Knightsbridge BATM6, MODEMKIT, BATM4 User guide

INSTALLATION & MAINTENANCE MANUAL

BATM2 / BATM4 / BATM5 / BATM6 /

MODEMKIT / MODMWS

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
BATM2 / BATM4 / BATM5 / BATM6 / MODEMKIT / MODMWS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is for indoor use only

• This product is Class I and must be earthed

• This product is IP20 rated

INSTALLATION & MAINTENANCE MANUAL

INSTALLATION

Note - Microwave sensors may not be suitable for all installations, for example enclosed
spaces, as they are able to detect movement through non-metallic surfaces like
plasterboard and thin doors.

• Provide power to the required point of installation

• Squeeze the sides and hinge the diffuser away from the fitting (see Fig. 1)

Fig. 1

• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables. The fitting can also be mounted over conduit boxes:
for distance between fixing centres please see below:

• Fix the base to a suitable solid surface using the screws provided.

Fig. 1

Product Code

Distance (mm)

BATM2

415

BATM4

600

BATM5

600

BATM6

600

L1 – Emergency Live (brown), E – Earth (green/yellow), N – Neutral (blue) (see Fig. 2). Two cables
can be inserted into the push-fit terminal block in order to achieve loop-in/loop-out wiring

• Ensuring correct polarity is observed, carefully wire as shown in Fig. 2

• Connect to the mains supply ensuring the correct polarity is observed: L – Live, L1 –
Emergency Live (brown), E – Earth (green/yellow), N – Neutral (blue) (see Fig. 2). Two
cables can be inserted into the push-fit terminal block in order to achieve loop-in/loop
out wiring

Fig. 2

MODEMKIT

Fig. 2

• Install by using the clips to secure them in place

• Luminaire with emergency mode and no sensor connected, connect the connectors
labelled A from the terminal block to A(EM) from the emergency module, connector
labelled B from the driver to B(EM) emergency module, connector labelled C(LED) from
emergency module to C LEDs and connectors labelled (DLED) from emergency module
to D LEDs

• Ensure that the battery is connected by opening the emergency module pack and the
battery connector on the PCB

MODMWS

• Install by using the clips to secure them in place

• Luminaire with no emergency mode and sensor connected, connect the connectors
labelled A from the terminal block to A(S) from the sensor and connector labelled B from
the driver to B(S) from sensor

LAYOUT

DIP SWITCH SETTINGS

Hold Time

3 4 5

5sec

30sec

1min

3min

5min

1 2

Detection area Hold Time

3 4 5

5sec

30sec

1min

3min

5min

10min

20min

30min

1 2

100%

75%

50%

25%

6 7 8

3 4 5

5sec

Detection area

100%

75%

50%

25%

2lx

10lx

25lx

50min

*Disable

Daylight Sensor

When set to Disable, the daylight sensor will switch

Hold Time

30sec

1min

3min

5min

10min

20min

30min

This is the time period the lamp remains at 100%
after no motion is dectected

the lamp on when motion is detected regardless of
the ambient light level

MODEMKIT & MODMWS

• Install the MODEMKIT and MODMWS by using the clips to secure them in place

• Luminaire with emergency mode and sensor connected, connect the connectors labelled
A from the terminal block to A(EM) from the emergency module, connector labelled
A(S) from sensor to connector labelled B(EM) from emergency module, connector
labelled B from the driver to B(S) from sensor, connector labelled
C(LED) from emergency module to C LEDs and connectors labelled D(LED) from
emergency module to D LEDs

• Ensure that the battery is connected which is within the emergency module and the
battery connector on the PCB

NOTE: The MODEMKIT and MODMWS are sold separately

• Refasten the cover

• Switch on and check for correct operation

• Switch on and check for correct operation ensuring the green indicator LED is illuminated

• We recommend, on commissioning the installation, a minimum charge period of 24 hours
before carrying out an emergency duration test

• The test button can be used to simulate a power failure to test the lamp and battery
operation. This can be used to carry out monthly functional testing providing the battery
holds at least a small charge

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No. 2019/2015 and (UK)
2021 No. 1095.

This product contains a non-replaceable LED light source and a control gear which can be replaced by a
professional.



This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class D to Regulation (EU) No.
2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a control gear which can be
replaced by a professional.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
Installing in areas where the temperature consistently drops below 0°C may shorten the
battery life.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
The batteries in the MODEMKIT are Lithium Ion and must be disposed of correctly. Please
contact the local authorities for the disposal of this toxic waste.

WARRANTY

This product has a warranty of 5 years (including battery) from date of purchase. Failure
to install this product in accordance with the current edition of the IEE Wiring Regulations
(BS7671), improper use, or removal of the batch code will invalidate the warranty. If this
product should fail within its warranty period, it should be returned to the place of purchase
for a free of charge replacement. ML Accessories does not accept responsibility for any
installation costs associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification without prior notice.

TESTING FOR EMERGENCY LUMINAIRES

Recommended routine test procedure in accordance with BS5266:

• Daily check – check LED charge indicator is illuminated

• Monthly functional test - simulate a mains supply failure for approx. 30 seconds by
operation of key switch or switching off circuit breaker. Ensure normal supply is restored
after test and ensure charge indicator is illuminated

• Annual 3-hour duration test - simulate a mains supply failure for 3-hour continuous test
by operation of key switch or switching off circuit breaker. Ensure normal supply is
restored after test and ensure charge indicator is illuminated

• If the luminaire fails any of the above tests, please contact a qualified electrician. See
below for test record sheet

INITIAL COMMISSIONING

3 HOUR TEST

MONTH TEST

1 FUNCTIONAL

2 FUNCTIONAL

3 FUNCTIONAL

4 FUNCTIONAL

5 FUNCTIONAL

6 FUNCTIONAL

7 FUNCTIONAL

8 FUNCTIONAL

9 FUNCTIONAL

10 FUNCTIONAL

11 FUNCTIONAL

12 3 HOUR

FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR

SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE

SIGNED DATE

Installed by: Installation date:

Contact number:

TEST RECORD SHEET

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with UKCA marking

ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

UKCA marking legislation

UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021

Included Legislation

UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The products comply with all essential requirements of
the directives.

Catherine Connolly Lee Saunders

CEO Technical Assessment & Compliance Manager

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity

For ML Accessories (Knightsbridge)

Electrical products in accordance with CE marking

ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation

CE marking legislation

In Accordance with the following Directives:

2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive

Including Legislation

1907/2006 REACH
2015/863 RoHS
2021/341 ERP

Safety Standards

Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk

We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The product complies with all essential requirements of
the directives.

Catherine Connolly Lee Saunders

CEO Technical Assessment & Compliance Manager

ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT

This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

SUPPLIED BY:

ML ACCESSORIES LTD, UNIT E CHILTERN PARK,

UK MANUFACTURER

BOSCOMBE ROAD, DUNSTABLE LU5 4LT,

WWW.MLACCESSORIES.CO.UK

EU AUTHORISED REPRESENTATIVE

SLV LIGHTING GROUP,

DAIMLERSTRASSE 21-23,

52531 ÜBACH-PALENBERG, GERMANY

EMAIL: [e-mail]

MADE IN CHINA

230V
50Hz

-20~
45°C

TA

134

JBAPR24_V1