K&M 21460.177.67, 21460.177.55 Users Guide

SAFETY INSTRUCTIONS
MOUNTING INSTRUCTIONS
Make sure all parts are there and in proper condition: A. adaptor sleeve, B. stand, C. locking knobs 2x The mounting of the 214/6 is easy to handle (1) screw-in both locking knobs (2) loosen the locking knob on the base clamp (3) spread legs apart to max. base width (4) braces should come into a horizontal position (5) tighten locking knob 2
(5) NOTE: (5) Do not over tighten the locking knobs. (5) This will result in undue stress to the fitting. (5) Just enough to hold the extensions position firmly.
SPECIFICATIONS
Thank you for choosing this product. This instruction manual informs you about the important steps to set up and handle the product. We recommend to keep the manual in a place for a possible later use.
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
21460-177-55/76 Rev.12/07 03-80-707-00 3/20
a. Load capacity: max. 110 lbs* b. before use:
- check the functional capability of: K&M-stand, speakers
- and tools concerning: completeness, integrity, usability
- choose only trained installers (2 persons with
- professional and physical qualification)
c. optimal stability conditions:
- use only on even and stable surface
- avoid off-center loading
- set up brace 4 in horizontal position d. safety in operation:
- unauthorized persons should keep distance to protect
- from stumble and tilting
- inspect bolted assemblies regularly
- always insert the safety pin after positioning of the speaker
- do not push and pull the loaded stand on the floor; it can
- cause damages on the base
e. safety in maintaining and removing
- first remove load
- pay attention to possible hazards (squeezing, hurting)
- by collapsing
214/6 Speaker Stand
- load capacity: 110 lbs*
- professional, solid, transportable
- Height: min. 55" / max. 86"; foot circle: 52"; extension ø 1-3/8" and 1-1/2"; weight: 9.7 lbs
Material
baserods: Alu extension, braces, locking pin: steel clamps: zinc die-cast adaptor sleeve: (PA) foot rubbers: (TPE)
Load capacity max. 110 lbs*
Dimensions
foot circle: diameter 52" height: 55 - 86" (by max.foot circle)
extension: diameter 1-3/8" and 1-1/2" Collapsed, kg 46 x 6 x 5", 9.7 lbs Card box, kg 47 x 5 x 5", 11.4 lbs
Accessories (optional)
bag 21311 (for one or two 21460)
K&M-flange adaptor (e.g. 19580, 19656)
K&M-screw-on-adaptor 24281
* With centric loading, on a horizontal surface and without lateral
forces (wind, shocks etc.)
ATTACHING & MOVING of the LOAD
- NOTE! Do not undervalue the weight of the load.
- Attaching and moving of the load should be done
- by trained installers
- While moving the load hold the extension in a
- safe and firm way.
- Secure the extension with the locking pin.
- NEW: the extension ends in a cone.
- NEW: This would be helpful to attach the load.
MAINTENANCE
MOVING
Involved Persons: FI - First Installer: holds the loaded extension
SI - Second Installer: handles locking knob and locking pin
Action: FI 1 holds the extension firmly
SI 2 loosens the locking knob 3 pulls the head of the locking
6 pin until the extension is 6 able to move
FI 4 lifts the extension in
7 desired height 7 NOTE: for easier finding of 7 the pin hole this hole should 7 be seen for a moment above 7 the clamp
SI 5 unhands the head of the
8 locking pin so it´s able to 8 atch into the hole of the 8 extension
FI 6 lowers the extension
9 slowly until the locking 9 pin is latching into the 9 hole
SI 7 tightens the locking knob
Remove the load in reverse order.
- Handle the stand with care.
- Maintain only in unloaded mode.
-For cleaning use a damp cloth and a non-abrasive cleaner.
(D) DEBUGGING & (R) REPAIR D: stand totters:
D: R: Arrange an even ground. D: R: Spread legs into max. width and tighten the locking knob
D: Extension totters and/or is running in:
D: R: Make sure that the locking pin is in work and tighten locking knobs.
Loading...