Knape&Vogt BIF-125A User Manual [en, fr, es]
SLIDING DOOR HARDWARE - BI-FOLD
BIF-125A • For 2 or 4 doors up to125 lbs. each with thickness of 1-1/8" to 1-3/4"
Tools Required • Outils requis • Herramientas requeridos
Wrench (included) • Clé (incluse) • Llave (incluida)
Drill (3/32", 3/16", 3/8") • Perceuse (3/32", 3/16", 3/8") • Taladro (3/32", 3/16", 3/8")
Phillips Screw Driver • Tournevis Phillips • Destornillador Phillips
Fine Tooth Saw (optional) • Scie à dents nes (optionnelle) • Sierra de dientes nos (opcional)
CONTENTS 2-Door 4-Door
#310297_D (0113)
Assembly
Instructions
A. Track Pivot Bracket 1 2
B. Top Pivot Plate 1 2
C. Quick Release Top Mount Plate 1 2
D. Bottom Door Plate 1 2
E. Bottom Adjusting Screw 1 2
F. Track 1 1
G. Floor Plate 1 2
H. 4-Wheel Ball Bearing Carrier 1 2
I. Snubber 1 2
J. #8 x 3/4" Pan Head Screw - 4
K. #8 x 1-1/2" Pan Head Screw 25 42
L. Pair of Aligners - 1
A.
B.
E.
G.
F.
C.
H.
K.
QUINCAILLERIE POUR PORTE COULISSANTE – PLIANTE
BIF-125A • Pour 2 à 4 portes jusqu’à 56,7 kg chacune d’une épaisseur de 2,9 cm à 4,4 cm
CONTENU 2-Portes 4-Portes
A. Support de pivot de rail 1 6
B. Plaque du pivot supérieur 1 2
C. Plaque du pivot supérieur 1 2
D. Plaque de montage supérieure 1 2
à dégagement rapide
E. Vis d’ajustement inférieure 1 2
F. Coulisse 1 1
CONTENU 2-Portes 4-Portes
G. Plaque de plancher 1 2
H. Chariot à 4 roulettes à roulement à billes 1 2
I. Butée de n de course 1 2
J. #8 x 3/4" Vis tête cylindrique - 4
K. #8 x 1-1/2" Vis tête cylindrique 25 42
L. Paire d’aligneurs - 1
D.
I.
J.
L.
#310297_D (0113)
Instructions
d’assemblage
HERRAJE PARA PUERTA DE CORREDERA PLEGABLE
– DE DOS HOJAS
BIF-125A • Para 2 o 4 puertas de hasta 56,7 kg cada una y de 2,9 cm a 4,4 cm de grosor
CONTENIDO 2-Puertas 4-Puertas
A. Soporte del pivote del carril 1 2
B. Placa del pivote superior 1 2
C. Placa de montaje superior 1 2
fácilmente desmontable
D. Puerta inferior placa 1 2
E. Tornillo de ajuste inferior 1 2
F. Carril 1 1
CONTENIDO 2-Puertas 4-Puertas
G. Placa de piso 1 2
H. Soporte del pivote del carril 1 2
I. Placa del pivote superior 1 2
J. #8 x 3/4" Tornillos cabeza chanfleada - 4
K. #8 x 1-1/2" Tornillos cabeza chanfleada 25 42
L. Tornillo de ajuste inferior - 1
#310297_D (0113)
Instrucciones para
el ensamblaje
#310297_D (0113)
SLIDING DOOR HARDWARE - BI-FOLD
PREPARE OPENING
1
2-Door Width = 2 x Door Width + 9/16"
1/8" Min.
(0,3 cm)
4-Door Width = 4 x Door Width + 1”"
3/8"
(1 cm)
Note: When using optional roller guide and bottom channel, use doorway height plus 3-1/2" when bottom guide channel is mounted
recessed, flush with finished floor. Use doorway height plus 4-1/8" if bottom guide channel is surface mounted.
MOUNT FRAME HARDWARE
2
• Using track as a template, mark
screw locations.
• IMPORTANT: Place track pivot and
hangers loose into track before
securing.
• Drill 3/32" pilot holes and secure
with (#8 x 1-1/2") screws.
• Locate top pivot bracket so center of
pivot slot is approximately 2-1/8"
from side jamb and hand tighten in place.
• Center bottom bracket directly below track
in jamb corner.
• Using oor plate as a template, drill
3/32" pilot holes and secure with
(#8 x 1-1/2") screws in slots only.
1/16"
(0,2 cm)
Multiple Fold Doors Width: Door Width + 9/16" (for pivot pair)
+ 3/8” (for each additonal pair)
Hmax = Door Height + 5-1/4" • Hmin = Door Height + 3-7/16"
1/16"
(0,2 cm)
1/8" Gap Min.
(0,3 cm)
1/16"
(0,2 cm)
2-Door: Line up track flush against jamb on guide door side.
4-Door: Center track in opening.
3/8" Min.
(1 cm)
(1 cm)
Opening Height
Hauteur Ouverture
Altura Abertura
3/8"
Assembly
Instructions
2-7/16" - 3-1/4"
(6,2 cm - 8,3 cm)
Door Height
Hauteur Porte
Altura Puerta
1" - 2"
(2,2 cm - 3,8 cm)
4-Door Only
4 portes seulement
Solo para 4 puertas
Note: When the finished opening is taller than max opening height, the floor plate may be fastened to a riser block
placed under the floor plate. The riser must be secured to the floor.
Pivot
Pivote
1-3/4"
(4,4 cm)
MOUNT DOOR HARDWARE
3
• Using top plates as a template, drill 3/32"
diameter holes and secure with (#8 x 1-1/2") screws*
so that the center of pivot is in locations shown.
• Using bottom plate as a template, drill 3/8"
clearanace hole 1-3/4” deep as shown and 3/32"
diameter holes and secure with (#8 x 1-1/2") screws.
• Thread bottom adjusting bolt into place.
• ATTACH HINGES. (purchased separately)
• ATTACH KNOB. (purchased separately)
*Note: Top carrier plate is mounted 1-1/4" from door edge for
2 and 4-doors. Plate is mounted 1-3/4" for multiple fold doors.
1-3/4"
(4,4 cm)
Guide
Guía
1-3/4"
(4,4 cm)
Pivot
Pivote
(15,2 cm)
Centered
Centré
Centrado
6"
Loading...