Knightsbridge GLS9BCKW, GLS9ESKW, CL5KW Installation Instructions

LET’S GET

YOU SET UP

USER GUIDE

Download the
SmartKnight App

On Google Play (AndroidTM) or App Store® (Apple®).
Open the app, tap “Register” and follow the on-screen instructions

Add Device

(2.4 Ghz only)

To add a device tap the “+” on top right corner, select the product category
and follow the on-screen instructions

Enjoy

Enjoy your connected product. For more in-depth instructions,
please see section titled “Wi-Fi Control” in this leaflet

Setting up Voice Assistants

Enable the “SmartKnight” skill in either voice assistant and follow the
app instructions to control your device(s) with your voice.

Visit http://www.mlaccessories.co.uk for further assistance

works with

Hey Google

INSTALLATION & MAINTENANCE MANUAL
GU5KW / CL5KW / GLS9BCKW / GLS9ESKW

WI-FI CONTROL

We recommend enabling the Bluetooth to facilitate faster pairing. Please note that due to
the limitations of Bluetooth only one lamp can be added at a time. If more lamps are to be
added to the app this must be done within the time the lamps are in pairing mode, which is
approximately 2 minutes.

• Download the SmartKnight app on Google Play or the App Store

• Once the app is downloaded, open the app and tap “Register” then
follow the on-screen instructions

• To add a lamp to the app, switch on the power to the lamp
and tap “+” on the top right corner

• Select “Lighting (Wi-Fi)”

• If the light is flashing rapidly and Bluetooth is enabled, the app will
prompt to add the lamp to the app, follow the on-screen instructions
to do so. If the light is not flashing, follow the on-screen instructions to
reset it

• Connect to the desired Wi-Fi network, tap “Confirm” and the app
will start searching for devices. Please note only 2.4 GHz networks
are supported and make sure your device is connected to the same
Wi-Fi network

• After the light has been added successfully to the app, the
lamp can be named and added to a room. After naming the
lamp, tap “Done”

®

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where suitable facilities exist.

WARRANTY

This product has a warranty of 2 years from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations (BS7671),
improper use, or removal of the batch code will invalidate the warranty. If this product
should fail within its warranty period, it should be returned to the place of purchase for
a free of charge replacement. ML Accessories does not accept responsibility for any
installation costs associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification without prior notice.

Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

Google, Android and Google Play are trademarks of Google LLC.

ML Accessories Ltd, Unit E Chiltern Park, Bos-

125

combe Road, Dunstable LU5 4LT,

www.mlaccessories.co.uk

(EU) Authorised Representative

Niederkasseler Lohweg 18,

40547 Düsseldorf, Germany,

Email: [e-mail]

Supplied By:

(UK) Manufacturer

nnuks Holding GmbH,

AVJUL22_V2

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with CE marking

ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

CE marking legislation

In Accordance with the following Directives:

2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive

Including Legislation

1907/2006 REACH
2015/863 RoHS
2021/341 ERP

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The product complies with all essential requirements of
the directives.

Scott Brewer Catherine Connolly
Technical Manager CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with UKCA marking

ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

UKCA marking legislation

UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021

Included Legislation

UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The products comply with all essential requirements of
the directives.

Scott Brewer Catherine Connolly
Head of Technical CEO

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.