KMC Controls FlexStat Quick Reference Guide
Controller/Sensor/Thermostat
Quick Reference Guide
FlexStat
Home Screen
WED 9/3 5:43 PM
COOL:
OCC:
FAN:
HUM: 31%RH
Override Screens
SYSTEM MODE
SYSTEM ENABLE:
OCCUPANCY OVERRIDE
OCC OVERRIDE:
FAN MODES
UNOCC:
OCC: AUTO
AUTO
OFF
AUTO
Setpoint Adjustment
Up (Setpoint)
Override
Left
(Override)
Down (Setpoint)
Navigation
Navigate the menus and change seings by pressing a combination of various arrow buons and the
(center round) Enter buon. Push the:
Configuration Screens
MAIN MENU
ABOUT
ADVANCED
ALARM
DATE/TIME
SCHEDULE
SETPOINTS
SYSTEM
Right
Configuration
(Menu)
SCHEDULE
ENTIRE WEEK [MON–SUN]
WEEKDAYS [MON–FRI]
WEEKEND [SAT–SUN]
INDIVIDUAL DAYS
HOLIDAYS
ENTIRE WEEK
7:30:00 AM ON
1:
2: 5:15:00 PM OFF
3:
4:
5:
6:
[—>] DELETES ENTRY
Room Temperature Setpoint Adjustment
From the Home (temperature display) screen, press
the Up or Down arrow buon once to view the existing setpoint.
• Enter buon to select and/or exit value editing.
• Up or Down buon to move among entries.
• Right or Left buon to move among value elds.
To temporarily change the setpoint, press the Up
or Down arrow buon repeatedly until the desired
seing is displayed and press Enter. (If Enter is not
pressed, the display will return to the Home screen
after about ten seconds and the new setpoint value
• Left buon to return to the Home screen.
NOTE: Access to various functions may require a
password.
NOTE: See the FlexStat Operation Guide for
complete details on FlexStat conguration.
will still be saved.) The new setpoint will hold until
the next schedule change.
To permanently change the setpoint for occupied
mode, go to the Setpoints section under the Main
Menu. (In the Setpoints menu, heating/cooling setpoints/setbacks and deadband can be changed with,
if required, the correct password access.)
FlexStat 1 Quick Reference Guide
Heat/Cool, Fan, Occupancy, and Override
5. Enter to exit value editing.
When the fan is commanded to run, the animated
FAN icon on the display rotates (if programmed to).
When the fan command stops, the fan icon is motionless.
The OCC icon shows a sun when in Occupied mode
and a quarter moon when in Unoccupied mode.
HEAT or COOL will show (and be animated when
there is an active command to move the room temperature toward the setpoint via mechanical heating/
cooling or an economizer), depending on the current
mode. This can also be turned OFF.
To override these modes from the Home (temperature display) screen, press the Left arrow buon.
Press Up or Down to get to the desired line and then
Enter (twice) to edit the mode seing. Press Left to
exit to Home.
Main Menu and Settings
From the Home (temperature display) screen, press
the Right arrow buon to enter the Main Menu.
NOTE: Seings and adjustments may require a
password.
Schedules
SCHEDULE
ENTIRE WEEK [MON–SUN]
WEEKDAYS [MON–FRI]
WEEKEND [SAT–SUN]
INDIVIDUAL DAYS
HOLIDAYS
ENTIRE WEEK
1:
7:30:00 AM ON
2: 5:15:00 PM OFF
3:
4:
5:
6:
[—>] DELETES ENTRY
6. Left to move back to days or back one page.
NOTE: If a day of a week (e.g., Friday) has a
dierent schedule than the rest, using the
Weekdays menu rst and then modifying
that one day in the Individual Days menu
may be easier (two entries) than entering
schedules for each day separately in the
Individual Days menu (ve entries).
NOTE: The last overlapping entry overrides
any other. For example, suppose the
WEEKDAYS menu is used to set all
weekdays for 7:00 AM ON and 5:00 PM
OFF, and then the INDIVIDUAL DAYS
menu is used to add some additional
evening meeting ON times for Tuesday
and Wednesday. If the WEEKDAYS menu
is later used to change the ON time from
7:00 to 7:15, schedules for all the individual
week days will be reset to conform to
what appears in the WEEKDAYS menu
and any special times for individual days
will be erased. (Special day schedules will
then need to be added again through the
INDIVIDUAL DAYS menu).
The Holiday entries will override the normal
occupied weekly schedule entries and keep those
days’ seings at their setback values. (Setback values
are entered in the Setpoints section of the Main
Menu.)
HOLIDAYS
HOL1:
JAN 1 2009
HOL2: MAR 21 2009
HOL3: MAY 26 2009
HOL4: JULY 4 2009
HOL5: SEPT 1 2009
HOL6: NOV 27 2009
HOL7: NOV 28 2009
The factory default schedule is always occupied
(ON). To modify the schedule for mixed occupied
NOTE: See the FlexStat Operation Guide for more
operation details.
(ON) and unoccupied (OFF) times, select Schedules
in the Main Menu and press:
1. Right/Left to move among days and Enter to
select.
KMC Controls, Inc.
19476 Industrial Drive
2. Up/Down to move among entries and Enter to
select and edit.
New Paris, IN 46553
574.831.5250
3. Right/Left to move among value elds.
4. Up/Down to increment/decrement value.
© 2014 KMC Controls, Inc. 913-019-06C
FlexStat 2 Quick Reference Guide
(Specifications, design, and operation are subject to change without notice)
www.kmccontrols.com
info@kmccontrols.com
Loading...