KLING & FREITAG CA 1215, CA 1515 User Manual

Download

Page 1

KLING & FREITAG CA 1201, CA 1215, CA 1515

User's Manual

Important Information, Please Read Before Use!

KLING & FREITAG GmbH

Junkersstrasse 14

D-30179 Hannover

PHONE 0 (049) 511- 969 97-0

FAX 0 (049) 511- 67 37 94

www.kling-freitag.de

Version 4.2 Stand: 07.05.2015

Page 2

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

Contents

Inhaltsverzeichnis

1.1.

1. Introduction 3

2.2.

2. Symbols in User's Manual 4

3.3.

3. Information about this User's Manual 4

4.4.

4. General Instructions for Using Speakers 5

5.5.

5. Product Descriptions and Versions 7

5.1 CA 1201 7

5.2 CA 1215-6 8

5.3 CA 1215-9 9

5.4 CA 1515-6 10

5.5 CA 1515-9 11

6.6.

6. Important Notes for the Options ‘Outdoor’ and ‘Installation’ 12

6.1 ‘Installation’ 12

6.2 ‘Outdoor Mobile’ 12

6.3 ‘Outdoor Installation’ 12

7.7.

7. Notes for Versions with ‘100V’ Option 13

7.1 Reasons for choosing Speakers with 100 V Transformers 13

7.2 Connecting Diagram of the 100V Speaker Inputs 13

8.8.

8. Instructions for Suspending the Speakers 14

8.1 Rigging without K&F Adjustable Speaker Mount or Ceiling Bracket 14

8.2 Using the ‘allsafe JUNGFALK’ Flying Points 15

9.9.

9. Coverage Patterns of the CA Speakers 16

9.1 Changing the Coverage Pattern 16

10.

10.10.

10. Mounting Instructions for Speakers 17

10.1 Proper Arrangement of the Loudspeakers 17

10.2 Arrayed Speaker Systems (Cluster) 18

10.2.1 Horn not rotated 18

10.2.2 With rotated Horn 19

11.

11.11.

11. Wiring 20

11.1 Connecting the Speakon Connector to the Terminal 20

11.2 Avoiding Ground Loops 21

11.2.1 What is a Ground Loop? 21

11.2.2 Avoiding Ground Loops 21

12.

12.12.

12. Configurations and Connecting Diagrams 22

12.1 Operating the Systems without K&F System Controller 22

12.1.1 CA Systems in Full-Range Mode 22

12.1.2 Full Range Mode & Subwoofer with Crossover (XO) 23

12.2 Operations with K&F System Controller 24

13.

13.13.

13. Operating the Speakers 24

14.

14.14.

14. Crossovers 25

Page 3

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.1 Wiring Diagram CA 1201 25

14.1.1 Version A 25

14.1.2 Version B 26

14.2 Wiring Diagram CA 1215-6 and CA 1215 -9 27

14.2.1 Version A 27

14.2.2 Version B 28

14.3 Wiring Diagram CA 1515-6 and CA 1515-9 29

14.3.1 Version A 29

14.3.2 Version B 30

15.

15.15.

15. Touching Up Damage to Paint / Changing the Front Foam 30

16.

16.16.

16. Technical Specifications 31

16.1 CA 1201 31

16.2 CA 1215-6 32

16.3 CA 1215-9 33

16.4 CA 1515-6 34

16.5 CA 1515-9 35

17.

17.17.

17. Measuring Charts 36

17.1 CA 1201 36

17.2 CA 1215-6 38

17.3 CA 1215-9 40

17.4 CA 1515-6 42

17.5 CA 1515-9 44

18.

18.18.

18. Dimensions 46

18.1 CA 1201, CA 1215-6 and CA 1215-9 46

18.2 CA 1201-M, CA 1215-6-M and CA 1215-9-M 47

18.3 CA 1201, CA 1215-6 and CA 1215-9 with Option ‘Installation’ 48

18.4 CA 1515-6 and CA 1515-9 49

18.5 CA 1515-6 and CA 1515-9 with Option ‘Installation’ 50

18.6 Accessories for the CA Systems 51

19.

19.19.

19. Disposal 53

19.1 Germany 53

19.2 EU, Norway, Iceland, and Liechtenstein 53

19.3 All other Countries 53

1.1.

1. Introduction

Thank you for your decision to buy a Kling & Freitag product. To guarantee a trouble-free operating of the equipment and to enable the KLING & FREITAG CA speaker system to achieve its full potential, please read the operating instructions carefully before use.

Page 4

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

With the purchase of a CA system, you have acquired a speaker system with the highest possible quality and performance capabilities.

As the owner of this system, you now have a versatile and highly professional tool which, when operated properly, is a true pleasure to use.

2.2.

2. Symbols in User's Manual

Warning

This symbol indicates the possibility of life-threatening danger and a health risk for persons. Not following these instructions may result in serious health problems including potentially fatal injuries.

Caution

This symbol indicates a possibly dangerous situation. Not following these instructions may cause minor injuries or cause property damage.

Important

This symbol gives instructions for the proper use of the described pro-ducts. Not following these instructions may cause malfunctions or property damage.

3.3.

3. Information about this User's Manual

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9 Version 4.2, 07.05.2015

All specifications in this manual are based on information available at the time of publishing for the features and safety guidelines of the described products.

Technical specifications, measurements, weights and properties are not guaranteed.

The manufacturer reserves the right to make product alterations within legal provisions as well as changes to improve product quality.

All persons who use the speaker system must have this guide and all further information for safe oper

All persons who use the speaker system must have this guide and all further information for safe operAll persons who use the speaker system must have this guide and all further information for safe oper

All persons who use the speaker system must have this guide and all further information for safe opera-

a-a-

tions

tionstions

tions available to them during assembly, disa

available to them during assembly, disaavailable to them during assembly, disa

available to them during assembly, disasssssembly, and use.

sembly, and use.sembly, and use.

sembly, and use.

We appreciate any input with suggestions and improvements for this manual. Please send this to us at the following address:

info@kling-freitag.de

or to:

KLING & FREITAG GMBH Junkersstr.14 D-30179 Hannover

Phone +49 (0) 511 - 96 99 70 Fax +49 (0) 511 - 67 37 94

Page 5

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

4.4.

4. General Instructions for Using Speakers

Mounting the speakers

Mounting the speakersMounting the speakers

Mounting the speakers

To prevent injury, the speakers must be securely placed on the floor or secured to the wall according to the instructions on page 17 (Mounting Instructions for Speakers). Please note that speakers can move as a result of vibrations. To prevent them from falling from their mounted position, they must be secured properly. If the weight of the speaker exceeds 20 kg then it is necessary for two people to carry it.

Speakers may only be suspended or mounted to walls or ceilings by qualified personnel. The speakers must be hung by using at least two of the designated flying points. The same applies when lifting and aligning the speakers.

Never use signal cables or power cords for suspending, aligning or securing the systems. When laying the connecting cables, make sure that nobody can trip.

Never hang more than two speakers under one another without using the designated Kling & Freitag rigging equipment.

Ensure that all installation connections comply with the applicable safety guidelines and that the size and strength are sufficient. Further instructions are in our user's manual for assembly equipment and in the general safety instructions for speakers and assembly equipment.

For mobile and fixed installations, use only rigging equipment from KLING & FREITAG. Make sure to observe the included safety and mounting instructions for loudspeakers and accessories.

Speakers and rigging equipment must be visually examined at regular intervals. If there are signs of wear, they must be replaced immediately. Furthermore, screwed connections of supporting parts must be checked routinely.

Protecting the speakers / avoiding fire hazard

Protecting the speakers / avoiding fire hazardProtecting the speakers / avoiding fire hazard

Protecting the speakers / avoiding fire hazard

In general, audio signals should not be overdriven. This may be caused by mixing consoles, equalizers, effect equipment, etc. and should be indicated on this equipment. When a power amplifier is overloaded at the output (clipping), then the amplifier should activate a clipping warning signal. Power amplifiers can also be overloaded at the input circuit without the amplifier signalling the clipping, i.e. when there is not sufficient headroom in the input circuit. We, therefore, recommend turning up the power amplifiers all the way and adjusting the level before the power amplifier in order to avoid overloading the input circuit. In any case, the signal must be reduced as soon as it sounds unnaturally distorted.

