Page 1
Page 2
2
2
Page 3
3
3
Page 4
“
Hi! I’m your K’NEX Building Buddy. When you
see me in the instructions, you’ll want to pay
close attention to the details being pointed out.
”
Ready, Set, Build
To begin your model, find the and follow
the numbers. Each piece has its own shape and
color. Just look at the picture, find the pieces in
your set that match what you see, and snap
them together. Try to hold your model in the
same direction as in the picture so you’ll attach
your pieces to the right place.
Movin’ On
The faded colors tell you this section is
already built. You’ll want to connect the
new section to the place where the arrows
are pointing. These pieces will be in full
color.
Cross-snap
When a Connector snaps on across a Rod, it is referred
to as a “cross-snap”. Cross-snaps sometimes require a
strong push and you might want to ask an adult for
help.
FCC Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including
interference that may cause undesired operation. This model is
tested to comply with FCC standards - FOR HOME OR OFFICE USE.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures: (1) Reorient or relocate the receiving
antenna. (2) Increase the separation between the equipment and
receiver. (3) Consult the dealer or an experienced radio/TV technician.
This Class B digital apparatus complies with Canadian ICES-003.
4
4
BUILDING TIPS:
•Try to face your model in the same direction as shown in
the instructions.
•Some steps include pieces that require a strong “push”to
snap together. You might want to ask an adult for help.
1
K’NEX BUILDING BASICS
K’NEX BUILDING BASICS
1
2
1
Page 5
1
1
7
1
1
1
13
12
1
1
1
1
3
3
27
1
2
2
2
1
2
2
11
19
1
3
1
How to Insert and
Remove Batteries
Use a small Philips Head screwdriver to
loosen the screw, then remove the battery
door. Insert 3 fresh button cell LR44
(A76 or SR44) into each compartment
with the correct polarity (+/-)
Sound doesn’t work? Check to see if you
have fresh button cell batteries and that
they are installed properly.
Parts Checklist
Before you start building, be sure to compare the parts in your set with
the parts listed below. If anything is missing, check out the back cover
of this instructions booklet for how to contact us. We’re here to help!
+
-
5
5
Battery Information:
CAUTION: Do not use Sound Module close to ear! Misuse may cause
damage to hearing.
CAUTION:
• As with all small batteries, the batteries used in this toy should be kept away
from small children, who still put things in their mouths. If they are
swallowed, promptly see a doctor and have the doctor phone 202-625-3333
collect. (US only)
• Make sure batteries are inserted correctly and follow the toy and battery
manufacturer’s instructions.
• Insert batteries with correct polarity (+/-) as shown.
• Do not mix different types of batteries; do not mix alkaline, standard
(carbon-zinc), or rechargeable (nickel-cadmium) batteries. Do not mix new
and used batteries. Only batteries of the same or equivalent type
recommended should be used.
• Remove exhausted batteries from the toy; do not short circuit supply
terminals.
• Remove all batteries if the toy is not used for a long period of time.
• Do not dispose of batteries in a fire; they could leak or explode and cause
injury.
IMPORTANT TIPS:
• The Sound Module comes with 3 batteries already installed in your model.
• Rechargeable batteries are not recommended.
• Remove rechargeable batteries before recharging; they must be charged only
under adult supervision.
• Non-rechargeable batteries must not be recharged.
• Keep components free of dust; do not immerse in water.
Push button
to activate
sounds.
To activate the 2 different sounds,
push the button once to “start
”
the engine, then push again
while playing to “rev”the engine.
Page 6
1
1
2
1 2
-
1
Mikey’s
Swing-Arm Bike
Page 7
2
3
6
5
4
1 6
-
1 2
-
1 5
-
Page 8
3
7
8
9
10
1 10
-
1 6
-
1 8
-
Page 9
12
11
1 12
-
4
1 10
-
Page 10
5
13
14
15
16
1 16
-
1 12
-
13 15
-
Page 11
6
17
18
19
20
21
17 19
-
17 21
-
17
17 19
-
Page 12
7
22
23
24
25
1
25
-
17 21
-
1 16
-
17 23
-
Page 13
8
29
30
26
27
28
26 30
-
26 27
-
Page 14
9
31
32
33
34
1
34
-
26
30
-
1
25
-
26
32
-
Page 15
10
35
36
37
1
37
-
1
34
-
Page 16
11
11
2
1
2
3
4
1 4
-
1 2
-
Mikey’s
Swing-Arm Bike 2
Page 17
12
5
6
7
1 7
-
1 4
-
1 6
-
Page 18
13
8
9
10
11
1 11
-
1 7
-
1 9
-
Page 19
14
12
13
14
15
12 15
-
12 13
-
Page 20
15
16
17
18
19
20
21
12 21
-
12 15
-
12 18
-
Page 21
22
1
22
-
1 11
-
12 21
-
16
Page 22
17
23
24
25
26
1
26
-
1
22
-
Page 23
Loading...