INSTALLATION & MAINTENANCE MANUAL
DC007
It is very important to install and operate this product according to the following
instructions. Failure to do so may render your warranty void.
Accessories list
The door chime kit comes with:
• 1 x Receiver
• 2 x Bell push
• 2 x CR2032 batteries for bell pushes
Depiction of accessories
Receiver
Transmitter Double-sided
(1)
(2)
Receiver front side Receiver back side
• 2 x Double-sided adhesive pads
• 1 x Instruction manual
CR2032
battery
adhesive
(3)
(4)
Transmitter front
cover outside
Instruction
manual
(5)
(6)
(7)
Transmitter front
cover inside
Legends
1. Speaker 5. Front cover and back cover hook
2. Plug 6. Standby holes for screws
3. Push button 7. Release slot
4. Nameplate cover
Specifications
Bell push unit
Power: 3V CR2032 battery (included)
Receiver unit
Power: 230V AC~50Hz
Operating temperature: -30°C to 40°C
Operating range: 100m (dependent on environment)
Selectable tones: 36 melodies available
Digital code type: Auto-learning code set up
Notes before installation
1. Prior to installation and operation, you will require a drill, cross-head screwdriver,
flat-head screwdriver, fixing screws and wall plugs (these items are not included
with this kit)
2. Avoid positioning the bell push on metal frames
3. Avoid positioning above or near heat sources such as radiators, or in damp areas
such as kitchens and bathrooms
Battery installation
Bell push unit
- Each bell push uses a CR2032 battery (included)
- Remove the nameplate cover. Remove the small rubber screw cover in lower
right-hand corner with thin-tipped tweezers or a needle and unscrew the retaining
screw
- Insert a flat-head screwdriver into the slot on the bottom of the bell push and gently
turn to open the front cover
- Install the CR2032 battery ensuring the polarity is correct (+ side up) and replace
front cover
- Replace the retaining screw and rubber cover and replace name plate
Auto-learning code set up
Operation for 2 bell pushes and 1 receiver
1. After battery installation, press the bell push once on the first bell push to
generate a new operation code. Then hold the melody button on the receiver for
3 seconds. The receiver will sound which indicates that a new operation code
is registered and memorized. You can then assign a melody to this bell push by
pressing the melody selection button positioned on side of receiver. Press bell
push once again and this melody will be the pre-set for this bell push.
2. Repeat this process for second bell push
Interference
Should you experience interference from another door chime operating in your area
(for example: receiver sounds for no reason) - remove the batteries from both bell
pushes, unplug the receiver from the socket and leave for 30 seconds - this will
erase the memory. Re-insert batteries in both bell pushes, plug in receiver and
repeat auto learning code set up.
Melodies for the bell push
There are 36 built-in melodies with the receiver. The receiver will sound different
melodies in response to bell push activation. 2 melodies can be set to alert user to
whichever position bell pushes have been installed.
Wall mounting bell push
To install you will require a drill and a cross-head screwdriver
IMPORTANT: Before drilling into any wall or surface, ensure there are no cables or
pipes that could be accidentally damaged.
1. Remove casing as outlined in the battery installation process. Pierce the two
standby holes on the rear casing and affix the bell push rear to the wall at a
suitable height
2. Alternatively, you can attach the bell pushes with the double-sided adhesive tape
included
1
Please note: mounting on PVCu or metal doorframes will reduce the operating
range
1
Receiver unit installation
Plug the receiver unit into a spare power outlet. Please ensure when you test the
receiver it is within the recommended operating range of the 2 bell pushes
2
2
3
User hints
If the receiver does not sound, please check the following:
- Flat batteries in either of the bell pushes – change the batteries
- Wrong battery polarity in either bell push – re-insert batteries correctly
- Units are out of range – operate the receiver within the recommended operation
range
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
WHEN REPLACING BATTERIES
4
AKAPR18_V3
92
5
6
Loading...