Page 1
INSTALLATION & MAINTENANCE MANUAL
EA1xx / EA2xx
Page 2
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
EA1xx / EA2xx
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not
exceed the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is Class II double insulated
• This product is IP54 rated
Page 3
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
EA1xx / EA2xx
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or m aintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product is IP54 rated
INSTALLATION
Note - Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the fitting.
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable
IP rated junction boxes should be used where required
• Separate the baseplate from the luminaire by removing the nuts on the front
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to infringe
with any gas/water pipes or electrical cables (see Fig. 1)
INSTALLATION
Note - Round cable should be used for the mains supply. The use of flat cable will cause
water ingress to the fitting.
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Separate the baseplate from the luminaire by removing the nuts on the front
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring
not to infringe with any gas/water pipes or electrical cables (see Fig. 1)
Fig. 1
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the
baseplate to the surface using the plugs, screws and rubber washers provided
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: Live
(brown), Neutral (blue)
• Ensuring the gasket on the baseplate is in place, align the luminaire with the baseplate
and secure with the two nuts
Page 4
• Unscrew the bezel, insert a suitable LED lamp (5W max.) and carefully replace the bezel
ensuring that the seal is in place and not damaged. Note that the top and bottom bezels
of the EA2xx are not interchangeable
• Switch on and check for correct operation
GENERAL
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
Page 5
Supplied By:
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road,
Dunstable LU5 4LT, www.mlaccessories.co.uk
nnuks Holding GmbH, Niederkasseler Lohweg 18, 40547
(UK) Manufacturer
(EU) Authorised Representative
Düsseldorf, Germany, www.nnuks.com
Email: eprel@nnuks.com
02
DCMAR22_V1
Loading...