Page 1
SUPPLIED BY:
ML ACCESSORIES LTD, UNIT E CHILTERN PARK,
BOSCOMBE ROAD, DUNSTABLE LU5 4LT,
(UK) MANUFACTURER
WWW.MLACCESSORIES.CO.UK
(EU) AUTHORISED REPRESENTATIVE
SLV LIGHTING GROUP,
DAIMLERSTRASSE 21-23,
52531 ÜBACH-PALENBERG, GERMANY
EMAIL: EPREL@GROUP.SLV.COM
MADE IN CHINA
230V
50Hz
PWL5 INSTRUCTIONS_SPREADS.indd 1-3PWL5 INSTRUCTIONS_SPREADS.indd 1-3 13/10/2023 14:54:1213/10/2023 14:54:12
IP20
141
INSTALLATION & MAINTENANCE MANUAL
PWL5
JBSEP23_V1
Page 2
GENERAL INSTRUCTIONS
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
PWL5
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Using the mounting plate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L – Live (brown),
E – Earth (green/yellow), N – Neutral (blue)
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
PWL5
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
INSTALLATION
• Provide power to the required point of installation
• Using the mounting plate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L – Live (brown), E –
Earth (green/yellow), N – Neutral (blue)
Fig. 1
• Fix the mounting plate to the wall using screws, wall plugs and washers provided (see Fig. 1)
• Insert a suitable G9 lamp to lamp holder and fix the body of the luminaire to the mounting plate (see Fig. 1)
• Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist
WARRANTY
This product has a warranty of 2 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
PWL5 INSTRUCTIONS_SPREADS.indd 4-6PWL5 INSTRUCTIONS_SPREADS.indd 4-6 13/10/2023 14:54:1213/10/2023 14:54:12
Loading...