Page 1
INSTALLATION & MAINTENANCE MANUAL
AMLEDB / AMLEDR / AMLEDW
Page 2
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product(s):
AMLEDB / AMLEDR / AMLEDW
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product is IP54 rated
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED lamps/luminaires.
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP
rated junction boxes should be used where required
• Remove the diffuser and gear tray from the body
• Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not to
infringe with any gas/water pipes or electrical cables
• Drill out one of the 20mm drilling guides on the fitting, and fit a suitable external grommet or compression
gland (not included)
Page 3
Suitable IP rated junction boxes should be used where required
• Remove the diffuser and gear tray from the body
• Drill the fixing holes in the rear of the fitting. Mark the location of the fixing holes and drill ensuring not
to infringe with any gas/water pipes or electrical cables
• Drill out one of the 20mm drilling guides on the fitting, and fit a suitable external grommet or
compression gland (not included)
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (Brown),
N - Neutral (Blue) (see Fig. 1)
Fig. 1
• Replace the gear tray and diffuser ensuring the seal is in place
• Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015.
This product contains an LED light source which can be replaced by the end user and a control gear which can
be replaced by a professional.
INSTALLATION & MAINTENANCE MANUAL
• Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (Brown),
N - Neutral (Blue) (see Fig. 1)
Fig. 1
• Replace the gear tray and diffuser ensuring the seal is in place
• Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class E to Regulation (EU) No. 2019/2015.
This product contains an LED light source which can be replaced by the end user and a control gear which can
be replaced by a professional.
Page 4
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
Page 5
INTERNATIONAL
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
CONTACT DETAILS
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
DCAUG21_V3
Loading...