Knape&Vogt BYP-75AFW User Manual [fr, en, es]
SLIDING DOOR HARDWARE - BY PASS
BYP-60AFW & BYP-75AFW • For 2 or 3 doors up to 60 lbs. (single wheel)
& 75 lbs. (twin wheel) each with thickness of 1-3/8"
Tools Required • Outils requis • Herramientas requeridos
Drill (3/32") • Perceuse (3/32") • Taladro (3/32")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
Flat Head Screw Driver • Tournevis à tête plate • Destornillador de cabeza plana
CONTENTS 2-Door 3-Door
#310289_B (1112)
Assembly
Instructions
A. Track 1 1
B. Carrier B Offsets 4 6
C. Pull 2 3
D. Floor Guide 1 2
E. #8 x 3/4" Phillips Pan Head Screw 13 26
F. #8 x 1-1/4" Phillips Pan Head Screw 7 14
G. Door Stop 1 1
B.
OR
C.
E.
F. G.
QUINCAILLERIE POUR PORTE COULISSANTE – BY PASS
BYP-60AFW & BYP-75AFW • Pour 2 à 3 portes jusqu'à 27,2 kg (roue simple)
y 34 kg (roue jumele) chacune d'une épasseur de 3,5 cm
CONTENU 2-Portes 3-Portes
A. Coulisse 1 1
B. Supports a rouleaux décalés B 4 6
C. Poignée 2 3
D. Guide de porte 1 2
E. #8 x 3/4" Vis Phillips 13 26
tête cylindrique
CONTENU 2-Portes 3-Portes
F. #8 x 1-1/4" Vis Phillips 7 14
tête cylindrique
G. Butoir 1 1
A.
D.
#310289_B (1112)
Instructions
d’assemblage
#310288_B (0912)
HERRAJE PARA PUERTA CORREDIZA - TIPO BY PASS
BYP-60AFW & BYP-75AFW • Para 2 o 3 puertasde hasta 27,2 kg (sola rueda)
y 34 kg (rueda doble) cada una y de 3,5 cm de grosor
CONTENIDO 2-Puertas 3-Puertas
A. Caril 1 1
B. Offsets del portador B 4 6
C. Deslizador 2 3
D. Guía del piso 1 2
E. #8 x 3/4" Tornillos Phillips 13 26
de cabeza chaneada
CONTENIDO 2-Puertas 3-Puertas
F. #8 x 1-1/4" Tornillos Phillips 7 14
de cabeza chaneada
G. Tope de la puerta 1 1
#310289_B (1112)
Instrucciones para
el ensamblaje
SLIDING DOOR HARDWARE - BY PASS
PREPARE OPENING
1
Hmax = Door Height + 1-7/8" • Hmin = Door Height + 1-1/2"
2-Door Width = 2 x Door Width - 1"
#310289_B (1112)
Assembly
Instructions
3-9/16"
(9 cm)
1-1/8" - 1-3/8"
(2,9 cm - 3,5 cm)
3-Door Width = 3 x Door Width - 2"
MOUNT FRAME HARDWARE
2
• Center track in opening.
• Using track as template, mark
screw locations.
• Drill 3/32" pilot holes and
secure with (#8 x 1-1/4") screws.
Note: If necessary, track may be cut
with a fine tooth saw.
Opening Height
Hauteur Ouverture
Altura Abertura
Door Height
Hauteur Porte
Altura Puerta
3/8" - 1/2"
(1 cm - 1,3 cm)
MOUNT DOOR HARDWARE
3
• Place carriers on back
of each door at the distance
shown from the outside
edge for your model.
• Using carriers as
a template, drill 3/32"
diameter holes and
secure with (#8 x 3/4")
screws
• Drill 2-1/8" diameter hole
approximately 1/4"
deep on outside edge
of each door as
shown to mount
pulls.
36"
(91,4 cm)
2" (5,1 cm)
1/2"
(1,3 cm)
1/2"
(1,3 cm)
Left Edge
Bord gauche
Borde izquierdo
Both Sides
Deux côtés
Ambos lados
OR
1-3/16"
(3 cm)
Right Edge
Bord droit
Borde derecho
Loading...