Knape&Vogt BYP-100A User Manual [en, fr, es]
SLIDING DOOR HARDWARE - BY PASS
BYP-75A & BYP-100A • For 2 doors up to 75 lbs. (1572-QR carrier)
& 100 lbs. (1606-QR carrier) each with thickness of 1-3/8" to 1-3/4"
Tools Required • Outils requis • Herramientas requeridos
Wrench (included) • Clé (incluse) • Llave (incluida)
Drill (3/32", 3/16", 3/8") • Perceuse (3/32", 3/16", 3/8") • Taladro (3/32", 3/16", 3/8")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
Tape Measure • Ruban à mesurer • Cinta métrica
Spade Bit (7/8") • Partie en angle (7/8") • Broca con punta de lanza (7/8")
CONTENTS 2-Door
A. Track 1
B. Carrier 4
C. Quick Release Top Mount Plate 4
D. Pull 2
E. Door Guide 1
F. #8 x 5/8" Truss Head Screw 16
G. #8 x 3/4" Pan Head Screw 2
H. #8 x 1-1/2" Pan Head Screw 3
I. #8 x 1" Pan Head Screw 16
J. Door Stop 1
B.
OR
D.
E.
#310302_B (1013)
Assembly
Instructions
C.
G.
F.
H.
A.
J.
I.
QUINCAILLERIE POUR PORTE COULISSANTE – BY PASS
BYP-75A & BYP-100A • Pour 2 portes jusqu'à 34 kg (1572-QR rouleaux décalés)
y 45,3 kg (1606-QR rouleaux décalés) chacune d'une épasseur de 3,5 cm à 4,4 cm
CONTENU 2-Portes
A. Rail 1
B. Partie portante 4
C. Plaque supérieure à relâchement rapide 4
D. Tirer 2
E. Guide de Porte 1
CONTENU 2-Portes
F. #8 x 5/8" Vis a tête bombée 16
G. #8 x 3/4" Vis tête cylindrique 2
H. #8 x 1-1/2" Vis a tête bombée 3
I. #8 x 1" Vis a tête bombée 16
J. Buttoir de porte 1
HERRAJE PARA PUERTA CORREDIZA - TIPO BY PASS
BYP-75A & BYP-100A • Para 2 puertasde hasta 34 kg (1572-QR portador)
y 45,3 kg (1606-QR portator) cada una y de 3,5 cm à 4,4 cm de grosor
CONTENIDO 2-Puertas
A. Carril 1
B. Mecanismo de arrastre 4
C. Placa para montaje superior de liberación rápida 4
D. Tirador 2
E. Guía de la puerta 1
CONTENIDO 2-Puertas
F. #8 x 5/8" Tornillo de cabeza de armazón 16
G. #8 x 3/4" Tornillos cabeza plana 2
H. #8 x 1-1/2" Tornillos cabeza plana 3
I. #8 x 1" Tornillos cabeza plana 16
J. Tope de la puerta 1
Instrucciones para
#310302_B (1013)
Instructions
d’assemblage
#310302_B (1013)
el ensamblaje
SLIDING DOOR HARDWARE - BY PASS
#310302_B (1013)
Assembly
Instructions
PREPARE OPENING
1
1
1572-QR (BYP-75)
Hmax = Door Height + 2-3/8"
Hmin = Door Height + 1-7/8"
1606-QR (BYP-100)
Hmax = Door Height + 2-1/2"
Hmin = Door Height + 2-1/8"
MOUNT FRAME HARDWARE
2
• Center track in opening.
• IMPORTANT: Place hangers loose
into track before securing.
• Using track as template, mark
screw locations.
• Drill 3/32" pilot holes and
secure with (#8 x 5/8") screws. (F)
2-Door Width = 2 x Door Width - 1"
Opening Height
Hauteur Ouverture
Altura Abertura
1572-QR (BYP-75):
1-1/2" - 1-7/8"
(3,8 cm - 4,8 cm)
1606-QR (BYP-100):
1-3/4" - 2"
(4,4 cm - 5,1 cm)
Door Height
Hauteur Porte
Altura Puerta
3/8" - 1/2"
(1 cm - 1,3 cm)
Note: If necessary, track may be
cut with a fine tooth saw.
MOUNT DOOR HARDWARE
3
• Place quick release top mount plates on
top of each door at the distance shown
from the outside edge.
• Using brackets as a template,
drill 3/32" diameter holes and secure
with (#8 x 1") screws. (I)
• Drill 7/8" diameter hole
approximately 1/4" deep
on outside edge of each
door as shown to mount pulls.
36"
(91,4 cm)
2" (5,1 cm)
9/16"
(1,4 cm)
Loading...