Page 1
INSTALLATION & MAINTENANCE MANUAL
2
DC001
It is very important to install and operate this product according to the following
instructions. Failure to do so may render your guarantee void.
Accessories list
The door chime kit comes with:
• 1 x Receiver
• 1 x Bell push
• 1 x 3V CR2032 battery for bell push
Pictures for accessories
Receiver
Names for parts
Transmitter
• 1 x Double-sided adhesive pad
• 1 x Instruction manual
CR2032 battery
Double-sided
adhesive
Instruction
manual
Names of parts
1. Speaker 8. Hanging slot
2. LED indicator 9. Push button
3. Sound-and-flash switch 10. Nameplate cover
4. Battery cover 11. Front and back cover hook
5. Volume button 12. Standby holes for screws
6. Melody selector 13. Interface
7. Auto learning code button
Notes before installation
1. Before installation and operation, you will require a drill, cross-head screwdriver,
flat-head screwdriver, 2 × AA 1.5V batteries, fixing screws
and wall plugs. These items are not supplied with this kit
2. Try to avoid positioning the bell push on metal frames
3. Avoid positioning above heat sources such as radiators, or in damp areas such as
a kitchens or bathrooms
How to use the door chime kit
Pressing the bell push, a wireless signal will be sent to the receiver.
The receiver will be activated and sound. The operating range is 200m (in the open
air) and you can use the receiver virtually anywhere in the home (indoor use only).
However, the transmission range will be reduced if the signal is transmitted through
walls or ceilings. Metal or PVCu doorframes can also reduce the operating range.
Receiver unit
Remove the battery cover and insert 2 x 1.5V AA batteries (not included).
Ensure battery polarity matches the internal markings.
1.5V AA
Alkaline
batteries
Battery cover
Wall mount
To install, you will require a drill and cross-head screwdriver.
IMPORTANT: Before you drill any hole in the wall, please make sure there are no
cables or pipes that may accidentally be damaged.
Bell push unit
1.
Open the bell push with a screwdriver and separate the front cover from the back
cover (as previously described). Penetrate the two standby holes on the back cover
with two screws, then fix the screws onto the wall at a suitable height (see picture 1).
2.
Alternatively, you can attach the bell push with double-sided adhesive tape
(see picture 2)
Mounting on PVCu or metal doorframe surfaces will reduce the transmitting range
Receiver
Load batteries and replace cover
Receiver front side
(8)
(3)
(1)
(4)
(2)
Receiver back side
(5)
(6)
(7)
Transmitter front
cover outside
(11)
(9)
(12)
(10)
(13)
Transmitter back
cover inside
1
Functions instructions
Door chime operation
Press the push button on the bell push unit once, a wireless signal is sent to the
receiver which will sound. The sound will stop as soon as the melody ends. For
repeated sound, press the button again. Please note, holding the button in will not
repeat the sound.
Melody selection
There is a melody selector located on the back of the door chime on the right.
Press the selector to choose a different melody.
Sound and flash
There is a switch on the back of the receiver on the left. Slide the switch to the left
position: the receiver will work with sound only; slide to the middle position: the LED
will flash only; slide to the right position for sound and LED flash.
Volume adjustment
There is a volume button between the melody selector and the sound-and-flash
switch. Press to adjust the sound volume - high, medium or low.
Auto-learning code button
(please see detailed operation ‘Auto-learning code set up’ in this manual).
Nameplate
There is a nameplate position on the bell push for user identification. Remove the
nameplate cover and put a suitably sized label with name or required information,
and replace cover (label is not included with this kit).
Important
1. The receiver is designed for indoor use only
2. Mounting the bell push onto any metal surface or PVCu doorframes will reduce
the operating range
3. Do not expose either unit directly to rain or immerse in water
4. Do not mount either unit close to a fireplace or expose to high temperatures
5. If leaving the door chime for long periods, please remove the battery from
compartment to prevent leakage
6. Please dispose of old batteries in accordance with relevant legislation
Battery installation
Bell push unit
• The bell push uses a 3V CR2032 battery (included)
• Open the bell push by removing the screw cover and screw with a cross-headed
screwdriver. Use a slotted screwdriver to remove the front cover from the rear
cover. Insert battery ensuring correct polarity is observed.
2
User hints
If the receiver does not sound, please check the following:
• Flat batteries in either bell push - change the batteries
• Wrong battery polarity in either bell push re-insert the
batteries correctly
• Units are out of range - operate the receiver within the recommended
operating range
Specification
Bell push unit
Power: 1×3V CR2032 battery (included)
Receiver unit
Power: 2 x 1.5V AA alkaline batteries (not included)
Operating temperature: -30 °C (to +400 °C)
Operating distance: 200 meters (in the open air) (265ft approx.- (in the open air and
suitable conditions)
Selectable tone: Total 36 melodies available
Digital code type: Auto-learning
What is auto-learning code?
The bell push sends a wireless signal to the receiver. The receiver will automatically
register and memorize the signal as an operation code.
The bell push can work with the receiver by using this code.
Auto-learning code set up
The door chime kit is equipped with auto-learning operation code ability.
1. Operation for 1 bell push and 1 receiver
After battery installation on both bell push and receiver, press the bell push once
to generate a new operation code. The receiver will sound which indicates that a
new operation code is registered and memorized
2. Interference from another door chime operating nearby (for example: receiver
sounds for no reason): remove the batteries from the receiver and rest for 30
seconds. This will erase the memory. Insert the batteries, the bell push and
receiver are ready for the new code registration
1
Receiver unit
Fix a screw onto the wall and hang the receiver by the slot at the back of the unit.
Test the receiver before drilling any holes to ensure it is within recommended
operating range.
Note: Alternatively, the receiver can also be placed on a flat surface.
2
3
IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
WHEN REPLACING BATTERIES
BAJAN17_V2
92
4
5
6
Loading...