Knape&Vogt BIF-30S User Manual [en, fr, es]
SLIDING DOOR HARDWARE - BI-FOLD
BIF-30 • For 2 or 4 doors up to 30 lbs. each with thickness of 3/4" to 1-3/4"
Tools Required • Outils requis • Herramientas requeridos
Drill (1/16", 3/32", 3/16", 3/8") • Perceuse (1/16",3/32", 3/16", 3/8") • Taladro (1/16",3/32", 3/16", 3/8")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
Tape Measure • Ruban à mesurer • Cinta métrica
CONTENTS 2-Door 4-Door
A. Hinge 3 6
B. Top Roller Guide 1 2
C. Bottom Pivot 1 2
D. Track 1 1
E. Track Pivot 1 2
F. Jamb Bracket 1 2
G. Wood Knob 1 2
H. Snubber 1 1
I. #8 x 1-3/4" Pan Head Screw 1 2
J. #6 x 1-1/4" Flat Head Screw 4 8
K. #8 x 3/4" Pan Head Screw 6 16
L. #6 x 7/8" Flat Head Screw 12 24
M. Top Pivot 1 2
N. Aligner - 2
A.
B.
D.
K.
#310294_E (1013)
Assembly
Instructions
C.
E.
G.
I.
L.
J.
H.
N.M.
F.
QUINCAILLERIE POUR PORTE COULISSANTE – PLIANTE
BIF-30 • Pour 2 à 4 portes jusqu’à 13,6 kg chacune d’une épaisseur de 1,9 cm à 4,4 cm
CONTENU 2-Portes 4-Portes
A. Penture 3 6
B. Guide de roues supérieur 1 2
C. Pivot inférieur 1 2
D. Rail 1 1
E. Pivot du rail 1 2
F. Support de montant 1 2
G. Pommeau de bois 1 2
CONTENU 2-Portes 4-Portes
H. Amortisseur 1 1
I. #8 x 1-3/4" Vis tête cylindrique 1 2
J. #6 x 1-1/4" Vis à tête plate 4 8
K. #8 x 3/4" Vis tête cylindrique 6 16
L. #6 x 7/8" Vis à tête plate 12 24
M. Pivot supérieur 1 2
N. Aligner - 2
QUINCAILLERIE POUR PORTE COULISSANTE – PLIANTE
BIF-30 • Pour 2 à 4 portes jusqu’à 13,6 kg chacune d’une épaisseur de 1,9 cm à 4,4 cm
CONTENIDO 2-Puertas 4-Puertas
A. Bisagra 3 6
B. Guía del rodillo superior 1 2
C. Pivote inferior 1 2
D. Carril 1 1
E. Pivote del carril 1 2
F. Soporte de jamba 1 2
G. Tirador de madera 1 2
CONTENIDO 2-Puertas 4-Puertas
H. Amortiguador 1 1
I. #8 x 1-3/4" Tornillos cabeza chaneada 1 2
J. #6 x 1-1/4" Tornillos cabeza plana 4 8
K. #8 x 3/4" Tornillos cabeza chaneada 6 16
L. #6 x 7/8" Tornillos cabeza plana 12 24
M. Guía de pivote superior 1 2
N. Alineador - 2
#310294_E (1013)
Instructions
d’assemblage
#310294_E (1013)
Instructions
d’assemblage
SLIDING DOOR HARDWARE - BI-FOLD
PREPARE OPENING
1
2-Door Width = 2 x Door Width + 1/2"
Hmax = Door Height + 2-5/8" • Hmin = Door Height + 1-3/8"
Pivot / PivoteGuide / Guía
#310294_E (1013)
Assembly
Instructions
5/8" - 1-1/8"
(1,6 cm - 1,3 cm)
1/8" Min.
(0,3 cm)
1/16"
(0,2 cm)
4-Door Width = 4 x Door Width + 7/8"
1/16"
5/16"
(0,8 cm)
MOUNT FRAME HARDWARE
2
• Using track as a template, mark
screw locations.
• Important: Place track pivot in track
before securing.
• Drill 3/32" pilot holes and secure
with (#8 x 3/4") screws. (K)
• Locate track pivot bracket in track
next to the jamb intended for pivot.
• Center jamb bracket directly
below track in jamb corner.
• Using jamb bracket as a template,
drill 1/16" pilot holes and secure
with (#6 x 1-1/4") screws. (J)
(0,2 cm)
1/8" Gap Min.
(0,3 cm)
5/16" Min.
(0,8 cm)
1/16"
(0,2 cm)
2-Door: Line up track ush against jamb on guide door side.
4-Door: Center track in opening.
Opening Height
Hauteur Ouverture
Altura Abertura
5/16"
(0,8 cm)
4-Door Only
4 portes seulement
Solo para 4 puertas
Door Height
Hauteur Porte
Altura Puerta
3/4" - 1-1/2"
(2,2 cm - 3,8 cm)
Note: Track length should be at least 1/8" less than the width of the finished opening. If necessary, track may be cut with a fine tooth saw.
When the finished opening is taller than door height, the jamb bracket may be fastened to the side jamb making certain that the screws are secured
in a solid material. A block underneath the jamb bracket is required.
Pivot
Pivote
1"
(2,5 cm)
Guide
Guía
36"
(91,4 cm)
1"
(2,5 cm)
Pivot
Pivote
MOUNT DOOR HARDWARE
3
• Drill 3/8" holes 1-1/4" deep in top and
bottom of the pivot door and top only of
guide door.
• Remove lower pivot screw, tap in pivots
and guides, replace screw.
• To install hinges, place doors side by
side as folded with 1/16" gap.
• Use hinge as template, drill 1/16"
diameter holes and secure with
(#6 x 7/8") screws. (L)
• Drill 3/16" diameter hole through guide
door at center of width and secure knob
with (#8 x 1-3/4") screw. (I)
1"
(2,5 cm)
4.5"
(11,4 cm)
Centered
Centré
Centrado
Loading...