Knape&Vogt BIF-50A User Manual [en, fr, es]
SLIDING DOOR HARDWARE - BI-FOLD
BIF-50ND • For 2 or 4 doors up to 50 lbs. each with thickness of 3/4" to 1-1/8"
Tools Required • Outils requis • Herramientas requeridos
Wrench (included) • Clé (incluse) • Llave (incluida)
Drill (1/16", 3/32", 3/8") • Perceuse (1/16", 3/32", 3/8") • Taladro (1/16", 3/32", 3/8")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Tape Measure • Ruban à mesurer • Cinta métrica
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
Track (BK-1599-X or BK-1601-X - not included)
Coulisse (BK-1599-X or BK-1601-X - non incluses)
Carril (BK-1599-X or BK-1601-X - no incluidos)
CONTENTS 2-Door 4-Door
A. Narrow Hinge 3 6
B. Top Pivot Plate 1 2
C. Narrow Top Mount Plate 1 2
D. Narrow Bottom Guide Plate 1 2
E. Bottom Adjusting Bolt 1 2
F. Track Pivot Bracket 1 2
G. 4-Wheel Carrier 1 2
H. Jamb Bracket 1 2
I. Wood Knob 1 2
J. Snubber 1 2
K. Aligner - 2
L. #8 x 1-3/4" Pan Head Screw 1 2
M. #8 x 1" Pan Head Screw 16 36
N. #8 x 3/4" Flat Head Screw 3 6
O. #6 x 7/8" Flat Head Screw 24 36
P. #8 x 3/4" Pan Head Screw - 4
A.
G.
F.
K.
B.
H.
L.
C.
I.
QUINCAILLERIE POUR PORTE COULISSANTE – PLIANTE
BIF-50ND • Pour 2 à 4 portes jusqu’à 22,7 kg chacune d’une épaisseur de 1,9 cm à 2,9 cm
#310298_C (1013)
Assembly
Instructions
D.
E.
J.
N.
M.
P.
O.
#310298_C (1013)
Instructions
d’assemblage
CONTENU 2-Portes 4-Portes
A. Penture étroite 3 6
B. Plaque du pivot supérieur 1 2
C. Plaque de montage supérieure étroite 1 2
D. Plaque guide inférieure étroite 1 2
E. Verrou d'ajustement inférieur 1 2
F. Support de pivot de rail 1 2
G. Partie portante avec 4 roues 1 2
H. Support de montant 1 2
CONTENU 2-Portes 4-Portes
I. Pommeau de bois 1 2
J. Amortisseur 1 2
K. Aligner - 2
L. #8 x 1-3/4" Vis tête cylindrique 1 2
M. #8 x 1" Vis tête cylindrique 16 36
N. #8 x 3/4" Vis à tête plate 3 6
O. #6 x 7/8" Vis à tête plate 24 36
P. #8 x 3/4" Vis tête cylindrique - 4
HERRAJE PARA PUERTA DE CORREDERA PLEGABLE
– DE DOS HOJAS
BIF-50A & BIF-50S • Para 2 o 4 puertas de hasta 22,7 kg cada una y de 1,9 cm à 2,9 cm de grosor
CONTENIDO 2-Puertas 4-Puertas
A. Bisagra angosta 3 6
B. Placa del pivote superior 1 2
C. Placa angosta para montaje superior 1 2
D. Placa de guía inferior angosta 1 2
E. Perno de ajuste inferior 1 2
F. Soporte del pivote del carril 1 2
G. Mecanismo de arrastre de 4 ruedas 1 2
H. Soporte de jamba 1 2
CONTENIDO 2-Puertas 4-Puertas
I. Tirador de madera 1 2
J. Amortiguador 1 2
K. Alineador - 2
L. #8 x 1-3/4" Tornillos cabeza chaneada 1 2
M. #8 x 1" Tornillos cabeza chaneada 16 36
N. #8 x 3/4" Tornillos cabeza plana 3 6
O. #6 x 7/8" Tornillos cabeza plana 24 36
P. #8 x 3/4" Tornillos cabeza chaneada - 4
Instrucciones para
#310298_C (1013)
el ensamblaje
SLIDING DOOR HARDWARE - BI-FOLD
PREPARE OPENING
1
2-Door Width = 2 x Door Width + 9/16"
Hmax = Door Height + 3-3/4" • Hmin = Door Height + 2-1/8"
Pivot / PivoteGuide / Guía
4-Door Width = 4 x Door Width + 1"
Opening Width
Largeur d'ouverture
Ancho de la apertura
Opening Height
Hauteur Ouverture
Altura Abertura
#310298_C (1013)
Assembly
Instructions
1-3/8" - 1-7/8"
(4,1 cm - 4,8 cm)
Door Height
Hauteur Porte
Altura Puerta
3/4" - 1-7/8"
(1,9 cm - 4,8 cm)
Pivot
Pivote
2-Door: Line up track ush against jamb on guide door side.
4-Door: Center track in opening.
5/8"
(1,6 cm)
Guide
Guía
MOUNT FRAME HARDWARE
2
• Using track as a template, mark
screw locations.
• IMPORTANT: Place track pivot and
hangers loose into track before
securing.
• Drill 3/32" pilot holes and secure
with (#8 x 1") screws. (M)
• Locate top pivot bracket so center of
pivot slot is approximately 2-1/8" from
side jamb and hand tighten in place.
• Center jamb bracket directly
below track in jamb corner.
• Using jamb bracket as a template,
drill 3/32" pilot holes and secure
with (#8 x 3/4") screws. (N)
Note: Track length should be at least 1/8" less than the width of the finished opening. If necessary, track may be cut with a fine tooth saw.
When the finished opening is taller than door height, the jamb bracket may be fastened to the side jamb making certain that the screws are
secured in a solid material. Blocking underneath the jamb bracket is required to support the door weight.
MOUNT DOOR HARDWARE
3
• Using top plates as a template, drill 3/32" diameter
pilot holes and secure with (#8 x 1")
screws* (M) so that the pivot is in
locations shown.
• Using bottom plate as a template, drill
3/8" clearance holes (as shown) and
3/32" diameter pilot holes and secure
with (#8 x 1") screws (M) with plate
edge ush to door edge.
• Thread bottom adjusting bolt into place.
• To install hinges, place doors side by side as folded
with 1/16" gap.
• Use hinge as template, drill 1/16" diameter pilot
holes and secure with (#6 x 7/8") screws. (O)
• Drill 3/16" diameter hole through guide door at
center of width and secure knob with (#8 x 1-3/4") screws. (L)
*Note: Top carrier plate is mounted 1-1/4" from door edge for 2
and 4-door. Plate is mounted 1-3/4" for multiple fold doors.
2-1/8"
(5,4 cm)
1-1/4"
(3,2 cm)
4-Door Only
4 portes seulement
Solo para 4 puertas
Centered
Centré
Centrado
4.5"
(11,4 cm)
Loading...