Page 1
WARNING
These instructions should be read carefully and
retained after installation by the end user for
future reference and maintenance.
SAFETY
• This product must be installed in accordance
with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building
Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation
or maintenance
• Check the total load on the circuit (including
when this product is fitted) does not exceed
the rating of the circuit cable, fuse or
circuit breaker
• Do not overload this accessory or subject it to
conditions outside its rating
• Please note the IP (Ingress Protection) rating
of this product when deciding the location
for installation
WARRANTY Knightsbridge Wiring Accessories have a have a mechanical warranty of 15 years from date of purchase with the exception of dimmers, USB chargers and speaker products, which have a 2 year warranty. Failure
to install this product in accordance with the current edition of the IEE Wiring Regulations (BS 7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period
it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification without prior notice.
INSTALLATION
• Connect the accessory as per the diagram in this
manual, ensuring the correct polarity is observed:
L – LIVE – Brown
N – NEUTRAL – Blue
EARTH – Green and yellow
• All earth connections must be made and
maintained. Use green/yellow sleeving on earth
conductors that are not insulated
• Check all electrical connections are secure with no
loose strands of cable
• Fit the unit into a suitable wall box taking care
not to compress, damage or trap any cables, and
secure with the screws provided. If using metal
mounting boxes with four lugs, remove the top and
bottom lugs or bend fully back
FLAT PLATE, SCREWLESS AND RAISED EDGE FIXING
• Always ensure the wall surface is flat and smooth
• This unit is fitted with a gasket - this MUST NOT
be removed, this gasket is to stop discolouration
of the plate due to natural moisture in some wall
finishes
• This product must be fitted only after painting and
decorating is complete
• Screwless products only - remove the front plate
by placing a medium size flat-head screwdriver in
the notch at the side and lever off gently. After wiring
and fitting to the wall box as per the instructions in this
document, clip the front plate onto the main assembly
ensuring the screwdriver notch is at the side
METAL CLAD FIXING
• Remove front faceplate and mount rear box in a
suitable location. The back box has multiple 20mm
cable entry points to aid installation
• Wire as per the instructions in this document, and fix
plate to back box using the screws provided
OUTLETS WITH USB CHARGING FUNCTION
These products are designed for charging portable USB
devices only, and contain a short circuit and overload
protection feature. If there is no power from the USB
socket unplug the connected device. Check to ensure the
USB socket and USB device have not come into contact
with water, liquid or debris and the cable to the device
is not damaged. With no device connected to the USB
socket it will automatically reset and be ready for use
WARNING
USB or Bluetooth products, dimmers, shaver sockets and
products with LED or neon indicators must be disconnected
from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this
instruction is not followed. Please note this kind of damage
will void the warranty
! !
This unit should NOT be subject to any insulation resistance
testing, failure to follow this instruction could cause damage
to the USB circuit and void the warranty
GENERAL
This product should be recycled in the correct manner when
it reaches the end of its life. Check local authorities for
where facilities exist.
Clean with a soft dry cloth only, do not use aggressive
cleaning products or solvents which may damage the
product and invalidate the warranty
ML Accessories Limited Unit E, Chiltern Park, Boscombe Road, Dunstable, LU5 4LT www.mlaccessories.co.uk
13A SWITCHED SOCKET 13A SOCKET WITH DUAL USB CHARGER 13A SOCKET WITH QUAD USB CHARGER / QUAD USB CHARGER 13A SOCKET WITH USB AND BLUETOOTH SPEAKER / STAND ALONE BLUETOOTH SPEAKER
.
CHARGING INDICATOR
If you have purchased a model with an LED charger status indicator, it will change colour
depending on the level of current drawn by the connected device. The Red/Green status
indicator gives an approximate charge reading - please refer to device battery level for
true reading.
BLUETOOTH AUDIO
SPECIFICATION
• Output Power: Max. 3W RMS
• Sensitivity: L/R 380MV
• SNR: >80dB
• Speaker Frequency Range:
280Hz – 16KHz
BLUETOOTH CONNECTION
• Press the power button directly under the speaker
– Bluetooth indicator will begin to flash
• Activate Bluetooth pairing on your mobile device and scan for
Bluetooth devices
• Connect to the device named
SPEAKER, SPEAKER01, SPEAKER02 etc.
