Knightsbridge RW6WW, RW6CW, RW6CCT Installation Instructions

INSTALLATION & MAINTENANCE MANUAL

RW6WW / RW6CW / RW6CCT

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
RW6WW / RW6CW / RW6CCT

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation

• If used under insulation, the insulation should be laid unbroken over the luminaire (not
packed around it). Only mineral wool style insulation may be used

• This product is for indoor use only

• This product is Class I and must be earthed

• This product is IP65 rated (IP20 from above)

location for installation

be used where required

infringe with electrical cables, water/gas pipes or ceiling joists

72mm

INSTALLATION

Note - If this product is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring

not to infringe with any joists, gas/water pipes or electrical cables

Fig. 1

• With the aid of a cross-head screwdriver,

L

L EE

N

N

remove the cover to access the mains
terminal block (see Fig. 2)

Fig. 2

• Connect the luminaire to the mains supply ensuring that correct polarity is observed:
L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig. 3)

• Two cables can be inserted into the push-fit terminal block in order to achieve loop

in/loop-out wiring

Fig. 3

• Lift both of the spring clips on the sides of the fitting and push into the ceiling

• Switch on and check for correct operation

ADJUSTABLE CCT FITTING ONLY (RW6CCT)

COLOUR CHANGE

• To change the colour temperature of the fitting, switch the fitting on, off, and on again

within 2 seconds. Repeat this switching cycle until desired colour temperature has been
achieved (see Fig. 4)

Fig. 4

MEMORY FUNCTION

• The luminaire will always remain the same colour temperature until the above switching
cycle has been carried out

RESET FUNCTION

• To reset the fittings back to warm white, turn on the fittings and leave them on for 5

seconds

• Switch the fittings off/on 4 times within 6 seconds

• Upon the 4th “on” switch, all luminaires will revert back to warm white

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class B (RW6CW) / C (RW6WW, RW6CCT)
to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a non-replaceable control gear.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product.
This product is dimmable using trailing-edge dimmers, please check compatibility before installation.
This product should be dismantled for disposal when it reaches the end of its life. Please see website
for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.

WARRANTY

This product has a warranty of 5 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

Supplied By:

ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,

nnuks Holding GmbH, Niederkasseler Lohweg 18,

(UK) Manufacturer

www.mlaccessories.co.uk

(EU) Authorised Representative

40547 Düsseldorf, Germany,

Email: [e-mail]

118

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

DCMAY22_V5