To protect the speakers from being destroyed and to avoid fire hazard, they should only be operated with professional power amplifiers with the following specifications:

Integrated or preceding subsonic filter (approx. 30 Hz, min. 12 dB / octave)

integrated clipping limiter

for speaker models CA 1201 or CA 1215: maxim

um r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

axim

um r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

xim

um r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

um r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

um r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

m r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

r at ed po wer 500

W@8•

•(equi val ent 1000W@4•)

r at ed power 500

W@8•

•(equi val ent 1000W@4•)

at ed power 500

W@8•

•(equi val ent 1000W@4•)

t ed power 500

W@8•

•(equi val ent 1000W@4•)

ed po wer 500

W@8•

•(equi val ent 1000W@4•)

d power 500

W@8•

•(equi val ent 1000W@4•)

power 500

W@8•

•(equi val ent 1000W@4•)

power 500

W@8•

•(equi val ent 1000W@4•)

ower 500

W@8•

•(equi val ent 1000W@4•)

wer 500

W@8•

•(equi val ent 1000W@4•)

er 500

W@8•

•(equi val ent 1000W@4•)

r 500

W@8•

•(equi val ent 1000W@4•)

500

W@8•

•(equi val ent 1000W@4•)

500

W@8•

•(equi val ent 1000W@4•)

W@8•

•(equi val ent 1000W@4•)

W@8•

•(equi val ent 1000W@4•)

W@8•

•(equi val ent 1000W@4•)

@8•

•(equi val ent 1000W@4•)

8•

•(equi val ent 1000W@4•)

•

•(equi val ent 1000W@4•)

•

•(equi val ent 1000W@4•)

•

(equi val ent 1000W@4•)

(

equi val ent 1000W@4•)

qui val ent 1000W@4•)

ui val ent 1000W@4•)

i val ent 1000W@4•)

val ent 10 00W@4•)

al ent 1000W@4•)

l ent 10 00W@4•)

ent 1000W@4•)

nt 1000W@4•)

t 1000W@4•)

1000W@4•)

000W@4•)

00W@4•)

0W@4•)

W@4•)W@4•)@4•)4•)•)

)

for speaker model CA 1515: maxim

um rated power 700W@8

• (equivalent 1400W@4•)

axim

um rated power 700W@8

• (equivalent 1400W@4•)

xim

um rated power 700W@8

• (equivalent 1400W@4•)

um rated power 700W@8

• (equivalent 1400W@4•)

um rated power 700W@8

• (equivalent 1400W@4•)

m r ated power 700W@8

• (equivalent 1400W@4•)

rated power 700W@8

• (equivalent 1400W@4•)

r ated power 700W@8

• (equivalent 1400W@4•)

ated power 700W@8

• (equivalent 1400W@4•)

ted power 700W@8

• (equivalent 1400W@4•)

ed power 700W@8

• (equivalent 1400W@4•)

d power 700W@8

• (equivalent 1400W@4•)

power 700W@8

• (equivalent 1400W@4•)

power 700W@8

• (equivalent 1400W@4•)

ower 700W@8

• (equivalent 1400W@4•)

wer 700W@8

• (equivalent 1400W@4•)

er 700W@8

• (equivalent 1400W@4•)

r 700W@8

• (equivalent 1400W@4•)

700W@8

• (equivalent 1400W@4•)

700W@8

• (equivalent 1400W@4•)

00W@8

• (equivalent 1400W@4•)

0W@8

• (equivalent 1400W@4•)

W@8

• (equivalent 1400W@4•)

•

(equivalent 1400W@4•)

(

equivalent 1400W@4•)

quivalent 1400W@4•)

uivalent 1400W@4•)

ivalent 1400W@4•)

valent 1400W@4•)

alent 1400W@4•)

lent 1400W@4•)

ent 1400W@4•)

nt 1400W@4•)

t 1400W@4•)

1400W@4•)

400W@4•)

00W@4•)

0W@4•)

W@4•)W@4•)@4•)4•)•)

)

If you wish to use a speaker with a power amplifier which does not fulfil these specifications, then the speaker should be controlled using a Kling & Freitag system controller with limiter function. This is the only way overloading and the risk of fire can be avoided. The results of such a power amplifier defect cannot be avoided by the controller.

Important

Warning

Page 6

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

If power amplifiers have power ratings lower than mentioned above, then it is imperative that a clipping limiter is used to protect the speaker even if it is used with a Kling & Freitag system controller.

For damage caused by overloading or use with power amplifiers other than those recommended above, Kling & Freitag GmbH does not assume warranty and excludes liability for possible consequential damage.

The following signals may damage the speakers

The following signals may damage the speakersThe following signals may damage the speakers

The following signals may damage the speakers

Permanent high-pitched signals with high frequency, and continuous noise from feedback.

Permanently distorted signals with high power.

Noises, which occur when the amplifier is on while equipment is being connected, disconnected or switched on.

Do not install speakers in any of the foll

Do not install speakers in any of the follDo not install speakers in any of the foll

Do not install speakers in any of the following places:

owing places:owing places:

owing places:

Where the speakers are permanently exposed to direct sunlight

Where the speakers are exposed to high moisture

Where the speakers are exposed to strong vibrations and dust.

Damage caused by the speakers' magnetic fields

Damage caused by the speakers' magnetic fieldsDamage caused by the speakers' magnetic fields

Damage caused by the speakers' magnetic fields

Speakers are permanently surrounded by a magnetic field even when they are not operating. Therefore, during transport and placement of the speakers, it is important to ensure that there is always approx. 1 m between the speakers and magnetic data media and computer/video monitors.

Preventing hearing damage

Preventing hearing damagePreventing hearing damage

Preventing hearing damage

To prevent the risk of hearing damage, avoid being too close to operating speakers, even if the volume level seems to be low enough. In general, volume levels over 90 dB can cause hearing damage.

Important

Cautio

CautioCautio

Cautionnnn

Page 7

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

5.5.

5. Product Descriptions and Versions

5.1 CA 1201

Short description:

Short description:Short description:

Short description:

2-way full-range speaker system with 12" low-mid chassis and 1" high frequency driver on a rotatable 90° x 60° CD horn. Homogeneous coverage and constant directivity starting at 1.2 kHz. Integrated crossover with self-resetting protection circuit for low-mid and high frequency path.

Enclosure:

Enclosure:Enclosure:

Enclosure:

Trapezoidal enclosure with additional cluster angles, 15 mm birch plywood, highly resistant structured grey or black finish, internal mounting flange, 5 ‘allsafe JUNGFALK’ flying points, 2 butterfly handles, highly permeable, ball proof steel grille with exchangeable black acoustic foam.

Optional versions:

Optional versions:Optional versions:

Optional versions:

− CA 1201-M: Enclosure with additional monitor angle

− CA 1201-100V: 100V version with 300 VA toroidal transformer

− CA 1201 --- ‘Installation’ Version for fixed installations

− CA 1201 --- ‘Outdoor Installation’ / ‘Outdoor Mobile’ Versions for outdoor use under roofs

− CA 1201-SP: Version with integrated power amplifier technology (not for CA 1201-M) 'SP' speakers are shipped with a separate user's manual!

− Special finish in RAL colours

Page 8

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

5.2 CA 1215-6

Short description:

Short description:Short description:

Short description:

2-way high-performance speaker system with 12" low-mid chassis and 1.5" high frequency horn driver on a rotatable 65° x 50° CD horn. Homogeneous coverage and constant directivity starting at 1.2 kHz. Integrated crossover with self-resetting protection circuit for high frequency path, delay time and phase optimisation.

Enclosure:

Enclosure:Enclosure:

Enclosure:

Trapezoidal enclosure with additional cluster angles, 15 mm birch plywood, highly resistable structured grey or black finish, internal mounting flange, 5 ‘allsafe JUNGFALK’ flying points, 2 butterfly handles, highly permeable, ball proof steel grille with exchangeable black acoustic foam.

Optional versions:

Optional versions:Optional versions:

Optional versions:

− CA 1215-6-M: Enclosure with additional monitor angle

− CA 1215-6 100V: 100V version with 300 VA toroidal transformer

− CA 1215-6 - ‘Installation’ Version for fixed installations

− CA 1215-6 - ‘Outdoor Installation’ / ‘Outdoor Mobile’ Versions for outdoor use under roofs

− CA 1215-6-SP: Version with integrated power amplifier technology (not for CA 1215-6-M) 'SP' speakers are shipped with a separate user's manual!

− Special finish in RAL colours

Page 9

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

5.3 CA 1215-9

Short description:

Short description:Short description:

Short description:

2-way high-performance speaker system with 12" low-mid chassis and 1.5" high frequency driver on a rotatable 90° x 50° CD horn. Homogeneous coverage and constant directivity starting at 1.0 kHz. Integrated crossover with self-resetting protection circuit for high frequency path, delay time and phase optimisation.

Enclosure:

Enclosure:Enclosure:

Enclosure:

Optional versions:

Optional versions:Optional versions:

Optional versions:

− CA 1215-9-M: Enclosure with additional monitor angle

− CA 1215-9-100V: 100V version with 300 VA toroidal transformer

− CA 1215-9 - ‘Installation’ Version for fixed installations

− CA 1215-9 - ‘Outdoor Installation’ / ‘Outdoor Mobile’ Version for outdoor use under roofs

− CA 1215-9-SP: Version with integrated power amplifier technology (not for CA 1215-9-M) 'SP' speakers are shipped with a separate user's manual!

− Special finish in RAL colours

Page 10

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

5.4 CA 1515-6

Short description:

Short description:Short description:

Short description:

2-way high-performance speaker system with 15" low-mid chassis and 1.5" high frequency driver on a rotatable 65° x 50° CD horn. Homogeneous coverage and constant directivity starting at 1.2 kHz. Integrated crossover with self-resetting protection circuit for chassis and crossover, delay time and phase optimisation.

