Knightsbridge BT9ACTEM, BT20ACTEM, BT14ACTEM Installation Instructions

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
BT9ACTEM / BT14ACTEM / BT20ACTEM

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location
for installation

• This product is Class II double insulated

• This product is IP65 rated

INSTALLATION

• Provide power to the required point of installation. Suitable IP rated junction boxes should
be used where required

• Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)

BTxxACT

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

rating of the circuit cable, fuse or circuit breaker

installation

where required

installation

• Provide power to the required point of installation. Suitable IP rated junction boxes should be used
where required

• Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)

pipes or electrical cables

operation (Fig. 5) as required

Fig. 1 Fig. 2

• Remove the fastening screw securing the LED plate and open the LED plate (see Fig. 2)

• Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables

• Feed the cable via the rubber grommet to retain IP rating, and secure the baseplate to
the surface

• Wire for non-maintained operation (Fig. 3), maintained operation (Fig. 4) or switched
maintained operation (Fig. 5) as required

Fig. 3 Fig. 4 Fig. 5

• Connect the battery to the inverter

• Refasten the LED plate screw

• Choose the required colour temperature by means of the DIP switch (see Fig. 6)

Fig. 6

• Reattach the diffuser by rotating clockwise

• Switch on and check for correct operation, ensuring the green indicator LED is illuminated

• We recommend, on commissioning the installation, a minimum charge period of 24 hours
before carrying out an emergency duration test

Note: this fitting shuts off power to the Lithium Ion battery periodically to prevent
overcharging. Therefore, the green LED indicator has been set up to indicate that the
emergency inverter is in good condition, not to indicate that the battery is charging. The
installer must ensure that the battery is connected.

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D (BT9ACTEM) /
E (BT14ACTEM, BT20ACTEM) to Regulation (EU) No. 2019/2015.
This product contains an LED light source which can be replaced by the end user and a
control gear which can be replaced by a professional.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
The batteries in this luminaire are Lithium Ion and must be disposed of correctly. Please
contact the local authorities for the disposal of this toxic waste.

WARRANTY

This product has a warranty of 5 years from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations, improper
use, or removal of the batch codes will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

TEST RECORD SHEET

INITIAL COMMISSIONING

3 HOUR TEST

MONTH TEST

1 FUNCTIONAL

2 FUNCTIONAL

3 FUNCTIONAL

4 FUNCTIONAL

5 FUNCTIONAL

6 FUNCTIONAL

7 FUNCTIONAL

8 FUNCTIONAL

9 FUNCTIONAL

10 FUNCTIONAL

11 FUNCTIONAL

12 3 HOUR

FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR

SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE

SIGNED DATE

Installed by: Installation date:

Contact number:

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk

52

INTERNATIONAL

CONTACT DETAILS

DCJUL21_V2