Knightsbridge RW6KW, RW6KRGBW Installation Instructions

LET’S GET

YOU SET UP

USER GUIDE

Hey Google

works with

Download the
SmartKnight App

On Google Play (AndroidTM) or App Store® (Apple®).
Open the app, tap “Register” and follow the on-screen instructions

Add Device

(2.4 Ghz only)

To add a device tap the “+” on top right corner, select the product category
and follow the on-screen instructions

Enjoy

Enjoy your connected product. For more in-depth instructions,
please see section titled “Wi-Fi Control” in this leaflet

Setting up Voice Assistants

Enable the “SmartKnight” skill in either voice assistant and follow the
app instructions to control your device(s) with your voice.

Visit http://www.mlaccessories.co.uk for further assistance

INSTALLATION & MAINTENANCE MANUAL

RW6KW / RW6KRGBW

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the end
user for future reference and maintenance.
These instructions should be used to aid the installation of the following products:
RW6KW / RW6KRGBW

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation

• If used under insulation, the insulation should be laid unbroken over the luminaire (not packed
around it). Only mineral wool style insulation may be used

• This product is for indoor use only

• This product is Class II double insulated

• This product is IP65 rated (IP20 from above)

INSTALLATION

Note – Please note that these luminaires are incompatible with dimmers.

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables

Fig. 1

• Insert a flat-head screwdriver into the access slots on the rear of the driver then carefully push to
remove the cover to access the mains terminal block

• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2):
L - Live (Brown), E - Earth (Green/Yellow), N - Neutral (Blue). The earth terminal is non-functional
and only provided for convenience. For RW6KW only, two cables can be inserted into the push-fit
terminal block to achieve loop in/loop-out wiring

Fig. 2

• Refit the terminal cover securely

• To change the bezel, turn anti-clockwise ad remove, align the new bezel with the front of the
luminaire and turn clockwise

• Lift both of the spring clips on the sides of the luminaire and push into the ceiling

• Switch on and check for correct operation

Note – Please note that it is normal for the luminaire to flash when switched on for the first time.
When the luminaire is flashing, it means that it is in pairing mode.

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015
and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a non-replaceable control gear.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product.
This product is dimmable via app only.
This product should be dismantled for disposal when it reaches the end of its life. Please see website
for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.

WI-FI CONTROL

• Download the SmartKnight app on Google Play or the App Store

• Once the app is downloaded, open the app and tap “Register” then follow the on-screen
instructions

• To add a luminaire to the app, switch on the power to the fitting and tap “+” on the top right corner

• Select “Lighting”

• Connect to the desired Wi-Fi network and tap “Next”. Please note only 2.4 GHz networks are
supported and make sure your device is connected to the same Wi-Fi network

®

• If the light is flashing rapidly, skip the reset procedure and tap “Confirm the light is flashing
rapidly” and then tap “Next”. If the light is not flashing, follow the on-screen instructions to reset it

• After the luminaire has been added successfully to the app, it can be named and added to a room.
After naming the luminaire, tap “Done”

ADDITIONAL ACCESSORIES

Code Model

RW6BC Bezel - Brushed Chrome

RW6C Bezel - Chrome

RW6MB Bezel - Matt Black

RW6MW Bezel - Matt White

Code Model

RW6FBC Flat Bezel - Brushed Chrome

RW6FC Flat Bezel - Chrome

RW6FMB Flat Bezel - Matt Black

RW6FMW Flat Bezel - Matt White

RW6FBR Flat Bezel - Brass

WARRANTY

This product has a warranty of 2 years from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations (BS7671),
improper use, or removal of the batch code will invalidate the warranty. If this product should
fail within its warranty period, it should be returned to the place of purchase for
a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

Google, Android and Google Play are trademarks of Google LLC.

Supplied By:

ML Accessories Ltd, Unit E Chiltern Park,

35°C

TA

118

(UK) Manufacturer

Boscombe Road, Dunstable LU5 4LT,

www.mlaccessories.co.uk

(EU) Authorised Representative

nnuks Holding GmbH, Niederkasseler

Lohweg 18,

40547 Düsseldorf, Germany,

Email: [e-mail]

AVJUL22_V4

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with CE marking

ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

CE marking legislation

In Accordance with the following Directives:

2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive

Including Legislation

1907/2006 REACH
2015/863 RoHS
2021/341 ERP

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The product complies with all essential requirements of
the directives.

Scott Brewer Catherine Connolly
Technical Manager CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with UKCA marking

ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

UKCA marking legislation

UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021

Included Legislation

UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The products comply with all essential requirements of
the directives.

Scott Brewer Catherine Connolly
Head of Technical CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.