Enclosure:

Enclosure:Enclosure:

Enclosure:

Trapezoidal enclosure with additional monitor and cluster angles, 15 mm birch plywood, highly resistant structured grey or black finish, internal mounting flange, 5 ‘allsafe JUNGFALK’ flying points, 2 butterfly handles, highly permeable, ball proof steel grille with exchangeable black acoustic foam, non-abrasive plastic feet.

Optional versions:

Optional versions: Optional versions:

Optional versions:

− CA 1515-6-100V: 100V version with 300 VA toroidal transformer

− CA 1515-6 - ‘Installation’ Version for fixed installations

− CA 1515-6 - ‘Outdoor Installation’ / ‘Outdoor Mobile’ Version for outdoor use under roofs

− CA 1515-6-SP: Version with integrated power amplifier technology (not for 1515-9-M) 'SP' speakers are shipped with a separate user's manual!

− Special finish in RAL colours

Page 11

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

5.5 CA 1515-9

Short description:

Short description:Short description:

Short description:

2-way high-performance speaker system with 15" low-mid chassis and 1.5" high frequency driver on a rotatable 90° x 50° CD horn. Homogeneous coverage and constant directivity starting at 1.0 kHz. Integrated crossover with self-resetting protection circuit for chassis and crossover, delay time and phase optimisation.

Enclosure:

Enclosure:Enclosure:

Enclosure:

Optional versions:

Optional versions: Optional versions:

Optional versions:

− CA 1515-9-100V: 100V version with 300 VA toroidal transformer

− CA 1515-6 - ‘Installation’ Version for fixed installations

− CA 1515-9 - ‘Outdoor Installation’ / ‘Outdoor Mobile’ Version for outdoor use under roofs

− CA 1515-9-SP: Version with integrated power amplifier technology (not for 1515-9-M) 'SP' speakers are shipped with a separate user's manual!

− Special finish in RAL colours

Page 12

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

6.6.

6. Important Notes for the Options ‘Outdoor’ and ‘Installation’

Speakers with the option ‘Outdoor Mobile’ and ‘Outdoor Installation’ have been opti-mised for outdoor use. They withstand temperature fluctuations in moderate climate zones and do not accumulate condensation water.

In order to guarantee the longevity and safety of the speakers, the speakers with the option ‘Outdoor’ must still be protected from direct effects of the weather.

They should be installed, for example, under a roof so that they also have sufficient protection from driving rain from the side and direct sunlight.

6.1 ‘Installation’

Version for fixed indoor installations. Features like standard version but:

− without feet and handles

− seven stainless steel flying points with internal M10 threads,

− stainless steel connecting terminal with single PG cable fitting, Ø 13 mm

Connector:

6.2 ‘Outdoor Mobile’

Version for mobile outdoor use under roofs. Features like standard version but with the following extras:

− multi-layered, temperature and UV-resistant high-tech PU marine primer,

− final coating with highly resistant structured 2K paint in RAL colours,

− waterproofed diaphragms and electronic components protected against cor-rosion with protective coat-

ing.

6.3 ‘Outdoor Installation’

Version for fixed outdoor installations under roofs. Features like 'Outdoor Mobile', but:

− without feet and handles.

− seven stainless steel flying points with internal M10 threads

− stainless steel grille

− foam covering behind grille

− visible screws made of stainless steel.

− Stainless steel connecting terminal with single PG cable fitting, Ø 13 mm (connecting scheme see version

‘Installation’)

Warning

bl = blue

bn = brown

Page 13

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

7.7.

7. Notes for Versions with ‘100V’ Option

Kling & Freitag speakers with ‘100V’ option are fitted with high-quality toroidal trans-formers. This serves to minimize loss of sound. Highly professional sound reinforcement results can be achieved using 100 V Kling & Freitag speakers.

7.1 Reasons for choosing Speakers with 100 V Transformers

− Reduction in conduction loss.

− Easy installation of a loudspeaker network due to simple parallel wiring.

The sum of the output power of the individual speakers (stated as VA = W) must not exceed the output power of the 100 V amplifier.

− Speakers are galvanically isolated.

− Speakers can be integrated into existing 100 V systems.

7.2 Connecting Diagram of the 100V Speaker Inputs

300VA transformer

all pins parallel to out

300VA

Important

ImportantImportant

Important

Page 14

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

8.8.

8. Instructions for Suspending the Speakers

The speake

The speakeThe speake

The speakers may only be suspended by trained specialised personnel.

rs may only be suspended by trained specialised personnel.rs may only be suspended by trained specialised personnel.

rs may only be suspended by trained specialised personnel.

Pay attention to the required safety factors. Please follow the accompanying safety

Pay attention to the required safety factors. Please follow the accompanying safety Pay attention to the required safety factors. Please follow the accompanying safety

Pay attention to the required safety factors. Please follow the accompanying safety and assembly instructions carefully as well as the corresponding national safety reg

and assembly instructions carefully as well as the corresponding national safety regand assembly instructions carefully as well as the corresponding national safety reg

and assembly instructions carefully as well as the corresponding national safety regu-

u-u-

lations.

lations.lations.

lations.

All sound systems used are to be secured against toppling or falling in the manner required by the carriers of the statutory accident insurances for studio or stage areas. Appropriate directions can be found in BGV C1, BGI 810-3 or corresponding local national safety guidelines.

Amongst other things, this regulation stipulates that mobile sound equipment must be secured from falling

Ensure that all connections are secured against coming loose and that only authorized, statically tested and correctly sized supports, mounting equipment, wire ropes and chains are used.

8.1 Rigging without K&F Adjustable Speaker Mount or Ceiling Bracket

An one

An oneAn one

An one----strand rigging without additional safety is

strand rigging without additional safety is strand rigging without additional safety is

strand rigging without additional safety is nnnnot permitted

ot permittedot permitted

ot permitted....

Variante 1

Variante 1Variante 1

Variante 1,

, ,

, verti

vertiverti

verticcccal

alal

al::::

At a vertical rigging without a K&F U-Mount you have to fix the loudspeaker at the upper or bottom connection points. The rear connection points are only suitable for additional tying off the speaker.

The two mounting devices (chains, wire ropes) have to be independent and parallel and must be implemented with zero drop height.

Variante 2, horizo

Variante 2, horizoVariante 2, horizo

Variante 2, horizonnnntal

taltal

tal::::

At an horizontally rigging without a K&F ceiling bracket you have to fix the loudspeaker at one flying point each side. The rear connection points are only suitable for additional tying off the speaker.

The two mounting devices (chains, wire ropes) have to be independent and parallel and must be implemented with zero drop height.

Warning

WarningWarning

Warning

WarningWarning

Warning

Page 15

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

There are several flying options, if you use a K&F U-Mount or K&F ceiling bracket. These mounts are designed specifically for each speaker systems. For further information, please contact our local dealer.

8.2 Using the ‘allsafe JUNGFALK’ Flying Points

Single Stud Fitting

Used as fastener to the ‘allsafe JUNGFALK’

flying point.

‘allsafe JUNGFALK’ flying point

Receptacle for special fasteners.

1.)

2.)

Take the single stud fitting in one hand... ... and push the locking device up against the

spring tension.

3.)

4.)

Put the flat head of the holding bolt into the

guiding of the flying point.

Release the locking device when the single stud

fitting is located in the middle of the flying point. Make sure that the locking device clicks into place.

5.)

Check that the single stud fitting is securely

fastened and cannot be pulled out.

Page 16

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

9.9.

9. Coverage Patterns of the CA Speakers

The mid-high systems can be operated in a vertical or horizontal (i.e. as a stage monitor) position. The coverage pattern of the speakers can be adapted to special needs by a 90° rotatable horn.

The table below shows the coverage angles of a standing speaker: To determine the coverage pattern of the high frequency horn, shine a flashlight through the front covering at the level of the horn. You will find a silver stripe that determines the position and coverage angles of the horn.

DEFINITION:

Standing speaker:

Horn not rotated

Horn rotated

Model

CA 1201 90° h x 60° v 60° h x 90° v

CA 1215-6 65° h x 50° v 50° h x 65° v

CA 1215-9 90° h x 50° v 50° h x 90° v

CA 1515-6 65° h x 50° v 50° h x 65° v

CA 1215-9 90° h x 50° v 50° h x 90° v

9.1 Changing the Coverage Pattern

To turn the horn, follow these steps:

To turn the horn, follow these steps:To turn the horn, follow these steps:

To turn the horn, follow these steps:

1. Remove the four grille mounting screws on the top and bottom of the speakers with a 3 mm Allen key and remove the grille from the speaker enclosure.

2. Remove the screws from the high frequency horn (also using a 3 mm Allen key). Loosen the high fre- quency horn by using both hands, palms to the outside, to grasp into the horn and lift the horn with even pressure from the palms of your hands towards the outside. Should the horn adhere to the foam rubber attached below, release it using a screwdriver or something similar to gently lever it up.

3. Rotate the horn 90° and screw the horn on tightly again (do not force it!).

4. Screw the grille on tightly.

If the coverage angle needs to be changed often, make sure that the horn is not always rotated in the same direction, as the connecting cables, when twisted, may cause the contacts of the driver to become loose.

Page 17

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

10.

10.10.

