Knape&Vogt PKT-100A User Manual [en, fr, es]
SLIDING DOOR HARDWARE - POCKET DOOR
PKT-100A • For 1 door up to 100 lbs. with thickness of 1-3/8" to 1-3/4"
Tools Required • Outils requis • Herramientas requeridos
Wrench (included) • Clé (incluse) • Llave (incluida)
Drill (3/32") • Perceuse (3/32") • Taladro (3/32")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
CONTENTS
#310312_B (1212)
Assembly
Instructions
A. Track 1
B. Carrier 2
C. Quick Release Top Mount Plate 2
D. Door Guide Kit 2
E. Door Bumper Kit 1
F. #8 x 1" Pan Head Screw 8
G. #8 x 5/8" Truss Head Screw 8
B.
F.
C.
G.
E.
QUINCAILLERIE POUR PORTE COULISSANTE – PORTE
COULISSANTE ESCAMOTABLE
PKT-250A • Pour 1 porte jusqu’à 113,4 kg chacune d’une épaisseur de 3,5 cm à 4,4 cm
CONTENU 2-Portes
A. Coulisse 1
B. Module 2
C. Plaque de montage supérieure 2
à dégagement rapide
D. Ensemble guide de porte 2
CONTENU 2-Portes
E. Ensemble butoir de porte 1
F. #8 x 1" Vis tête cylindrique 8
F. #8 x 5/8" Vis à tête bombée 8
A.
D.
#310312_B (1212)
#310312_B (1212)
Instructions
d’assemblage
HERRAJE PARA PUERTA DE CORREDERA
– EMPOTRADA
PKT-250A • Para 1 puerta de hasta 113,4 kg cada una y de 3,5 cm a 4,4 cm de grosor
CONTENIDO 2-Puertas
A. Caril 1
B. Portador 2
C. Placa de montaje superior 2
fácilmente desmontable
D. Kit de guía de la puerta 2
CONTENIDO 2-Puertas
E. Kit de tope de la puerta 1
F. #8 x 1" Tornillos cabeza plana 8
F. #8 x 5/8" Tornillo de cabeza de armazón 8
#310312_B (1212)
Instrucciones para
el ensamblaje
SLIDING DOOR HARDWARE - POCKET DOOR
PREPARE OPENING
1
Hmax = Door Height + 2-3/8" • Hmin = Door Height + 2-1/8"
Rough Opening Width = 2 x Door Width + 1"
Opening Width
Largeur de l’overture
Ancho de la abetura
Opening Height
Hauteur Ouverture
Altura Abertura
#310312_B (1212)
Assembly
Instructions
1-3/4" - 2"
(4,4 cm - 5,1 cm)
Door Height
Hauteur Porte
Altura Puerta
3/8"
(1 cm)
MOUNT FRAME HARDWARE
2
• Center track in opening.
• IMPORTANT: Place hangers loose into track before
securing.
• Using track as template, mark screw locations.
• Drill 3/32” pilot holes and secure with (#8 x 1”) screws.
• To take advantage of the key-holed slots, be sure
there is a 3/4” opening from the nished opening
to the track. If necessary, tracke may be cut
with a ne tooth saw.
• To maintain interchangeability of track to allow
future replacement in the eld, the screws adhered
in the track to the header in the pocket side must be
backed out one half turn after seating the track.
MOUNT DOOR HARDWARE
3
• Place quick release top mount plates
on top of each door at the distance
shown from the outside edge.
• Using brackets as a template, drill
3/32" diameter holes and secure
with (#8 x 1") screws.
• Secure door bumper as shown.
1"
(2,5 cm)
Rear
Arriére
Parte trasera
Center
Centre
Centro
5-1/2" (14 cm)
Front
Avant
Delantera
Loading...