INSTALLATION & MAINTENANCE MANUAL
LUM40 / LUM70
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
LUM40 / LUM70
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
INSTALLATION
Note - This product is designed to fit into a luminaire (not included), it is not designed to be installed as a
standalone fitting.
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED lamps.
• Provide power to the required point of installation
• Remove the lampholder (if fitted) and terminal block (if necessary) from the chosen luminaire
• Disconnect the lamp part of the product from the driver and terminal block
• Select the required colour temperature on the rear of the lamp, and insert it into the luminaire following
manufacturer’s instructions
• Open the driver enclosure to access the terminal block (see Fig. 1)
Fig. 1
• Connect to the mains supply ensuring the correct polarity is observed (see Fig. 2): L – Live (brown), E – Earth
(green/yellow), N – Neutral (blue). The earth terminal is non-functional and only provided for convenience.
Two cables can be inserted into the push-fit terminal block in order to achieve loop-in/loop-out wiring
Fig. 2
• Close the terminal block cover and select the required wattage output via the switch on the side of the
driver enclosure
• Connect the lamp to the driver via the plug and socket
• Complete installation of the luminaire following manufacturer’s instructions
• Switch on and check for correct operation
WARNING
All parts of this product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
SUPPLIED BY:
230V
50Hz
ML ACCESSORIES LTD, UNIT E CHILTERN PARK,
BOSCOMBE ROAD, DUNSTABLE LU5 4LT,
(UK) MANUFACTURER
WWW.MLACCESSORIES.CO.UK
(EU) AUTHORISED REPRESENTATIVE
SLV LIGHTING GROUP,
DAIMLERSTRASSE 21-23,
52531 ÜBACH-PALENBERG, GERMANY
EMAIL: EPREL@GROUP.SLV.COM
MADE IN CHINA
IP20
>90
CRI
25°C
TA
55
DCFEB23_V1
Loading...