10. Mounting Instructions for Speakers

Mount the speakers securely. To avoid injury or damage, always be sure to mount the speakers securely so that they do not fall. Speakers, which are stacked, must be secured with securing straps. When laying the connecting cables, make sure that nobody can trip.

The stability of stacked systems (also valid for the use of stands and distance rods!) is contingent upon the following stability requirement. These conditions must, therefore, be guaranteed by the user:

Stacked systems may not fall over even if they are inclined by 10° in each direction. If

Stacked systems may not fall over even if they are inclined by 10° in each direction. If Stacked systems may not fall over even if they are inclined by 10° in each direction. If

Stacked systems may not fall over even if they are inclined by 10° in each direction. If this requirement is not fulfilled, then it is necessary to take steps to achieve compl

this requirement is not fulfilled, then it is necessary to take steps to achieve complthis requirement is not fulfilled, then it is necessary to take steps to achieve compl

this requirement is not fulfilled, then it is necessary to take steps to achieve compli-

i-i-

ance. Poss

ance. Possance. Poss

ance. Possiiiible measures include stra

ble measures include strable measures include stra

ble measures include strappppping it to an appropriate

ping it to an appropriate ping it to an appropriate

ping it to an appropriate base structure or fa

base structure or fabase structure or fa

base structure or fas-

s-s-

tening it using safety straps.

tening it using safety straps.tening it using safety straps.

tening it using safety straps.

10.1 Proper Arrangement of the Loudspeakers

Be aware of the fact that the logical targeted alignment of this high quality speaker system can lead to

Be aware of the fact that the logical targeted alignment of this high quality speaker system can lead to Be aware of the fact that the logical targeted alignment of this high quality speaker system can lead to

Be aware of the fact that the logical targeted alignment of this high quality speaker system can lead to

a si

a sia si

a siggggnificant qualitative increase in the acoustic result. I

nificant qualitative increase in the acoustic result. Inificant qualitative increase in the acoustic result. I

nificant qualitative increase in the acoustic result. It is not possible to make generalities about the

t is not possible to make generalities about the t is not possible to make generalities about the

t is not possible to make generalities about the

alignment of specific systems because the room has a substantial influence on the signal and the aud

alignment of specific systems because the room has a substantial influence on the signal and the audalignment of specific systems because the room has a substantial influence on the signal and the aud

alignment of specific systems because the room has a substantial influence on the signal and the audi-

i-i-

ble result.

ble result.ble result.

ble result.

As a rule, the mid

As a rule, the midAs a rule, the mid

As a rule, the mid---- and high

and highand high

and high----transducers of loudspeakers should be mounted above the aud

transducers of loudspeakers should be mounted above the audtransducers of loudspeakers should be mounted above the aud

transducers of loudspeakers should be mounted above the audiiiience'

ence'ence'

ence's face

s face s face

s face

value, so that the sound distribution cannot be sha

value, so that the sound distribution cannot be shavalue, so that the sound distribution cannot be sha

value, so that the sound distribution cannot be shaddddowed.

owed.owed.

owed.

In many cases it is advisable to mount a loudspeaker higher, so that the sound will be distributed

In many cases it is advisable to mount a loudspeaker higher, so that the sound will be distributed In many cases it is advisable to mount a loudspeaker higher, so that the sound will be distributed

In many cases it is advisable to mount a loudspeaker higher, so that the sound will be distributed

throughout the room more evenly. Low standing systems result in a greater difference in volu

throughout the room more evenly. Low standing systems result in a greater difference in voluthroughout the room more evenly. Low standing systems result in a greater difference in volu

throughout the room more evenly. Low standing systems result in a greater difference in volume b

me bme b

me be-

e-e-

tween front and back seats than higher standing systems.

tween front and back seats than higher standing systems.tween front and back seats than higher standing systems.

tween front and back seats than higher standing systems.

Please note that this is only a general guideline and the best possible result may vary from room to

Please note that this is only a general guideline and the best possible result may vary from room to Please note that this is only a general guideline and the best possible result may vary from room to

Please note that this is only a general guideline and the best possible result may vary from room to

room.

room.room.

room.

To simulate the correct alignment of the speakers beforehand, there are various programs such as ‘Ease’ or ‘Ulysses’. The Kling & Freitag speaker system data is available for download on our website www.klingfreitag.de.

The following graphics will assist in making a rough estimate as to the distance range of full-range systems. The graphics only take into consideration the sum of the direct sound and not the influence of the room. Because of this there can, in some cases, be noticeable deviation.

Distance range of SPL (direct sound level):

Distance range of SPL (direct sound level):Distance range of SPL (direct sound level):

Distance range of SPL (direct sound level):

0 dB

-6 dB

-12 dB

-18 dB

-24 dB -30 dB

2m 4m 8m 16m 32m 50m

-34 dB

Warning

WarningWarning

Warning

Page 18

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

10.2 Arrayed Speaker Systems (Cluster)

If the loud

If the loudIf the loud

If the loudspeakers are operated through the optional K&F System Controller, we reco

speakers are operated through the optional K&F System Controller, we recospeakers are operated through the optional K&F System Controller, we reco

speakers are operated through the optional K&F System Controller, we recommmmmend to turn

mend to turn mend to turn

mend to turn

on the 'Top Low Cut' filter for clustered operation. Thus the fre

on the 'Top Low Cut' filter for clustered operation. Thus the freon the 'Top Low Cut' filter for clustered operation. Thus the fre

on the 'Top Low Cut' filter for clustered operation. Thus the frequency response for this application can

quency response for this application can quency response for this application can

quency response for this application can

be optimised (see also user’s manual of the K&F System Co

be optimised (see also user’s manual of the K&F System Cobe optimised (see also user’s manual of the K&F System Co

be optimised (see also user’s manual of the K&F System Connnntrol

troltrol

troller).

ler).ler).

ler).

When operating the systems without a K&F System Controller in a clustered con-figuration, the signal level of frequencies below 300 Hz should be reduced by 3-4 dB.

10.2.1 Horn not rotated

*If several 90° systems are clustered, unwanted interference effects may appear. As a result, we do not generally recommend clustered configurations of CA 1201, CA 1215-9 and CA 1515-9 systems. If wide angles are to be covered, we recommend the use of several 60° or 65° systems in one cluster.

Horn not

rotated

Standing

speaker

Winkel 2

between middle axes

Winkel 3

A smaller angle 3 results in

a smaller vertical coverage

angle but increases the

sound power level.

Winkel 1

between the sides of the

speakers

Combination

CombinationCombination

Combination Angle 1

Angle 1Angle 1

Angle 1 Angle 2

Angle 2Angle 2

Angle 2 Angle 3

Angle 3Angle 3

Angle 3

CA 1201 with

CA 1201

45°-55°

not generally recom-

mended*

55°-65°

not generally recom-

mended*

20°-35

CA 1215-6 with

CA 1215-6

30° 40°

20°-30°

CA 1215-6 with

CA 1215-9

35° 45°

CA 1215-9 with

CA 1215-9

40°-50°

not generally

recommended*

50°-60°

not generally

recommended*

CA 1515-6 with

CA 1515-6

30° 40°

CA 1515-6 with

CA 1515-9

35° 45°

CA 1515-9 with

CA 1515-9

40°-50°

not generally recom-

mended*

50°-60°

not generally recom-

mended*

Application Increasing the horizontal

coverage angle, e.g. for

wide audience planes

Increasing the horizontal

coverage angle and sound

power level for larger dis-

tances

Increasing the vertical cov-

erage angle, e.g. for cover-

ing balconies or for in-

creased sound power level

for larger distances

Page 19

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

10.2.2 With rotated Horn

Horn

rotated

Standing

speaker

Winkel 2

Winkel 3

A smaller angle 3 results

in a smaller vertical cov-

erage angle but increases

the sound power level.

Winke l 1

Combination Angle 1 Angle 2 Angle 3

CA 1201 with

CA 1201

25° 35° Not recommended

CA 1215-6 with

CA 1215-6

20° 30°

30°-40°

CA 1215-6 with

CA 1215-9

30°-45°

CA 1215-9 with

CA 1215-9

Not recommended

CA 1515-6 with

CA 1515-6

30°-40°

CA 1515-6 with

CA 1515-9

30°-45°

CA 1515-9 with

CA 1515-9

Not recommended

Application Increasing the horizontal

coverage angle, e.g. for

wide audience planes

Increasing the horizontal

coverage angle and sound

power level for larger dis-

tances

Increasing the vertical

coverage angle, e.g. for

covering balconies or for

increased sound power

level for larger distances

Page 20

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

11.

11.11.

11. Wiring

The speaker is equipped with two parallel Speakon connectors.

Make sure that all units are switched off and all controls are turned down before connecting your CA systems.

− We recommend the use of high-quality speaker cables provided by KLING & FREITAG.

− For connections to the power amplifier inputs, please use 2-pin shielded microphone cable with high-

quality connectors.

− Avoid ground loops (see chapter 11.2)

− Please pay attention to the respective pin diagrams in this manual!

