Knape&Vogt BYP-60AFS3 User Manual [fr, en, es]
SLIDING DOOR HARDWARE - BY PASS
BYP-60AFR/BYP-60AFS/BYP-60AFS3 • For 2 or 3 doors up to 60 lbs. each
with thickness of 1-3/8"
Tools Required • Outils requis • Herramientas requeridos
Drill (3/32") • Perceuse (3/32") • Taladro (3/32")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
Flat Head Screw Driver • Tournevis à tête plate • Destornillador de cabeza plana
Tape Measure • Ruban à mesurer • Cinta métrica
1-3/4" Forstener Bit • 1-3/4" pointe Forstener • Broca Forstner de 1-3/4"
CONTENTS 2-Door 3-Door
#310299_C (1013)
Assembly
Instructions
A. Track 1 1
B. Carrier B Offsets 4 6
C. Pull 2 3
D. Door Guide 1 2
E. #8 x 3/4" Phillips Pan Head Screw 13 26
F. #8 x 1-1/4" Phillips Pan Head Screw 7 14
G. Door Stop 1 1
B.
D.
E.
C.
BYP-60AFS
BYP-60AFS3
F.
BYP-60AFR
A.
OR
QUINCAILLERIE POUR PORTE COULISSANTE – BY PASS
BYP-60AFR/BYP-60AFS/BYP-60AFS3 • Pour 2 à 3 jusqu'à 27,2 kg chacune d'une
épasseur de 3,5 cm
CONTENU 2-Portes 3-Portes
A. Rail 1 1
B. Contrebalancements de partie 4 6
portante B
C. Tirer 2 3
D. Guide de Porte 1 2
CONTENU 2-Portes 3-Portes
E. #8 x 3/4" Vis Phillips tête cylindrique 13 26
F. #8 x 1-1/4” Vis Phillips tête cylindrique 7 14
G. Buttoir de porte 1 1
OR
G.
#310299_C (1013)
Instructions
d’assemblage
HERRAJE PARA PUERTA CORREDIZA - TIPO BY PASS
BYP-60AFR/BYP-60AFS/BYP-60AFS3 • Para 2 o 3 puertasde hasta 27,2 kg cada
una y de 3,5 cm
CONTENIDO 2-Puertas 3-Puertas
A. Carril 1 1
B. Vástagos del mecanismo de arrastre B 4 6
C. Tirador 2 3
D. Guía de la puerta 1 2
CONTENIDO 2-Puertas 3-Puertas
F. #8 x 3/4" Tornillos Phillips 13 26
de cabeza chaneada
F. #8 x 1-1/4” Tornillos Phillips 7 14
de cabeza chaneada
G. Tope de la puerta 1 1
#310288_B (0912)
#310299_C (1013)
Instrucciones para
el ensamblaje
SLIDING DOOR HARDWARE - BY PASS
PREPARE OPENING
1
Hmax = Door Height + 2-1/16" • Hmin = Door Height + 1-5/8"
#310299_C (1013)
Assembly
Instructions
3-1/2"
(8,9 cm)
2-Door Width = 2 x Door Width - 1"
3-Door Width = 3 x Door Width - 2"
MOUNT FRAME HARDWARE
2
• Center track in opening.
• Using track as template, mark
screw locations.
• Drill 3/32" pilot holes and secure
with (#8 x 1-1/4") screws. (F)
Opening Height
Hauteur Ouverture
Altura Abertura
1-1/4" - 1-9/16"
(3,2 cm - 4 cm)
Door Height
Hauteur Porte
Altura Puerta
3/8" - 1/2"
(1 cm - 1,3 cm)
Note: If necessary, track may be
cut with a fine tooth saw.
MOUNT DOOR HARDWARE
3
• Place carriers on back of each
door at the distance shown.
• Using carriers as a template,
drill 3/32" holes and secure
with (#8 x 3/4") screws. (E)
• Drill 2-1/8" diameter hole
approximately 1/4" deep
on outside edge of each
door as shown to mount pulls.
36"
(91,4 cm)
Left Edge
Bord gauche
Borde izquierdo
1/2"
(1,3 cm)
1-3/16"
(3 cm)
Right Edge
Bord droit
Borde derecho
2" (5,1 cm)
Loading...