS

TRLEDxx

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.

These instructions should be used to aid installation of the following products:

TRLED12 / TRLED14 / T RLED15 / TRLED16 / TRLED22 / TR LED24 / TRLED25 / TRLED26

SAFETY

• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this luminaire and LED load is fitted) does not exceed the

rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• This product is Class I and must be earthed

• This product is IP65 rated

• This product is non-dimmable

Note: Outdoor electrical installations should be protected by an earth leakage circuit breaker such as a residua l current
device (RCD)

INSTALLATION

Note: If this luminaire is being used in conjunction with external PIR or sensors, please confirm with the manufacturer of

the sensors that they are compatible with LED luminaires

• Provide power to the required point of installation

• Important: Subject to the sur face foundation material, ensure the correct fixings are used if installed outside, the

mains cable should be connected into a suitable IP rated junction box

• Referring to Fig 1, using the mounting brackets as a template, mark the location of the fixing holes. Drill the fixing

holes ensuring not to infringe with any joists, gas/water pipes, or electrical cables that may be hidden behind the
surface

• Unfasten clips on either side of the fitting (see Fig 2)

These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
TRLED14EM / TRLED15EM / TRLED15EMD / TRLED16EM / TRLED16EMD / TRLED24EM / TRLED25EM /

TRLED25EMD / TRLED26EM / TRLED26EMD

SAFETY

• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this luminaire and LED load is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• We recommend a minimum charge period of 24 hours before completing an initial emergency duration test

• This product is Class I and must be earthed

• Installing in areas where the temperature consistently drops below 0°C may shorten the battery life

• This product is IP65 rated

• This product is non-dimmable

Note: Outdoor electrical installations should be protected by an earth leakage circuit breaker such as a
residual current device (RCD)

INSTALLATION

Note: If this luminaire is being used in conjunction with external PIR or sensors, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires

• Provide power to the required point of installation

• Important: Subject to the surface foundation material, ensure the correct fixings are used if installed outside, the

mains cable should be connected into a suitable IP rated junction box

• Referring to Fig 1, using the mounting brackets as a template mark the location of the fixing holes. Drill the fixing

holes ensuring not to infringe with any joists, gas/water pipes, or electrical cables that may be hidden behind the
surface

Fig 1

• Unfasten clips on either side of the fitting (see Fig 2)

Fig 2

2

TRLED14EM

TRLED15EM/EMD

TRLED16EM/EMD

TRLED24EM

TRLED25EM/EMD

TRLED26EM/EMD

L (mm) L (ft) A1 (mm)

1263 4 900

1563 5 1000

1828 6 1000

1263 4 900

1563 5 1000

1828 6 1000

• Remove the diffuser

• Unfasten clips on either side of the fitting (see Fig 2)

Fig 2

• Remove the diffuser

• Remove the gear tray by pinching the clips at the two locations (see Fig 3)

Pinch at these points

Pinch at these points

N

1

2

• Remove the gear tray by pinching the clips at the two locations (see Fig 3)

Fig 3

• When using as a singular fitting, feed cable through compression gland (supplied) at the end of the fitting

• Connect the battery pack to the emergency inverter via the plug and socket
Connect the Neutral (blue), Earth (yellow and green), Live (1) and Switched Live (2) (see Fig 4)

Fig 4

• Replace the gear tray and diffuser ensuring all clips are fastened correctly

• Align the fitting with the mounting brackets and fix into place

• Switch on power supply and check for correct operation

Note: This fitting can be linked to another fitting by using the terminal connector (see Fig 4) at the opposite end
to the incoming power supply. There are knock-outs at both ends of the fitting which can be drilled using a 20mm
holesaw. The IP65 rating will be maintained when a 20mm compression gland (supplied) is used in the drilled hole.

WARNING

This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

The product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for
where facilities exist. If the batteries have been left in a discharged state for an extended period, we recommend
that one or more charge and discharge cycles are performed, which should restore the battery to its full capacity
The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste. Clean with a soft dry cloth only, do not use aggressive cleaning
products or solvents which may damage the product.

3

WARRANTY

This product has a warranty of 5 years (excluding battery) from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of the batch
codes will invalidate the warranty. If this product should fail within its warranty period it should be returned to
the place of purchase for a free of charge replacement. Warranty only valid if test procedure BS5266 has been
complied with. ML Accessories does not accept responsibility for any installation costs associated with the
replacement product. Your statutory rights are not affected.
ML Accessories reserve the right to alter product specification without prior notice.

TESTING FOR EMERGENCY LUMINARES

RECOMMENDED ROUTINE TEST PROCEDURE IN ACCORDANCE WITH BS5266

We recommend a minimum charge period of 24 hours before completing an initial commissioning emergency
duration test

Daily check – check that the status GREEN LED indicator is illuminated.
Monthly functional test – simulate a mains supply failure for approx. 30 secs by operation of key switch or switching

off a circuit breaker. Ensure normal supply is restored after test and the indicator status LED is illuminated.
Annual full three hour duration test - conduct a three hour continuous duration test. Simulate a mains supply
failure for three hour continuous test by operation of key switch or switching off circuit breaker. Ensure normal
supply is restored after test and the indicator status LED is illuminated.
If the luminaire fails any of the above tests, please consult a qualified electrician

TEST RECORD SHEET

INITIAL COMMISSIONING

3 HOUR TEST

MONTH TEST

1 FUNCTIONAL

2 FUNCTIONAL

3 FUNCTIONAL

4 FUNCTIONAL

5 FUNCTIONAL

6 FUNCTIONAL

7 FUNCTIONAL

8 FUNCTIONAL

9 FUNCTIONAL

10 FUNCTIONAL

11 FUNCTIONAL

12 3 HOUR

FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR

SIGNED DATE SIGNED DATE SIGNED DATE SIGNED D ATE SIGNED DAT E

SIGNED DATE

Installed by: Installation date:

Contact number:

ML Accessories Limited
LU5 5TA

www.mlaccessories.co.uk

AKJUN18_V1

4