− Make sure that the +/- polarity of the speakers at the amplifier is correct. When simultaneously using

power amplifiers from different manufacturers, be sure to use the correct specific pin configuration. It may be necessary to modify the pin configuration on the power amplifiers or on the connectors leading to them.

− Upon completing the wiring, ensure that the connected speaker channels are working in phase. To do so, use i.e. a phase checker. A phase error can also be recognized when the connected channels are used simultaneously. During simultaneous use the bass frequencies become notably quieter or the midfrequencies such as voices cannot be located.

− To avoid loss of power, the cables should have a minimum wire gauge of 2.5 mm² - more for longer cabled distances. A minimum wire gauge can be easily calculated with the following formula:

If several loudspeakers are connected, the signal can be linked through from one louds

peaker t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

eaker t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

aker t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

ker t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

er t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

r t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

t o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

o the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

the next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

he next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

e next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

next . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

ext . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

xt . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

t . Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

. Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

Pl ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

l ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

ease make sur e that the t otal impedance of the l ouds p eakers R(

•) is

ase make sur e that the t otal impedance of the l ouds p eakers R(

•) is

se ma ke sur e that the t otal impedance of the l ouds p eakers R(

•) is

e make sur e that the t otal impedance of the l ouds p eakers R(

•) is

make sur e that the t otal impedance of the l ouds p eakers R(

•) is

make sur e that the t otal impedance of the l ouds p eakers R(

•) is

ake sur e that the t otal impedance of the l ouds p eakers R(

•) is

ke sur e that the t otal impedance of the l ouds p eakers R(

•) is

e sur e that the t otal impedance of the l ouds p eakers R(

•) is

sur e that the t otal impedance of the l ouds p eakers R(

•) is

sur e that the t otal impedance of the l ouds p eakers R(

•) is

ur e that the t otal impedance of the l ouds p eakers R(

•) is

r e that the t otal impedance of the l ouds p eakers R(

•) is

e that the t otal impedance of the l ouds p eakers R(

•) is

that the t otal impedance of the l ouds p eakers R(

•) is

that the t otal impedance of the l ouds p eakers R(

•) is

hat the t otal impedance of the l ouds p eakers R(

•) is

at the t otal impedance of the l ouds p eakers R(

•) is

t the t otal impedance of the l ouds p eakers R(

•) is

the t otal impedance of the l ouds p eakers R(

•) is

the t otal impedance of the l ouds p eakers R(

•) is

he t otal impedance of the l ouds p eakers R(

•) is

e t otal impedance of the l ouds p eakers R(

•) is

t otal impedance of the l ouds p eakers R(

•) is

t otal impedance of the l ouds p eakers R(

•) is

otal impedance of the l ouds p eakers R(

•) is

tal impedance of the l ouds p eakers R(

•) is

al impedance of the l ouds p eakers R(

•) is

l impedance of the l ouds p eakers R(

•) is

impedance of the l ouds p eakers R(

•) is

impedance of the l ouds p eakers R(

•) is

mpedance of the l ouds p eakers R(

•) is

pedance of the l ouds p eakers R(

•) is

edance of the l ouds p eakers R(

•) is

dance of the l ouds p eakers R(

•) is

ance of the l ouds p eakers R(

•) is

nce of the l ouds p eakers R(

•) is

ce of the l ouds p eakers R(

•) is

e of the l ouds p eakers R(

•) is

of the l ouds p eakers R(

•) is

of the l ouds p eakers R(

•) is

f the l ouds p eakers R(

•) is

the l ouds p eakers R(

•) is

the l ouds p eakers R(

•) is

he l ouds p eakers R(

•) is

e l ouds p eakers R(

•) is

l ouds p eakers R(

•) is

l ouds p eakers R(

•) is

ouds p eakers R(

•) is

uds p eakers R(

•) is

ds p eakers R(

•) is

s p eakers R(

•) is

p eakers R(

•) is

eakers R(

•) is

akers R(

•) is

kers R(

•) is

ers R(

•) is

rs R(

•) is

s R(

•) is

(

•) is

(

•) is •) is ) is is is s

not lower than the minimal impedance indicated on the power amplifier.

1/R1 + 1/R2 + 1/R3 + ... = 1/R

total

11.1 Connecting the Speakon Connector to the Terminal

Important

ImportantImportant

Important

Minimum Wire Gauge (mm²) =

Required Cable Length (m) 2 x Speaker Impedance (Ω)

Page 21

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

11.2 Avoiding Ground Loops

11.2.1 What is a Ground Loop?

Every component of a P.A. or Hi-Fi System has its own internal 0 V reference (ground). This point is often connected to the protective earth connector (PE / Ground). If two or more units are connected to one another with a line level audio cable, there may be a ground connection through the ground of the power supply cable (yellow-green) as well as through the shielding of the audio cable. The voltage difference between these two ground points causes audible interference to come from the speaker

11.2.2 Avoiding Ground Loops

If there is a loud humming or buzzing after the CA System has been connected, then check that a "ground loop" has not been built into the system. Some power amplifiers and system controllers are equipped with a "Ground Lift" switch. Set these switches to the "Lift" position one after the other. If the noise is still audible, check if,

1. the noise is caused by a ground loop before the power amplifiers / controllers (e.g. mixing console, ef- fects or equalizers).

2. the system or parts of the system are connected to an "unclean" power supply - meaning one, which is also running large motors, or lighting systems. An "unclean" supply voltage, electrostatic and electromagnetic fields can cause a malfunction.

Please observe the following basic rules:

Please observe the following basic rules:Please observe the following basic rules:

Please observe the following basic rules:

− Never!!! try to avoid a ground loop by disconnecting or taping the ground contact at the power connector! Extremely dangerous!

− If possible, only use high-quality audio appliances with balanced signal outputs and with power cables with PE connectors.

− Use high-quality cables with good shielding.

− The point of ground for all connected components should merge at one central point.

The power connections should lead out in a radial manner from one point and not be linked from one unit to the next.

− When installing appliances that create strong electrostatic or electromagnetic fields (large transformers, switch-mode power supplies), maintain some distance from other audio appliances. In extreme cases, the only solution is to create a completely independent "audio ground"; in other cases, it is sufficient to connect a filter in front of the audio equipment.

Warning

WarningWarning

Warning

Page 22

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

12.

12.12.

12. Configurations and Connecting Diagrams

12.1 Operating the Systems without K&F System Controller

The full-range systems can be used alone or in conjunction with a K&F subwoofer with integrated crossover (e.g. SW 112-XO / SW 115D-XO SW 115E-XO or SW 118E-XO). In this mode of operation the crossover limits the subwoofer's frequency range.

− To protect the speakers from being destroyed and to avoid fire hazard, they should only be operated with professional power amplifiers with the following specifications:

o integrated or preceding subsonic filter (approx. 30 Hz, min. 12 dB / oc-

tave)

o integrated clipping limiter o for speaker model CA 1201 or CA 1215:

aximum r ated power 500W@8• (e qui v al e

nt 1000W@4•)

ximum r ated power 500W@8• (e qui v al e

nt 1000W@4•)

imum r ated power 500W@8• (e qui v al e

nt 1000W@4•)

mum r ated power 500W@8• (e qui v al e

nt 1000W@4•)

um rated power 500W@8• (e qui val e

nt 1000W@4•)

m r ated power 500W@8• (e q ui v al e

nt 1000W@4•)

rated power 500W@8• (e qui v al e

nt 1000W@4•)

r ated power 500W@8• (e q ui v al e

nt 1000W@4•)

ated power 500W@8• (eq ui v al e

nt 1000W@4•)

ted power 500W@8• (e q ui v al e

nt 1000W@4•)

ed power 500W@8• (e qui val e

nt 1000W@4•)

d power 500W@8• (e q ui v al e

nt 1000W@4•)

power 500W@8• (e q ui v al e

nt 1000W@4•)

power 500W@8• (e qui val e

nt 1000W@4•)

ower 500W@8• (e q ui v al e

nt 1000W@4•)

wer 500W@8• (e q ui v al e

nt 1000W@4•)

er 500W@8• (e q ui v al e

nt 1000W@4•)

r 500W@8• (e q ui v al e

nt 1000W@4•)

500W@8• (e qui val e

nt 1000W@4•)

500W@8• (e q ui v al e

nt 1000W@4•)

00W@8• (e qui val e

nt 1000W@4•)

0W@8• (e qui val e

nt 1000W@4•)

W@8• (e qui v al e

nt 1000W@4•)

@8• (e qui v al e

nt 1000W@4•)

8• (e qui v al e

nt 1000W@4•)

• (e q ui v al e

nt 1000W@4•)

•

(e qui v al e

nt 1000W@4•)

(e q ui val e

nt 1000W@4•)

(

e q ui val e

nt 1000W@4•)

qui v al e

nt 1000W@4•)

ui val e

nt 1000W@4•)

i v al e

nt 1000W@4•)

val e

nt 1000W@4•)

al e

nt 1000W@4•)

l e

nt 1000W@4•)

t 1000W@4•)

1000W@4•)

000W@4•)

00W@4•)

0W@4•)0W@4•)W@4•)@4•)4•)•)

