Knightsbridge TNXQUADW, TNXQUADBK, TNXONEBK, TNXONEW Installation Instructions

INSTALLATION & MAINTENANCE MANUAL

TNXQUADW / TNXQUADBK

TNXONEBK / TNXONEW

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
TNXQUADW / TNXQUADBK / TNXONEBK / TNXONEW

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• This product is Class II double insulated

• This product is IP65 rated

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the

manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP
rated junction boxes should be used where required

• Remove the diffuser from the luminaire housing by unscrewing the four screws

• Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not to
infringe with any gas/water pipes or electrical cables

• Feed the mains cable through the rubber grommet to retain IP rating, and secure the base to the surface
using the plugs and screws provided

INSTALLATION & MAINTENANCE MANUAL

• Ensuring correct polarity is observed, carefully wire as shown in Fig. 1. Two cables can be inserted into

the push-fit terminal block in order to achieve loop-in/loop-out wiring. The earth terminal is non-functional

and only provided for convenience

Fig. 1

• Choose the required driver output and colour temperature via the switches on the driver (see Fig. 2)

Fig. 2

• Attach the LED plate to the luminaire body by aligning the four butterfly screws on the body with the
corresponding holes on the plate then turn clockwise to lock into place (see Fig. 3)

Fig. 3

• Re-attach the diffuser to the luminaire body using the four screws

• Switch on and check for correct operation

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains an LED light source which can be replaced by a professional and a control gear which can
be replaced by a professional.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist

WARRANTY

This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.

230V
50Hz

(UK) MANUFACTURER

ML ACCESSORIES LTD,

UNIT E CHILTERN PARK,

BOSCOMBE ROAD, DUNSTABLE

LU5 4LT,

WWW.MLACCESSORIES.CO.UK

IP65

SUPPLIED BY:

(EU) AUTHORISED REPRESENTATIVE

52531 ÜBACH-PALENBERG, GERMANY

-20~

°C

35

TA

02

SLV LIGHTING GROUP,

DAIMLERSTRASSE 21-23,

EMAIL: [e-mail]

MADE IN CHINA

AKDEC22_V1