Klugmann KH9850 Instruction Manual
INSTRUCTION MANUAL
Hood
KH9850
Klugmann Hausgeraete GmbH.
Gropiusstraße 7,
48163 Münster, Deutschland
+49 (0)2501 - 963 5732
+49 (0)2501 - 963 1834
service@klugmann-hausgeraete.de
www.klugmann-hausgeraete.de
EN
WARNINGS AND SAFETY PRECAUTIONS
*This product is designed to be used
at home
*Operational power supply is AC 220240 Volts 50Hz.
*Your product has the earthed plug
cable.This cable must be connected
to AC power supply which is fully
grounded.
*All electrical wiring must be done by
a qualified electrician.
*Unauthorized installation can be work
in poor performance and damage to the
product and lead to accidents.
*Make sure the power cable is not
pinched and not crushed to during
installation. The power supply cable
must not pass near the stove.
It may be melting and cause a fire.
*Do not connect the unit to the power
supply unless the assembly of the
device is fully completed.
*In case of any danger,power off the
product easly accessible to ensure that
your plug.
*Do not touch the illumination lamps of
the device when they are used for
a long time.
*Flammable foods should not be cooked
under this device.
*Operate the Hood Fume after placing
the casserole and pan on the cooker.
Otherwise, in some parts of the device
may result deformed due to high
temperature.
*Out of the stove pots,pans and so on.
Turn off the stove before.
*Do not leave hot oil on the stove.
Spontaneously flammable in containers
with hot oil.
*Please be careful. Roast type, etc..
While food oils can ignite and cause fire
damage.
*Ensure the timely replacement or cleaning
of the filters.Accumulated on the filter is
a risk of fire due to the oil.
*Only use the metal filter provided with
the device and do not use other materials
to replace it.
*Do not operate the device without it’s filter.
Do not remove the metal filter of the device
while it is operating.
*In case of flare begin, turn off energy of
hoods and cookers.
*Hoods are made for home use while
cooking. If used for other purposes,
there is a risk of malfunction and
interests outside of warranty.
*About the evacuation of the outlet air,
Please follow the rules and guidelines
of the authorities.
*The cleaning of the device should be
implemented with periodic intervals.
*Turn off your device before maintenance
operations.
2
EN
*Electric hood and supplied with energy
other than electricity devices running at
the same time negative pressure in
the room 4 Pa ( 4 X 10 bars ) must not
exceed.
*Do not any connection to chimneys which
the stoves are connected, waste gasses
are exhausted or to chimneys which have
uprisings of the flames.
*When your product is 150mm or 120mm
diameter chimney connector pipe use.
The piping as short as possible and should
be less angled.
*Make sure your child play with the
product. Do not allow children to use the
product.
*As the packing materials of the device
may be harmful to children, keep them
out of reach of the children.
*Supply cord is damaged, in order to
avoid a dangerous situation, the
manufacturer or service or be replaced
by a qualified person equally.
*In case of flare begin, turn off energy of
hoods and cookers. Cover the top of the
flame. Never use water to extinguish..
*Accessible part of the cooking appliance
may be hot when running.
For your safety, extractor fan installation (max. of 6 Amp) fuse use.
Shipping and Handling Precautions regarding.
*All materials used in the packaging of your product which is suitable for recycling.
*Parcels during transport, the signs mentioned above must be followed.
*To move your product box located on the side of the lift grips Hand Piece.
If you need transportation;
*Please keep the original packaging.
*Move with the original packaging, handling marks on the packaging must be observed.
If there is no original package;
*Do not put weight on the device.
*Protect the outer surface of the blow.
DDaammaaggee ttoo tthhee pprroodduucctt bbyy ppaacckkaaggiinngg yyoouurr mmoovvee..
3
Standard Accessories
Picture 1
Min.55 cm
Min.65 cm
EN
Plastic adapter (Ø150mm/120mm)
Plastic adapter that plugs into the air outlet of the hood.
