KlipXtreme BluBeats KHS-630 User Manual
stereoheadset
BluBeats
Stereo headset with
Bluetooth® Wireless Technology
KHS-630
2 3
II. Product components
English
I. Introduction
Main features
Enjoy hands-free conversations and a clear signal reception up to 10 meters
away from your computer or audio source.
Compatible with other Bluetooth enabled devices, such as tablets,
computers, smart phones, iPads, iPhones and iPods.
Ideal for phone calls, PC interactive gaming, internet voice chats and
conferencing.
Wide adjustable headband and leatherette ear pads provide comfortable
listening for hours on end.
Up to 10 hours of normal operation and approximately 300 hours of
stand-by time.
Built-in 360° microphone, for clear voice chats.
Micro-SD card slot for music playback.
Li-polymer rechargeable battery.
Headset with Bluetooth Wireless Technology
Standard to mini USB charging cable
3.5mm to 3.5mm stereo connector
User’s guide
•
•
•
•
•
•
•
•
•
•
•
•
Package contents:
Thank you for purchasing the Klip Xtreme KHS-630 Stereo Headset with Bluetooth
Wireless Technology. We encourage you to read this quick installation guide thoroughly
to get the most of this innovative wireless headset.
2
1
4
8
3
7
5
10
6
1
9
4 5
Foldable and adjustable headband
Power switch: slide up to turn it on/down to turn it o.
Multifunction button (MBF):
>>/V+: press this button once to select the next track. Press and hold to
increase the volume of the unit.
<</V-: press this button once to select the previous track. Press and hold
to lower the volume of the unit.
Charging socket: insert the mini-USB plug here.
3.5mm jack: for wired playback.
Built-in microphone: picks up your voice.
Micro-SD card slot: insert the micro-SD card here.
LED status indicators:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
•
•
•
•
•
•
•
•
Press it to start and pause music playback. When using the phone feature,
press this button to answer, ignore or end a call.
Press and hold this button to switch modes. The available modes are:
3.5mm, SD card and Bluetooth.
Solid red: indicates the headset is charging when the device is o.
Alternating green and blue LED: indicates headset has entered into the
pairing mode and is ready to be detected for the rst time.
Blinking blue and green simultaneously: indicates the battery is running
out of power.
Blinking green slowly: indicates the headset has connected to the
Bluetooth device.
Blinking blue slowly: indicates that the micro-SD card has been detected.
Solid blue: indicates that the 3.5mm connection has been detected.
III- Basic operation
Charge your headset
Turning your headset on and o
Plug the supplied USB cable into the USB port of your computer or to a 5V
USB adapter to charge the battery. The headset must be turned o while
charging.
Make sure that your KHS-630 headset is fully charged before using it for the
rst time.
The headset battery has to be initially charged for at least for 4 hours.
Thereafter, the battery will take from 2 to 3 hours to recharge.
While charging, the LED will be solid red. When the battery has reached full
capacity, the red LED will turn o.
•
•
•
•
Slide the power switch up to turn the headset on.
Slide the power switch down to turn o the device.
Note: during power on, if the 3.5mm connection is detected, then it becomes the
primary mode for the headset.
1.
2.
6 7
IV-Advanced operation
Note:
Pairing the headset with your computer
Before installing this product, please make sure your device has a built-in
Bluetooth feature available. You can pair up to eight devices to your KHS-630
headset.
Make sure the headset is o.
Activate the Bluetooth program in your PC to begin setup.
The “Search new device” screen will be displayed.
Place both devices not more one meter away from each other.
Slide the power switch up to turn the headset on. The green and blue LED will
alternate quickly indicating that the device has entered into pairing mode.
Select KHS-630 as soon as the system detects the headset. Double click on the
icon representing the headsets.
The software may activate the passkey window and ask you to enter the PIN
code =“0000” (4 zeros). Otherwise, the wireless connection will be established
automatically with the remote device.
If the pairing is successful, the green status LED will start blinking slowly. If after
60 seconds the pairing process fails, please repeat steps 1 through 7 described
above.
The headset will go automatically into standby mode after a short period of
inactivity.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Pairing the headset with your portable device
Make sure the headset is o.
Set your Bluetooth device to “discover” the wireless headset.
Place both devices not more than one meter away from each other.
Slide the power switch up to turn the headset on. The green and blue LED will
alternate quickly indicating that the device has entered into pairing mode.
Select KHS-630 as soon as your portable device detects the headset.
Accept by pressing Yes or OK on the device. If prompted, enter the passkey =
0000 (4 zeros). Your device will conrm when pairing is complete.
If the pairing is successful, the green status LED will start blinking slowly. If after
60 seconds the pairing process fails, please repeat steps 1 through 6 described
above.
The headset will go automatically into standby mode after a short period of
inactivity.
1.
2.
3.
4.
5.
6.
7.
8.
Using the Bluetooth wireless headset
1. Answering and ending a call using your mobile phone
When there is an incoming call, your phone will ring.
Briey press the MFB button to pick up. You may also press the answer button
on your cellular phone to receive the call in your headset.
To end a call, simply press the MBF once again. Likewise, you may also nish the
call directly using the controls on your cell phone.
•
•
•
8 9
Specications
• RF frequency range 2.402~2.480GHz
• Modulation type GFSK (Gaussian Frequency Shift Keying)
• Connectivity standard Bluetooth V2.1 with Enhanced Data Rate
• Maximum range Up to 10 meters (33 ft) in open spaces
• DC input: 3.2-4.2V
• Additional audio inputs Micro-SD card slot (8GB max) and 3.5mm
stereo jack
• Operating current: 45mA
• Status indicator Red, green and blue LEDs
DRIVER UNIT
• Housing size Ø40mm
• Impedance 32Ω
• Sensitivity 82dB
• Frequency response 20Hz - 20kHz
MICROPHONE
• Directivity Omnidirectional
• Impedance 2.2k Ohm
• SPL -42dB
• Frequency response 50Hz-20kHz
2. Music playback
On Bluetooth mode
With the micro-SD card
>>/V+: press and hold to adjust volume up.
<</V- : press and hold to adjust volume down.
>>/V+: press once to select the next track.
<</V-: press once to select the previous track.
When listening to music using your mobile phone, and there is an incoming call,
playback will resume automatically once the call has ended.
Insert a micro-SD card into the corresponding slot (8)
Press the MFB to switch input mode.
>>/V+: press and hold to adjust volume up.
<</V- : press and hold to adjust volume down.
>>/V+: press once to select the next track.
<</V-: press once to select the previous track.
•
•
•
•
•
•
•
•
•
•
•
10 11
Precautions
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Do NOT drop, hit or shake the device.
Do NOT disassemble, repair or modify the headset yourself.
Do NOT use cleaning products that contain benzene, solvents or alcohol.
Do NOT expose headset to excessive heat or to direct sunlight for long periods
of time.
Do NOT store the device in a place with high humidity or dust.
Do NOT place heavy objects on top of the headset.
Do NOT use near a microwave oven or wireless LAN products.
•
•
•
•
•
•
•
POWER
• Battery type 320mAh built-in lithium-polymer
• Charging connector type Mini-USB plug
• Run time Up to 10 hours of talk or music playback time
• Standby time Up to 300 hours
• Charging time 2.5 hours
Loading...