)

o for speaker model CA 1515:

ax i mum rated power 7

00W@8• (equivalent 1400W@4•)

xi mum r ated power 7

00W@8• (equivalent 1400W@4•)

i mum r ated power 7

00W@8• (equivalent 1400W@4•)

mum r ated power 7

00W@8• (equivalent 1400W@4•)

um rated power 7

00W@8• (equivalent 1400W@4•)

m r ated power 7

00W@8• (equivalent 1400W@4•)

rated power 7

00W@8• (equivalent 1400W@4•)

r ated power 7

00W@8• (equivalent 1400W@4•)

ated power 7

00W@8• (equivalent 1400W@4•)

ted power 7

00W@8• (equivalent 1400W@4•)

ed power 7

00W@8• (equivalent 1400W@4•)

d power 7

00W@8• (equivalent 1400W@4•)

power 7

00W@8• (equivalent 1400W@4•)

power 7

00W@8• (equivalent 1400W@4•)

ower 7

00W@8• (equivalent 1400W@4•)

wer 7

00W@8• (equivalent 1400W@4•)

er 7

00W@8• (equivalent 1400W@4•)

r 7

00W@8• (equivalent 1400W@4•)

0W@8• (equivalent 1400W@4•)

W@8• (equivalent 1400W@4•)

@8• (equivalent 1400W@4•)

8• (equivalent 1400W@4•)

• (equivalent 1400W@4•)

•

(equivalent 1400W@4•)

(

equivalent 1400W@4•)

quivalent 1400W@4•)

uivalent 1400W@4•)

ivalent 1400W@4•)

valent 1400W@4•)

alent 1400W@4•)

lent 1400W@4•)

ent 1400W@4•)

nt 1400W@4•)

t 1400W@4•)

1400W@4•)

400W@4•)

00W@4•)

0W@4•)

W@4•)

@4•)@4•)4•)•)

)

If you wish to use a speaker with a power amplifier which does not fulfil these specifications, then the speaker should be controlled using a Kling & Freitag System Controller with limiter function. This is the only way overloading and the risk of fire can be avoided. The results of such a power amplifier defect cannot be avoided by the controller.

12.1.1 CA Systems in Full-Range Mode

This mode of operation is ideal for speech applications and music applications without the need for a high bass content. Should more bass be needed, the bass level can be increased between 50 and 80 Hz at the mixing console.

INPUT CH 2 INPUT CH 1

OUTPUTS

CH 2 CH 1

INPUT e.g. from

mixer, AUX or

Connector Panel

If you are operating a mid-high system in a cluster (speakers arranged in close proximity) or as a stage monitor, reduce the frequencies below 300 Hz by 3-4 dB! (The K&F System Controllers have a special ‘Top Low Cut’ filter function for this purpose.)

Warning

WarningWarning

Warning

Page 23

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

12.1.2 Full Range Mode & Subwoofer with Crossover (XO)

In this mode of operation you can easily realise applications, where a higher bass level is needed.

In this mode of operation be sure to use only amplifiers, which can handle speaker impedances down to

3 •.

own t o

3 •.

wn to

3 •.

n to

3 •.

t o

3 •.

3 •.3 •. •.•.

Recommended combinations of CA systems, as described here, with K&F subwoo

Recommended combinations of CA systems, as described here, with K&F subwooRecommended combinations of CA systems, as described here, with K&F subwoo

Recommended combinations of CA systems, as described here, with K&F subwoof-

f-f-

ers:

ers:ers:

ers:

2 CA systems + 2- 4 x SW 112-XO

2 x SW 115D-XO

2 x SW 115E-XO

1 - 2 x SW 118E-XO

INPUT CH 2 INPUT CH 1

OUTPUTS

CH 2 CH 1

INPUT e.g. from

mixer, AUX or

Connector Panel

Switch To 'XO ON' Switch To 'XO ON'

The switch ‘XO’ on the connecting terminal of the subwoofer must be at XO ‘ON’ for this mode of operation:

Switch on the subwoofer’s connecting terminal

When using the mid-high systems in a cluster (speakers in close proximity), reduce the frequencies below 300 Hz by 3-4 dB. (The K&F System Controllers have a special ‘Top Low Cut’ filter function for this purpose.)

Important

ImportantImportant

Important

Page 24

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

12.2 Operations with K&F System Controller

For optimal performance and operating safety we recommend using a K&F system controller. Instructions for use, connecting diagrams and detailed descriptions of the latest controller models ‘CD 24’ and ‘CD 44’ you can find in the corresponding user’s manuals.

13.

13.13.

13. Operating the Speakers

− Switch off all equipment and turn down all level controls.

− Wire your CA systems.

− Pay attention to the user’s manuals of your power amplifiers.

− Upon completing the wiring, ensure that the connected speaker channels are working in phase. To do so,

use i.e. a phase checker. A phase error can also be recognized when the connected channels are used simultaneously. During simultaneous use the bass frequencies become notably quieter or the midfrequencies such as voices cannot be located.

− Now switch on the peripheral equipment first (mixing console, effects etc.), followed by the K&F system controller, if used, and the power amplifiers. Always use the before mentioned switching order. Otherwise switching noises may damage the system.

− If there is interference, turn off all appliances in the reverse order and check all cable connections.

− Successively turn up the individual power amplifier channels and send a signal with low volume to the

system. Check to see if the desired signals are applied to the intended speakers and make sure there is no interference. Make sure everything works properly, i.e. if the signals come from the correct speaker paths (high signals from the tweeters, bass signals from the bass speaker). Your system should now be ready for operation.

− Turning down the input level controls may not always prevent distortions in the input section of the pow- er amplifier, especially if this section has a relatively low headroom. A clipping signal may not be displayed by the clipping indicator then. To prevent signal interruptions from protection circuits or damages to the speakers, turn the level controls of the power amplifier to the maximum position, if possible. The output level of the mixing console or the controller should be set to a level that doesn't overload the power amplifiers.

− When turning off the system, the input controls for the power amplifiers should be turned down first followed by the power switches of the amplifiers. After that, the other appliances can be turned off.

− The crossovers of the CA systems are equipped with protection circuits for the high frequency driver and the crossover itself. These circuits cut off the signal current when highly overloaded. If the high speaker turns off, reduce the volume. After a few seconds, it will turn back on automatically.

Page 25

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.

14.14.

14. Crossovers

14.1 Wiring Diagram CA 1201

The crossover networks as of the end of 2003 differ from earlier models. Please compare the crossover built into your speaker with the figures below and wire accordingly:

14.1.1 Version A

CA 1201 & CA 1201-M up to serial no. 231 0000 20 29 (by the end of October 03)

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 26

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.1.2 Version B

CA 1201 & CA 1201-M from serial no. 231 0000 20 30 (as of the end of October 03)

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 27

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.2 Wiring Diagram CA 1215-6 and CA 1215 -9

The crossover networks as of the end of 2003 differ from earlier models. Please com-pare the crossover built into your speaker with the figures below and wire accordingly.

14.2.1 Version A

CA 1215-6 and CA 1215-6-M up to serial number 23090007055 (before Sept. 03)

CA 1215-9 and CA 1215-9-M up to serial number 23090002675 (before Sept. 03)

IN + / link to XO 2

IN - / Link to XO 2

IN-IN +

XO 2

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 28

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.2.2 Version B

CA 1215-6 and CA 1215-6-M from serial number 23090007056 up (as of Sept. 03)

CA 1215-9 and CA 1215-9-M from serial number 23090002676 up (as of Sept. 03)

HF -HF +

XO 2

XO 1

IN + / link to XO 2

IN - / Link to XO 2

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 29

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.3 Wiring Diagram CA 1515-6 and CA 1515-9

The crossover networks as of the end of 2003 differ from earlier models. Please compare the crossover built into your speaker with the figures below and wire accordingly.

14.3.1 Version A

CA 1515-6 and CA 1515-9 up to serial number 23116000434 (before November 03)

IN -IN +

HF +

LF +

LF -

HF -

XO 1

XO 2

IN + / link to XO 2

IN - / Link to XO 2

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 30

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

14.3.2 Version B

CA 1515-6 and CA 1515-9 from serial number 23116000435 (as of November 03)

IN + / link to XO 2

IN - / Link to XO 2

15.

15.15.

15. Touching Up Damage to Paint / Changing the Front Foam

Although the PU structured paint used by KLING & FREITAG is impact proof and extremely resistant, we recommend using protective coverings or cases to help avoid damaging the paint during i.e. continuous mobile use. If paint damage occurs despite these precautions, it can be touched up by using commercial acrylic paint in the appropriate RAL colour of the speaker.

To replace the filter foam, send the front grille incl. foam to KLING & FREITAG GmbH. Upon payment for expenses, the grille with the new covering will be returned.

Pin assignment Speakon NL4

+ - / /

‘IN’ 1+ 1- 2+ 2-

‘OUT’ parallel with ‘IN’

Page 31

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

16.

16.16.

16. Technical Specifications

16.1 CA 1201

Loudspeaker

Design 2-way passive system, bass reflex tuning

Frequency range -10 dB 54 Hz - 19 kHz

Frequency range ±3 dB 65 Hz - 18 kHz

Coverage angles nominal 90° x 60° (hor. x vert.)