Picture-1
Device Location:
Upon completion of the installation of hoods,
electric stove of the product should be a minimum
distance of 65 cm. Gas and other fuel-fired
furnaces, the minimum distance between the
product should be 75cm. Figure-1
Figurel 1
Unpacking the device:
* Please check whether your device has a deformation.
* Shipping failures should be reported immediately to the shipping charge.
* Showing errors also must be notified to the seller.
*Do not allow children to play with packaging material !!!
HOOD ASSEMBLY
M4x20
M5x10
Picture 2
Metal bracket to mount the hood:
Items to hang on the wall has the (L) form 2 pieces metal
bracket to mount.This sheet with set screws for ease of
packing is given. Product before you hang this sheet is
located on the cabinet with M5 screw fastening nuts and
bolts M5x10. Picture-2
4
Picture 3
Picture 4
EN
Be nailed to the wall dowels
8 mm dowels for hanging screws (A, B, C) into the holes you
drilled. To connect the chimney mounting plate. 7 mm 2 pieces
dowels into the holes you drilled with the Ø7mm. Picture-3
Chimney mounting bracket on the wall where you place (Ø7) to
dowels, 3,9 x22 with a screw mount.
Picture-4
Hanger of the screws to be screwed
AA
BB
Picture 5
Resim 6
Picture 6
Resim 6
The wall that you have age 8 mm dowel (A, B) hanger screws,
screw with 5x50. 5 mm distance between the screw head and
the wall must remain. Picture-5
Screwing Hanger Bracket:
The age of the wall that you have to Ø 8 mm dowel
screw mounts and set the measure. 5mm distance between
the screw head and the wall must remain. Picture-6
Hang on the wall of the cooker hood:
Hold the body of the hood. Previously that
connect the hood to cabinet (L) in the form
of sheets hang from points A and B on
the wall. Figure-2
Ø8
Vertical Positioning
M4x20
Wall fixing part
Body Holder
(L)
Figure 2
After finished Hanging, mounted on
the wall in Picture-6 tighten the screws.
you can see the delicate balance settings
to Picture-7
5
5x50
M5x10
Horizontal Positioning
Picture 7
Resim 10
Picture 8
Picture 9
EN
After you have installed instead of the hood.Fixing hood body
center hole (C) with a screw to wall.
Picture-8
Aluminum pipe fitting
Insert the aluminium pipe on the plastic adapter. The other end
of the tube into the hole in the wall chimney insert it. Picture-9
Aluminum pipe elbows and bends should be less.
True
Picture 10
Chimneys place it on the hood body. Figure-3
Internal chimney, chimney top outer edge of
the wall mounting plate which is fixed to the
screw. Figure-4
False
Picture-10
Figure 3
Figure 4
6
PowerLed Spot Changing
Replacement of lamps
Disconnect the hood from the electricity.
Carefully remove the faulty bulb.Replace with new of the same value.
(Lamps while hot can burn your hand. Allow to cool.)
Replacing halogen lamp
Remove the metal filters.Push the lamp from the rear side
as shown in the picture (A) . And take off by turning the lamp(B).
Figure 5
Figure-5
Light Bulp
Take over the bulp by turning it counterclockwise. Replace with new of
the same value bulp by turning it clockwise.
EN
Remove aluminium filter.
Figure-6
Figure 6
Change of LED Lamps
Disconnect the electrical connection of the hood.
Remove the faulty led lamp by pulling as shown in Figure 6.1-2
Get it separated from the cable connector and insert the equivalent
led lamps provided from the service and make the electrical connection
by plugging into the socket. Tighten the spring on the edge of the lamp.
Note: Lamps are available from Authorized Services.
Warning:
To avoid the possibility of an electric shock, please make sure that the device circuit is open
before replacing the lamp.
Figure 6.1-2
Device Functions
Hoods use chimney or without chimney in the kitchen.
Figure 5
In use with chimney;
Hoods must be connected to a chimney to expel air.
chimney hoods to get the best performance from the shortest path to the pipe system
to track the note. The device stands out as being suitable for use from the factory with
a chimney.
