Product Specifications
®
Confidential to Cotron from Sunitec under NDA
User manual
Model:Klipsch Reference Over-Ear Bluetooth
Brand:klipsch
Content
REVISION HISTORY--------------------------------------------------------------------------------------- 2
Preface---------------------------------------------------------------------------------------------------------- 4
Product Specifications----------------------------------------------------------------------------------------4
Product appearance------------------------------------------------------------------------------------------- 4
Operation------------------------------------------------------------------------------------------------------- 5
Low battery indication and charging-----------------------------------------------------------------------7
Summary of LED Indication-------------------------------------------------------------------------------- 7
Product Specifications
®
Preface
Product Specifications
Bluetooth Compatible Specifications: V4.0
Operating Frequency Band: 2.4GHz~2.48GHz unlicensed ISM Band
Output Power: Class 2 Power Output, up to 10 meters
Support Profiles: A2DP1.2 AVRCP 1.4 HFP1.5 HSP1.2
Support SBC APTX AACcodec
Battery Used: TBD 3.7V DC
PCB Size: 78.0mm*53mm*0.8mm
Weight: TBD
Size:TBD
Product appearance
Operating Frequency Band: 2.402GHz~2.480GHz unlicensed ISM Band
The purpose of this product specification is to provide technical information for the Bluetooth Stereo BT
Headset Klipsch On-Ear BT, Product Design, manufactured and supplied by Sunitec Enterprise Co., LTD.
Product Specifications
®
Operation
Confidential to Cotron from Sunitec under NDA
Turning ON/OFF
To turn on the BT HEADSET
When BT HEADSET is under off mode, press and hold the “Power” button 5 seconds until you hear
tone and blue LED fade in.
To turn off the BT HEADSET
Press and hold the “Power” button 3 seconds until you hear
When losing the connection. the BT HEADSET will be automatically turn off in 2 minutes later.
Pairing
You are required to pair the BT HEADSET with you mobile phone before using it.
1)under power off mode. press and hold the “Power” button 5 seconds power on BT HEADSET, BT
HEADSET will enter pair mode after power on if reconnect fail;
2).The phone will search all Bluetooth devices within 10 meters and display them as a list
3).Select “Klipsch On-Ear BT” from the list. Enter the passkey “0000”（if need）to pair and connect the
BT HEADSET to you phone.
4).You will hear tone of paired indication when both devices are successfully paired.
Note: If the pairing can’t be completed within 2 minutes after the pairing mode is activated, the BT
HEADSET will be enter ower off mode.
a tone and red Blue LED fade out.
a
Product Specifications
®
Confidential to Cotron from Sunitec under NDA
Connection
In some cases the device could be disconnected from your phone. For example, if the BT HEADSET was
switched off. To restore the connection between the BT HEADSET and your phone:
1).If the BT HEADSET has been turn off: turn on the power and the connection will be restored
automatically.
2).If the mobile phone has been switch off: turn on the mobile phone and restore the connection via the
phone menu or press the “Power” button once.
3).If one of the two devices has been out of range，the device will connect automatically within 3 minutes;
If timeout, press the “Power” button once to connect.
Disconnection
Sometimes you need to disconnect your phone from the BT HEADSET. For example, if the phone should
communicate with another Bluetooth device. To disconnect the BT HEADSET and your phone:
1).Turn off the BT HEADSET.
2).Disconnect the BT HEADSET in the phone menu.
Answer Calls
When incoming call, press the “MFB” button once to answer the call.
Ending Calls
During the call, press the “MFB” button end the call.
Rejecting Calls
When incoming call, press and hold the “MFB” button for 1 second to reject an incoming call.
Answer or reject the second call：
-Answer the second call: during a call, when another call coming, Short press the “MFB” to pick up the
call and the first call will be end.
-Reject the second call: during a call, when another call coming, press and hold “MFB” for 1 second to
reject the call.
Voice dial
-During connection, Long press 1 second the “MFB” start voice dial.
Play/Pause
If BT HEADSET is connected the phone or other audio device, short press the “MFB” button to
starting the music playing, then short press the “MFB” button again pause the music.
Forward
Under music mode, short press the “Vol+” button for 1 second to forward song.
Backward
Under music mode, short press the “Vol-” button for 1 second to Backward song.
Adjusting the Volume
Product Specifications
®
Low battery indication and charging
Summary of LED Indication
Confidential to Cotron from Sunitec under NDA
To increase the volume –During the call or Music, Short press “Vol+” button to increase volume by one
level.
To decrease the volume –During the call or Music, Short press “Vol-” button to decrease the volume
by one level.
Toggle mute
Short press “Vol+” and “Vol-” at the same time to mute the mic when call is active.
Reset Paired List
Under off mode, VVlong press and hold “Power” and “Vol-” button for 10 second to clear paired device.
Enter DUT mode
Under pairing mode, long press and hold “Power” and “Vol+” button for 3 second to enter DUT mode.
Enter Service mode
Under pairing mode, Vlong press and hold “Vol+” and “Vol-” button for 3 second to enter DUT mode.
BT HEADSET charging voltage via USB to 5V.When the battery voltage is lower than 3.4V, the
red LED begins to flash And A tone sounds every 1 minutes. When the battery voltage is lower than
3.1V BT HEADSET will automatically shut down.
Status LED Indication
Power on Blue Fade In
Power off Blue Fade Out
Standby mode(connected) Blue single flash 2 sec between flashes
Idle mode(disconnected) Red double flash 0.2s on, 0.2s off, 0.2s on, 5 sec off
Pairing in progress Pulsing blue 1s fade in, 1s fade out, 2 sec dark
Play Music Blue triple flash 2 sec between flash sets
low battery Red single burst 0.5s on, 60s off
Charging in progress Solid red
Charging completed Red LED off
Incoming/Outgoing call blue flashing
Active call 2 sec between flash sets
Reset Paired device list Red/Blue Flash x5
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
IC Caution.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modications to your device not expressly
approved by the party responsible for compliance can void the user’s authority to
operate the equipment.
Cet appareil est conforme aux règlements FCC partie 15 et RSS-210 de la IC.
Le fonctionnement est sujet aux deux conditions suivantes:
(1) Cet appareil ne peut causer d’interférences nuisibles
(2) Cet appareil reçoit toute interférence même celles pouvant occasionner un mauvais
fonctionnement. Les modications apportées à votre appareil et non expressément
approuvées par la partie responsable de la conformité peuvent annuler le droit de
l'utilisateur à utiliser l'équipement
Loading...