Directivity index (DI) 10 (+1.5/-1) 1.2 kHz - 16 kHz

Power handling 300 W nominal1)

Max. SPL 126 dB (SPL peak / 1 m)

Components 12‘‘ low-mid chassis

1" high freq. driver with 40 mm titanium dome

on rotatable CD-horn

Crossover 1.8 kHz 18 dB / octave

self-resetting protection circuits for

12‘‘ and 1‘‘ chassis

Impedance (nominal) 8 •

Connectors 2 x Speakon NL4MP (1+ / 1-)

Enclosure

Trapezoidal enclosure with additional cluster angles,

15 mm Finnish birch Multiplex with highly

resistant black structured paint (PU),

2 butterfly handles,

mounting flange K&M 19656,

ball proof front grille with exchangeable

black acoustic foam

Rigging 5 flying points 'allsafe JUNGFALK'

Dimensions (W x H x D) 380 x 605 x 375 mm

Weight 25 kg

Options '48° monitor angle’ (K&F CA 1201 - M)

'100 Volt with 300 VA toroidal transformer’

‘Barrier strip instead of Speakon connectors'

'Outdoor Mobile' and 'Outdoor Installation'

‘Special finish in RAL colours’

Accessories see catalogue or visit www.kling-freitag.de

Page 32

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

16.2 CA 1215-6

Loudspeaker

Design 2-way passive system, bass reflex tuning

Frequency range -10 dB 62 Hz - 22 kHz

Frequency range ±3 dB 84 Hz - 19 kHz

Coverage angles nominal 65° x 50° (hor. x vert.)

Directivity index (DI) 12 (+1.5/-2) 1.2 kHz - 16 kHz

Power handling 400 W nominal1)

Max. SPL 130 dB (SPL peak / 1 m)

Components 12‘‘ low-mid chassis

1.5‘‘ high freq. driver with 75 mm titanium dome

on rotatable CD-horn

Crossover 1.2 kHz 12 dB / octave,

self-resetting protection circuits for

12‘‘ and 1.5‘‘ chassis, all-pass filter for

delay time and phase optimisation

Impedance (nominal) 8 • • •

Connectors 2 x Speakon NL4MP (1+ / 1-)

Enclosure

Trapezoidal enclosure with additional cluster angles,

15 mm Finnish birch Multiplex with highly

resistant black structured paint (PU),

2 butterfly handles,

mounting flange K&M 19656,

ball proof front grille with exchangeable

black acoustic foam

Rigging 5 flying points 'allsafe JUNGFALK'

Dimensions (W x H x D) 380 x 605 x 375 mm

Weight 31 kg

Options '48° monitor angle’ (K&F CA 1215-6 - M)

'100 Volt with 300 VA toroidal transformer’

‘Barrier strip instead of Speakon connectors'

'Outdoor Mobile' and 'Outdoor Installation'

‘Special finish in RAL colours’

Accessories see catalogue or visit www.kling-freitag.de

Page 33

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

16.3 CA 1215-9

Loudspeaker

Design 2-way passive system, bass reflex tuning

Frequency range -10 dB 58 Hz - 22 kHz

Frequency range ±3 dB 80 Hz - 19 kHz

Coverage angles nominal 90° x 50° (hor. x vert.)

Directivity index (DI) 10 (+2/-1) 1 kHz - 13 kHz

Power handling 400 W nominal1)

Max. SPL 129 dB (SPL Peak / 1 m)

Components 12‘‘ low-mid chassis

1.5‘‘ high freq. driver with 75 mm titanium dome

on rotatable CD-horn

Crossover 1.2 kHz 12 dB / octave,

self-resetting protection circuits for

12‘‘ and 1.5‘‘ chassis, all-pass filter for

delay time and phase optimisation

Impedance (nominal) 8 • • •

Connectors 2 x Speakon NL4MP (1+ / 1-)

Enclosure

Trapezoidal enclosure with additional cluster angles,

15 mm Finnish birch Multiplex with highly

resistant black structured paint (PU),

2 butterfly handles,

mounting flange K&M 19656,

ball proof front grille with exchangeable

black acoustic foam

Rigging 5 flying points 'allsafe JUNGFALK'

Dimensions (W x H x D) 380 x 605 x 375 mm

Weight 31 kg

Options '48° monitor angle’ (K&F CA 1215-9 - M)

'100 Volt with 300 VA toroidal transformer’

‘Barrier strip instead of Speakon connectors'

'Outdoor Mobile' and 'Outdoor Installation'

‘Special finish in RAL colours’

Accessories see catalogue or visit www.kling-freitag.de

Page 34

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

16.4 CA 1515-6

Loudspeaker

Design 2-way passive system, bass reflex tuning

Frequency range -10 dB 47 Hz - 22 kHz

Frequency range ±3 dB 77 Hz - 19 kHz

Coverage angles nominal 65° x 50° (hor. x vert.)

Directivity index (DI) 12 (+1.5/-2) 1.2 kHz - 16 kHz

Power handling 500 W nominal1)

Max. SPL 132 dB (SPL peak / 1 m)

Components 15‘‘ low-mid chassis

1.5‘‘ high freq. driver with 75 mm titanium dome

on rotatable CD-horn

Crossover 1.1 kHz 12 dB / octave, self-resetting

protection circuits for speakers and

crossover, all-pass filter for delay time and

phase optimisation

Impedance (nominal) 8 • • •

Connectors 2 x Speakon NL4MP (1+ / 1-)

Enclosure

Multi-purpose enclosure with monitor and

cluster angles, 15 mm Finnish birch Multiplex

with highly resistant black structured paint (PU),

2 butterfly handles,

mounting flange K&M 19656,

ball proof front grille with exchangeable

black acoustic foam

Dimensions (W x H x D) 433 x 680 x 410 mm

Weight 36.4 kg

Options '100 Volt with 300 VA toroidal transformer’

‘Barrier strip instead of Speakon connectors'

'Outdoor Mobile' and 'Outdoor Installation'

‘Special finish in RAL colours’

Accessories see catalogue or visit www.kling-freitag.de

Page 35

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

16.5 CA 1515-9

Loudspeaker

Design 2-way passive system, bass reflex tuning

Frequency range -10 dB 58 Hz - 22 kHz

Frequency range ±3 dB 75 Hz - 19 kHz

Coverage angles nominal 90° x 50° (hor. x vert.)

Directivity index (DI) 10 (+2/-1) 1 kHz - 13 kHz

Power handling 500 W nominal1)

Max. SPL 131 dB (SPL peak / 1 m)

Components 15‘‘ low-mid chassis

1.5‘‘ high freq. driver with 75 mm titanium dome

on rotatable CD-horn

Crossover 1.1 kHz 12 dB / octave, self-resetting

protection circuits for speakers and

crossover, all-pass filter for delay time and

phase optimisation

Impedance (nominal) 8 • • •

Connectors 2 x Speakon NL4MP (1+ / 1-)

Enclosure

Multi-purpose enclosure with monitor and

cluster angles, 15 mm Finnish birch Multiplex

with highly resistant black structured paint (PU),

2 butterfly handles,

mounting flange K&M 19656,

ball proof front grille with exchangeable

black acoustic foam

Rigging 5 flying points 'allsafe JUNGFALK'

Dimensions (W x H x D) 433 x 680 x 410 mm

Weight 36.4 kg

Options '100 Volt with 300 VA toroidal transformer

‘Barrier strip instead of Speakon connectors'

'Outdoor Mobile' and 'Outdoor Installation'

‘Special finish in RAL colours’

Accessories see catalogue or visit www.kling-freitag.de

Page 36

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

17.

17.17.

17. Measuring Charts

17.1 CA 1201

20 100 1000 10000 20000

100

Directivity Factor (Q)

Frequency (Hz)

Directivity Index DI (dB)

20 100 1000 10000 20000

100

110

Frequency response

Frequency (Hz)

SPL (dB)

3,16

31.6

100

Impedance

Impedance (Ohm)

20 100 1000 10000 20000

120

180

240

300

360

Horizontal Vertical

-6dB Beamwidth (degrees)

Frequency (Hz)

Frequency response

Beamwidth

Directivity

Page 37

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

125 250 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [Hz]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

125 250 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90°

-60°

-30°

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

Horizontal coverage

Vertical coverage

Page 38

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

17.2 CA 1215-6

20 100 1000 10000 20000

100

Directivity Factor (Q)

Frequency (Hz)

Directivity Index DI (dB)

20 100 1000 10000 20000

100

110

Frequency response

Frequency (Hz)

SPL (dB)

3,16

31.6

100

Impedance

Impedance (Ohm)

20 100 1000 10000 20000

120

180

240

300

360

Horizontal Vertical

-6dB Beamwidth (degrees)

Frequency (Hz)

Frequency response

Beamwidth

Directivity

Page 39

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

125 25 0 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

125 25 0 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

Horizontal coverage

Vertical coverage

Page 40

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

17.3 CA 1215-9

20 100 1000 10000 20000

100

Directivity Factor (Q)

Frequency (Hz)

Directivity Index DI (dB)

20 100 1000 10000 20000

100

110

Frequency response

Frequency (Hz)