Warning!!!
Hoods output; where the smoke duct must not be connected to the other.
Aktive Carbon filter
For environments without a chimney from the indoor air by
filtration activated carbon filter to be used indoors again. Aktive
Carbon filters should be obtained from your dealer, or service.
Picture-11
Picture 11
Whether or not use carbon filters in each case used oil filters must be installed in the product.
Do not use your product unfiltered oil. Disconnect the hood from the electricity and replace with
new carbon filter. Carbon filters should be replaced with 3-5 month intervals.
Carbon filters should not be washed in no time.
7
Figure 7a
Figure 7
EN
Circular Carbon Filter Changing
Products used in the two carbon filters
To replace the carbon filter, motor cover with carbon
filter on the channel on the channels align and turn it
clockwise. Remove to carbon filter by turning it
counterclockwise.
Figure-7
Square Carbon Filter Changing
To remove the carbon filter pressing of the upper latch
and pull it toward you.
Figure-7a
Figure 8
Washable Aluminium
cassette filters
Picture 12
Maintenance
Disconnect the hood from the electricity to maintenance or
*
cleaning.
Aluminium cassette filters the amount of airborne dust
*
and oils.
*Metal filter must be washed in hot soapy water every month or
if possible in the dishwasher (60°C)
Press on the spring clamps at the tip of cassette filter
*
and disassemble.
Do not assemble before drying after
cleaning. Figure-8 and Picture-12
Outer surfaces of your extractor must be wiped by a cloth
*
wet with liquid detergent.
Electronic components must not come into contact with
*
water or other substances.
Inox products use the appropriate cleaning and
*
maintenance materials. This will extend the life of the
device.
Warning:
Aluminium filters are dishwasher safe.
Aluminum filter
discolour after a few washes. This is a normal condition.
Does not require modification of the filters.
Efficient Ventilation
For correct ventilation , windows opening outside must be kept closed.Doors and
windows opening to other rooms may be kept openAfter the cooking process .
equipment in working order leave for a while, so the rest will be absorbed odors and
vapors.
IMPORTANT NOTE:
Pay attention when operating extractor simultaneously with devices running by
using the ambient air with fuel (such as heaters operating gas, diesel fuels, coal or
firewood, geyser etc.) because it may affect burning since extractor discharges the
air to outside.
This advice does not apply to operations without chimney.
8
Using the Hoods
The Control Panel
The control panel is in the front of the device.
Here the device is comfortable to use and can
be done easily.
EN
On/Off
Device selection stage
The speed of the device can be changed by the process. Evaporation in a process of intense speed should
be increasedat least that should be reduced in the process. The important thing about this device is operated
in conjunction with a stove. The resulting balanced airflow will positively affect traction device. After finishing
device is recommended to run a few more minutes.The automatic shutdown system can be used for this
operation.
Minus
Display
Plus
Timer
Lighting
On/Off
Use of Electronic Keys
a) Motor On/Off:
It can be used for opening and closing the engine. At the begining engine start with second speed.
b) Speed Selection:
V - (Negative) : It can be used to lower speed of engine to the first speed. When the button is pushed as
continual speed of engine is become less. And when the button is pushed one time speed of engine
decreases one time.
V + (Positive) : It can be used to increase speed of engine to the highest period. When the button is
pushed as continual speed of engine is become to rise continiously. And when the button is pushed one
by one speed of engine increasees one by one.
c) Automatic Shutdown (Timer):
If the timer button is pushed while the engine is running, speed button will start to flash than 15 minutes
later engine and lamp will be closed. If the timer buttn is pushed again the flash stops and timer will be
canceled.
d) Lighting On/Off:
It can be used for opening and closing the lamp.
e) Filter Alerts:
After working on the device display a specific expression that metal filters must be cleaned (C) warning
appears.After the filter has been cleaned and replaced the engine on / off button for 5 seconds. hold.
Before (C) and then (E) notice appears. At the end of this process, the filter will be reset warning.
9
Loading...