KL Outdoor Sun Dolphin Series, Water Wheeler 5, Water Wheeler ASL, ASL Owner's Manual

OWNER’S MANUAL

Pedal Boat Models:

Sun Dolphin-all models

Water Wheeler 5 & ASL

1790 Sun Dolphin Drive
Muskegon, Michigan 49444
phone [phone]
fax [phone]
email [e-mail]
website www.sundolphin.com

Congratulations on the recent purchase of your new pedal boat! You have purchased a boat from one of the nations leading
manufacturers of small boats. Your boat represents years of commitment to product design, excellence in engineering and quality in
manufacturing. With proper care and maintenance your pedal boat should last for many years to come. Please call our helpful and
knowledgeable Customer Support Department if you have any questions.

MATERIALS

Your pedal boat is manufactured from High Density Polyethylene (HDPE). It is a very durable material. Our
specially formulated HDPE has an ultra-violet inhibitor blended throughout the material to reduce color fade
and maintain its strength. Polyethylene is a somewhat flexible material with some memory. This means it has
a tendency to return to its original molded shape if distorted. All boats are equipped with closed cell foam for
flotation.

BOAT SET-UP

Rudder

It is necessary for you to change the rudder from its shipping position to the operating position. See Photos
#1 and #2. Remove the rudder and pin it through the top hole of the rudder so it hangs with the straight side
towards the front of the boat. Be sure to secure it with cotter ring.

Adjustable Seats

Two adjustable seats come with Sun Dolphin Sun Slider and Water Wheeler ASL Pedal Boats. Adjust the seat
to accommodate your height by placing it in the notched positions. For lounging, simply place seat in the back
footwell notches.

Paperwork

Warranty Registration Card

To properly register your boat with KL Outdoor for warranty validation please fill out the warranty registration form
online at www.sundolphin.com. Please review our full warranty statement. The serial number can be found on the
outside of the hull in the back right corner just under the rubrail. See Photo #3.

Photo #1 Shipping

Position

Photo #2 Operating

Position

Photo #3 Serial Number

Location

Manufacturers Statement of Origin (MSO)

You should receive a MSO with your new boat. Some states may require a MSO for proper registration of your boat. If you plan on
putting an electric motor on then it may be necessary to register it. Please check with your local dealer or state licensing bureau.

Owner’s Manual

Keep your owner’s manual for future reference. It is a good idea to write down the following information:
Serial Number ________________________________
Date of Purchase ________________________________
Purchased from ________________________________

Applying Decals

Before applying boat registration decals (if required), clean the area with alcohol or any solvent that does not leave a residue. Make
sure solvent is put aside and is dry. Using a propane torch, lightly pass the flame back and forth over the area where the decals will
be applied. Don’t try to heat the surface. This process will enhance the adhesion of the decals.

TRANSPORTING YOUR PEDAL BOAT

Your pedal boat has a covered compartment in the rear. Always face the stern (rear) of the boat towards the direction of travel to
prevent the wind from tearing the compartment lid off. If this happens you can contact KL Industries for replacement.

Do not transport with the adjustable seat backs in place. They may bounce out.

CARE AND MAINTENANCE

With minimal care and maintenance, your boat has been designed to provide you with many years of enjoyment.

• Drain any water accumulated between deck and hull. See Photo #4.

• Your pedal boat can be cleaned with warm water and any standard detergents. More difficult stains, such as brackish watermarks
may be cleaned with a petroleum based cleaner. Read the manufacturers’ instructions carefully before using any cleaner.

• If your boat is used in salt-water environments it is suggested that the boat and components be rinsed thoroughly with fresh water
after each use. See optional accessories for salt-water upgrade.

• Your pedal boat comes standard with our exclusive oil impregnated bronze bushings. They are commercial quality and don’t need
frequent lubricating. After the first few uses you may see a black watermark down the inside of your boat. This is simply the paint
on the crank inside the bushing wearing off. This is normal and can be cleaned as above.

• Use some care when beaching the boat. Avoid dragging it across asphalt, concrete or sharp rocks to
prevent excessive wear and abrasion to the hull bottom.

• Polyethylene is a somewhat flexible material with some memory. This means it has a tendency to return
to its’ original molded shape if distorted. If this occurs follow these steps:

1. Relieve the pressure that caused the dent or distortion by supporting the boat differently or removing gear.

2. Place the boat in the warm sun. Usually the south side of a building is the warmest spot. As the boat warms

up usually (but not always) the boat will return to its original molded shape. This may take a few hours or a
couple of weeks depending upon outside temperatures and the degree of distortion.

STORAGE

• If possible, it is best to store your pedal boat inside for the winter. If stored outside custom mooring covers that prevent water and
debris from accumulating are available from KL Outdoor. Order online at www.sundolphin.com.

• When storing your boat, open the drain plug and stand it on its front bow to ensure proper drainage. Either store it on its bow or
turn it upside down.

• Don’t allow water to accumulate between the deck and hull and freeze. Freezing damages the polystyrene flotation foam.

• Don’t place the boat on 4x4’s or sawhorses. Dents will form in the hull.

OPTIONAL ACCESSORIES

Order online at www.sundolphin.com.

Photo #4 Drain Plug

Location