These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
LED3xxx / LED5xxx / LED11xxx / LEDT3xxx / LEDT5xxx / LEDT11xxx
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
• This product is for indoor use only
• This product is Class III
• This product series is IP20 rated
• This product is dimmable with LEDDIMMER or LEDTD1* (*suitable for flat range only)
INSTALLATION
• Provide power to the required point of installation
• Using the clip as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any
gas / water pipes or electrical cables and insert the luminaire into the clips until it locks into place. (see Fig. 1)
INSTALLATION & MAINTENANCE MANUAL
(BS7671) and current Building Regulations.If in any doubt, consult a qualified electrician
the circuit cable, fuse,or circuit breaker
installation
any gas / water pipes or electrical cables and insert the luminaire into the clips until it locksinto place.(see Fig.1)
INSTALLATION & MAINTENANCE MANUAL
(BS7671) and current Building Regulations.If in any doubt, consult a qualified electrician
the circuit cable, fuse,or circuit breaker
installation
any gas / water pipes or electrical cables and insert the luminaire into the clips until it locksinto place.(see Fig.1)
constant voltage driver(LEDAD36 not supplied), Live (brown), Neutral (blue)(see Fig.2)
Fig. 1
• Ensuring correct polarity is observed, connect the 230V mains supply to the primary side of the 24V
constant voltage driver (LEDAD36 not supplied), Live (brown), Neutral (blue) (see Fig. 2)
Fig. 2
• Plug the secondary side of the driver into the luminaire
• Switch on and check for correct operation
• Multiple fittings can be connected using connectors and link leads
Note – The flat range of luminaires is equipped with a switch which enables each luminaire to be switched
individually.
ACCESSORIES
*Accessories sold separately
LEDTD1 – a touch dimmer that plugs into the flat range of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
Note – this dimmer has a memory function to retain the brightness level when the mains power is switched off
• Connect the touch dimmer to the luminaire
• Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
ACCESSORIES*
*Accessories sold separately
LEDTD1–a touch dimmer that plugs into the flat range of luminaires and enablesall further units to be controlled by the dimmer up to a maximum of 36W
Note–this dimmer has a memory function to retain the brightness level when the mains power is switched off
•Connect the touch dimmer to the luminaire
•Connect the secondary side of the driver to the touch dimmer (see Fig. 3)
Fig. 3
using suitable 2-core flex (see Fig. 5)
LEDDIMMER – suitable for both the flat and triangular ranges of luminaires and enables all further units to be
controlled by the dimmer up to a maximum of 36W
• Connect the dimmer to the luminaire
• Connect the secondary side of the driver to the dimmer (see Fig. 4)
Fig. 4
LEDTD2 – a plug-in power connector for the flat range of luminaires – for use with drivers that have no
suitable connector on the secondary side
• Unscrew the cap from the top of the connector
• Ensuring correct polarity is observed connect the secondary side of the driver into the power connector using
suitable 2-core flex (see Fig. 5)
• Replace the cap and secure with the two screws
• Connect the power connector to the luminaire
Fig. 5
WARNING
2021 No.1095.
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class C (LED3WCW, LEDT3WCW) / D (LED11WCW,
LED11WWW, LED3WWW, LED5WCW, LED5WWW, LEDT11WCW, LEDT11WWW, LEDT3WWW, LEDT5WCW,
LEDT5WWW) to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable when used with compatible dimmer accessories or a dimmable constant voltage
driver, please check compatibility before installation.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
Supplied By:
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,
nnuks Holding GmbH, Niederkasseler Lohweg 18,
(UK) Manufacturer
www.mlaccessories.co.uk
(EU) Authorised Representative
40547 Düsseldorf, Germany,
Email: eprel@nnuks.com
43
AKJUN22_V3
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.