Knightsbridge TORCW2, TORCW4, TORCW5, TORCW6 Installation Instructions

INSTALLATION & MAINTENANCE MANUAL

TORCW2 / TORCW4 / TORCW5

TORCW6

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid the installation of the following products:
TORCW2 / TORCW4 / TORCW5 / TORCW6

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• This product is Class I and must be earthed

• This product is IP65 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable
IP rated junction boxes should be used where required

• Round cable should be used for the mains supply. The use of a flat cable will cause water to ingress into
the fitting

• Using the mounting bracket as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables. Fixing centres are shown in Fig. 1

INSTALLATION & MAINTENANCE MANUAL

Product

Length (mm)

Length (ft)

Fixings centres (mm)

TORCW2

650 2 390

TORCW4

1260 4 900

TORCW5

1560 5 1000

TORCW6

1820 6 1000

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

the circuit cable, fuse, or circuit breaker

Suitable IP rated junction boxes should be used where required

into the fitting

to infringe with any gas/water pipes or electrical cables. Fixing centres are shown in Fig. 1

Product

Length (mm)

Length (ft)

Fixings centres (mm)

TORCDA4

1260 4 900

TORCDA5

1560 5 1000

TORCDA6

1820 6 1000

Fig. 1

• Secure the brackets to the surface using suitable fixings

• Unfasten the clips on either side of the luminaire

• Remove the gear tray from the base by pinching the clips at the two locations (see Fig. 2)

Fig. 2

• Feed the mains cable through the compression gland provided at the end of the luminaire

• Ensuring correct polarity is observed, carefully wire as shown in Fig. 3. Two cables can be inserted into the
push-fit terminal block in order to achieve loop-in/loop-out wiring

Fig. 3

L – Live (brown), E – Earth (green/yellow), N – Neutral (blue).

• Select the desired driver output and colour temperature via the switches on the driver (see Fig. 4)

Fig. 4

• Align the body with the mounting brackets and clip it into place

• Tighten the compression gland ensuring a tight seal is made

• Reattach the gear tray to the base

• Switch on and check for correct operation

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class C to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.

This product contains an LED light source which can be replaced by a professional and a control gear which
can be replaced by a professional.

This product contains a light source of energy efficiency class C to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains an LED light source which can be replaced by a professional and a control gear which
can be replaced by a professional.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do
not use aggressive cleaning products or solvents that may damage the product.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.

WARRANTY

This product has a warranty of 5 years from the date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch
code will invalidate the warranty. If this product should fail within its warranty period, it should be returned
to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

Supplied By:

ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,

nnuks Holding GmbH, Niederkasseler Lohweg 18,

(UK) Manufacturer

www.mlaccessories.co.uk

(EU) Authorised Representative

40547 Düsseldorf, Germany,

Email: [e-mail]

-20

~40°C

TA

52

AVMAR22_V1