• Once a connection has been established you will hear a “beep”
sound and the Bluetooth indicator will flash at a different
frequency to confirm
DUAL VOLTAGE SHAVER SOCKET 5A UNSWITCHED ROUND PIN SOCKET
Page 2
decrease the minimum dimming level)
2-WAY SWITCH
L1
L2
L1
L2
LIVE
LIGHT
LIVE
INTERMEDIATE SWITCH
TERMINAL BLOCK
TFROM SUPPLY TO LIGHT
LIVENEUTRAL
EARTH
FROM SUPPLY
13A 2G SWITCHED SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
13A 1G
SWITCHED SOCKET
TO FUNCTIONAL EARTH
LIVE
LIGHT
LIVE
FROM SUPPLYTO LIGHT
L1 L2
COM
SHAVER SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
LIVE
NEUTRAL
LIVE
NEUTRAL
EARTH
TO FUNCTIONAL EARTH
13A 1G SOCKET
WITH USB OUTLET
13A 2G SOCKET
WITH USB OUTLET
LIVE NEUTRAL
EARTH
FROM SUPPLY
13A 1G SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
5A 1G SOCKET
LIVE
LIGHT
LIVE
FROM SUPPLY TO LIGHT
L1 L2
COM
2-WAY DIMMER
For multiple gang Dimmer (2, 3 & 4)
repeat wiring method for each Dimmer.
LIVENEUTRAL
EARTH
FROM SUPPLY
SWITCHED
LIVE
NEUTRAL
EARTH
TO FAN
COM
COM
COM
L1L1L1
Brown sleeve
to be added to
switched live
3-POLE FAN SWITCH
/13A 2G SOCKET
LCOM
L1
L2
LCOM
L1
L2
LCOM
L1
L2
DIMMER SWITCH
(BACK BOX MIN. DEPTH 25MM) (BACK BOX MIN. DEPTH 25-35MM*)
*dependant on wiring conditions
INTERMEDIATE SWITCH
LIVENEUTRAL
EARTH
FROM SUPPLY
13A 2G SWITCHED SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
13A 1G
SWITCHED SOCKET
TO FUNCTIONAL EARTH
LIVE
LIGHT
LIVE
FROM SUPPLYTO LIGHT
L1 L2
COM
SHAVER SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
LIVE
NEUTRAL
LIVE
NEUTRAL
TO FUNCTIONAL EARTH
13A 1G SOCKET
WITH USB OUTLET
13A 2G SOCKET
WITH USB OUTLET
LIVE NEUTRAL
EARTH
FROM SUPPLY
13A 1G SOCKET
LIVE NEUTRAL
EARTH
FROM SUPPLY
5A 1G SOCKET
LIVE
LIGHT
LIVE
FROM SUPPLY TO LIGHT
L1 L2
COM
2-WAY DIMMER
For multiple gang Dimmer (2, 3 & 4)
LIVENEUTRAL
EARTH
FROM SUPPLY
SWITCHED
LIVE
NEUTRAL
EARTH
TO FAN
COM
COM
COM
L1L1L1
Brown sleeve
to be added to
switched live
3-POLE FAN SWITCH
/13A 2G SOCKET
LCOM
L1
L2
DIMMER SWITCH
(BACK BOX MIN. DEPTH 25MM) (BACK BOX MIN. DEPTH 25-35MM*)
*dependant on wiring conditions
10AX 2-WAY SWITCH 10AX INTERMEDIATE SWITCH 10AX FAN ISOLATOR DIMMERS
Terminal positions may alter Terminal positions may alter
FROM SUPPLY TO LIGH
LIVE
LIGHT
LIVE LIGHT
LIVE
LIVE
LCOM
L1
L2
LCOM
L1
L2
ROM SUPPLY TO LIGHT
DCJAN19_V2
LIVE
LIVE LIGHT
LIGHT
LIVE
LIVE
LCOM
L1
L2
TERMINAL BLOCK
TERMINAL BLOCK
L1
L2
L1
L2
LCOM
L1
L2
L1 L2 N
L1 L2 N
Earth
(green/
yellow)
To Lumaire
Switched
Live
(brown)
Live
DIMMERS
Please check with LED lamp manufacturer for
compatibility
Ensure a mixed load is not selected, i.e.
incandescent mixed with LED
Consider the minimum and maximum range
of the dimmer according to the type of load
installed
ADJUSTING THE MINIMUM DIMMING LEVEL
(on products with potentiometer)
• Isolate the power and rotate the dimmer
to its minimum position
• With the aid of a small slotted screwdriver,
rotate the potentiometer (clockwise to
increase, anti-clockwise to decrease the
minimum dimming level)
• Switch on and check for correct operation
• To improve dimming curve repeat the
previous steps
• A small audible buzz may be emitted when
dimming certain products, this is normal
Live Earth Neutral
TO APPLIANCE
13A FUSED SPUR / SWITCHED FUSED SPUR 20A SWITCHES 45A DP SWITCHES
Earth
Neutral
Live
Neutral
Earth
Live
FROM SUPPLY
Live
Earth
Neutral
Live Earth Neutral
TO APPLIANCE
Earth
From supply
FROM SUPPLY
Neutral
Live Earth Neutral
Live
Live
Neutral
Earth
45A DP SWITCHES WITH
13A SWITCHED SOCKETS
These products have no cable entry and should only be used for “hard wired” installations.
45A DP SWITCHES WITH 13A SWITCHED SOCKETS
AND DUAL USB CHARGERS
Loading...