Page 1
INSTALLATION & MAINTENANCE MANUAL
CRDL10 / CRDL15
CRDL20 / CRDL30
Page 2
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
CRDL10 / CRDL15 / CRDL20 / CRDL30
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to infringe
with any joists, gas/water pipes or electrical cables
Page 3
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
the circuit cable, fuse or circuit breaker
infringe with any joists, gas/water pipes or electrical cables
Product Code
Cut-out diameter (mm)
CRDL10
125
CRDL15
175
CRDL20
175
CRDL30
200
Product Code
Cut-out diameter (mm)
CRDL10
125
CRDL15
175
CRDL20
175
CRDL30
200
GENERAL
This product contains a light source of energy efficiency class B (CRDL15, CRDL20) / C (CRDL30) / D (CRDL10)
to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Fig. 1
• Connect the primary side of the driver to the mains supply ensuring the correct polarity is observed: L - Live
(brown), N - Neutral (blue)
• Lift both of the spring clips on the sides of the fitting and push into the ceiling ensuring the driver is located
away from the body of the luminaire
• Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class B (CRDL15, CRDL20) / C (CRDL30) / D (CRDL10)
to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.
Page 4
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product. This product is dimmable using trailing-edge dimmers, please check compatibility before installation.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its
life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
SUPPLIED BY:
ML ACCESSORIES LTD, UNIT E CHILTERN PARK, BOSCOMBE ROAD,
DUNSTABLE LU5 4LT, WWW.MLACCESSORIES.CO.UK
NNUKS HOLDING GMBH, NIEDERKASSELER LOHWEG 18, 40547 DÜSSELDORF, GERMANY,
(UK) MANUFACTURER
(EU) AUTHORISED REPRESENTATIVE
EMAIL: EPREL@NNUKS.COM
MADE IN CHINA
35°C
TA
118
DCSEP21_V2
Loading...