SPL (dB)

3,16

31.6

100

Impedance

Impedance (Ohm)

20 100 1000 10000 20000

120

180

240

300

360

Horizontal Vertical

-6dB Beamwidth (degrees)

Frequency (Hz)

Frequency response

Beamwidth

Directivity

Page 41

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

125 250 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

125 250 500 1k 2k 4k 8k 16K

-180°

-150°

-120°

-90°

-60°

-30°

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

Horizontal coverage

Vertical coverage

Page 42

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

17.4 CA 1515-6

20 100 1000 10000 20000

100

Directivity Factor (Q)

Frequency (Hz)

Directivity Index DI (dB)

20 100 1000 10000 20000

100

110

Frequency response

Frequency (Hz)

SPL (dB)

3,16

31.6

100

Impedance

Impedance (Ohm)

20 100 1000 10000 20000

120

180

240

300

360

Horizontal Vertical

-6dB Beamwidth (degrees)

Frequency (Hz)

Frequency response

Beamwidth

Directivity

Page 43

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

125 250 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

125 250 500 1k 2k 4k 8k 16K

-180°

-150°

-120°

-90°

-60°

-30°

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

Horizontal coverage

Vertical coverage

Page 44

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

17.5 CA 1515-9

20 100 1000 10000 20000

100

Directivity Factor (Q)

Directivity Index DI (dB)

20 100 1000 10000 20000

100

110

Frequency response

Frequency (Hz)

SPL (dB)

3,16

100

Impedance

Impedance (Ohm)

20 100 1000 10000 20000

120

180

240

300

360

Horizontal Vertical

-6dB Beamwidth (degrees)

Frequency (Hz)

Frequency response

Beamwidth

Directivity

Page 45

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

125 250 500 1k 2k 4k 8k 16K

-18 0°

-15 0°

-12 0°

-90 °

-60 °

-30 °

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

125 250 500 1k 2k 4k 8k 16K

-180°

-150°

-120°

-90°

-60°

-30°

0°

30°

60°

90°

120 °

150 °

180 °

f [H z]

Attenuation (dB)

3 - 6

6 - 9

9 - 12

12 - 15

15 - 18

> 18

< 3

Horizontal coverage

Vertical coverage

Page 46

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.

18.18.

18. Dimensions

18.1 CA 1201, CA 1215-6 and CA 1215-9

5°

30°

172 mm

[6.772 inch]

256 mm

[10.079 inch]

172 mm

[6.771 inch]

61.3 mm

[2.412 inch]

605 mm

[23.819 inch]

378.5 mm

[14.903 inch]

375 mm

[14.763 inch]

183.2 mm

[7.211 inch]

189.3 mm

[7.451 inch]

189.3 mm

[7.451 inch]

302.5 mm [11.909 inch]

Rigging Points

ANCRA Jungfalk

120030-31

pole mount K&M 19656

Page 47

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.2 CA 1201-M, CA 1215-6-M and CA 1215-9-M

5°

48°

256 mm

Monitor Position

[10.079 inch]

172 mm

[6.771 inch]

61.3 mm

[2.412 inch]

605 mm

[23.819 inch]

378.5 mm

[14.903 inch]

374.1 mm

[14.729 inch]

189.3 mm

[7.451 inch]

174.1 mm

[6.855 inch]

302.5 mm [11.909 inch]

403 mm

[15.850 inch]

Rigging Points

ANCRA Jungfalk

120030-31

74°

136°

155°

172 mm

[6.772 inch]

Plastic Sliders

pole mount K&M 19656

Page 48

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.3 CA 1201, CA 1215-6 and CA 1215-9 with Option ‘Installation’

5°

30°

172 mm

[6.772 inch]

256 mm

[10.079 inch]

172 mm

[6.771 inch]

61.3 mm

[2.412 inch]

605 mm

[23.819 inch]

378.5 mm

[14.903 inch]

375 mm

[14.763 inch]

183.2 mm

[7.211 inch]

189.3 mm

[7.451 inch]

189.3 mm

[7.451 inch]

302.5 mm [11.909 inch]

7 x Rigging Point M 10

Page 49

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.4 CA 1515-6 and CA 1515-9

5°

48°

307.8 mm

[12.120 inch]

189.5 mm [7.461 inch]

62.9 mm

[2.476 inch]

680 mm

[26.772 inch]

433.6 mm

[17.073 inch]

411.3 mm

[16.195 inch]

216.8 mm

[8.536 inch]

212.3 mm

[8.358 inch]

340 mm

[13.386 inch]

Rigging Points

ANCRA Jungfalk

120030-31

189.5 mm [7.461 inch]

Plastic Sliders

pole mount K&M 19656

73°

137°

155°

Monitor Position

454 mm

[17.890 inch]

Page 50

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.5 CA 1515-6 and CA 1515-9 with Option ‘Installation’

5°

48°

307.8 mm

[12.120 inch]

189.5 mm [7.461 inch]

62.9 mm

[2.476 inch]

680 mm

[26.772 inch]

433.6 mm

[17.073 inch]

411.3 mm

[16.195 inch]

216.8 mm

[8.536 inch]

212.3 mm

[8.358 inch]

340 mm

[13.386 inch]

7 x Rigging Point M10

189.5 mm [7.461 inch]

73°

137°

155°

448 mm

[17.653 inch]

Monitor Position

Page 51

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

18.6 Accessories for the CA Systems

Tilt bracket CA 1201/CA1215 Cradle 1201/CA1215

CA 1515 Cradle 1515

Multi Cradle CA 1201/CA1215 Wall mount,

Multi Cradle CA 1515 tiltable up to 50 kg

Mounting bracket for versions with option ‚Installation’

Page 52

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

Tilt Bracket

Stand Adapter

Distance Rod

Distance rod & application examples TV-clamp TV-spigot single stud

with tilt bracket fitting

Further information is available in our downloadable catalogue at:

Page 53

User's Manual CA 1201, CA 1215-6 /-9, CA 1515-6 /-9

19.

19.19.

19. Disposal

Please recycle the packaging material of the device.

19.1 Germany

It is not allowed to dispose of used electrical equipment as domestic waste.

It is not allowed to dispose of used electrical equipment as domestic waste.It is not allowed to dispose of used electrical equipment as domestic waste.

It is not allowed to dispose of used electrical equipment as domestic waste.

But ple

But pleBut ple

But please do not dispose of them at official collecting points for recycling either!

ase do not dispose of them at official collecting points for recycling either!ase do not dispose of them at official collecting points for recycling either!

ase do not dispose of them at official collecting points for recycling either!

All KLING & FREITAG products are plain business-to-business (B2B) products. KLING & FREITAG products labelled with a waste bin sign have thus to be disposed of by KLING & FREITAG GmbH alone. Please call KLING & FREITAG at the number stated below if you have a KLING & FREITAG product to be disposed of. We will offer you a straightforward and professional disposal with no costs involved.

If there is no waste bin sign on one of your KLING & FREITAG products, because it has been sold before 24 March 2006, then by law the owner is in charge of the disposal. In this case we will be happy to assist and offer you proper ways of disposal.

Telephone number to call about the disposal of used

Telephone number to call about the disposal of usedTelephone number to call about the disposal of used

Telephone number to call about the disposal of used KLING & FREITAG products:

KLING & FREITAG products:KLING & FREITAG products:

KLING & FREITAG products:

+49 (0)

+49 (0)+49 (0)

+49 (0) 511

511511

511----96 99 7

96 99 796 99 7

96 99 7----0000

Explanation: With the ElektroG (law relating to electrical and electronic equipment and appliances) we have complied with the EU-directive on waste electrical and electronic equipment (WEEE, 2002/96/EC).

E From 03/24/2006 onwards KLING & FREITAG GMBH has thus labelled all products mentioned in the WEEE with a sign with a crossed out waste bin and a white bar below. This sign indicates that the disposal as domestic waste is prohibited and that the product has been put into circulation on 03/24/2006 at the earliest.

KLING & FREITAG GMBH has been legally registered as a manufacturer with the German registration office EAR. Our WEEE registration number is: DE64110372.

For the German Registration office EAR we have accredited that our products are soleB2B products.

19.2 EU, Norway, Iceland, and Liechtenstein

It is not allowed to dispose of used electrical equipment as domestic waste.

From 08/13/2005 onwards KLING & FREITAG GMBH has thus labelled all products for EUMember countries as well as Norway, Iceland and Liechtenstein (except Germany) mentioned in the WEEE with a sign with a crossed out waste bin and a white bar below.

E This sign indicates that the disposal on domestic waste is prohibited and that the product has been put into circulation on 08/13/2005 at the earliest.

Unfortunately the European directive WEEE has been complied with implementing different national provisions of law throughout all member countries, which makes it impossible for us to offer consistent solutions for the disposal throughout Europe.

Responsible for complying with these provisions of law is the local distributor (importer) of each country.

For proper disposal of used products in accordance with these local provisions in the mentioned countries of the European Union (except Germany) please ask your local dealer or the local authorities.

19.3 All other Countries

For proper disposal of used products in accordance with local provisions in other than the above mentioned countries please ask your local dealer or the local authorities.