Klimaire TNWT Installation Manual
WIRE CONTROLLER OF AIR CONDITIONER
INSTALLATION&
OWNER’ S MANUAL
MODEL: KJR-120C/TF-E(12V)
KJR-120C/TF-G(12V)
KJR-120C/TF-I(5V)
KJR-120C/TF-H(12V)
KJR-120C/TF-J(5V)
Thank you very much for purchasing our product.
Before using your unit, please read this manual carefully and keep it for future reference.
● This manual gives detailed description of the precautions
that should be brought to your attention during operation.
● In order to ensure correct service of the wired controller
please read this manual carefully before using the unit.
● For convenience of future reference, keep this manual
after reading it.
CONTENTS
1. SAFETY PRECAUTIONS......................................................................... 1
2. INSTALLATION ACCESSORY.................................................................. 2
3. INSTALLATION METHOD.........................................................................4
4. SPECIFICATION...................................................................................... 10
5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER................ 11
6. NAME ON THE LCD OF THE WIRE CONTROLLER............................ 12
7. NAME OF BUTTON ON THE WIRE CONTROLLER............................... 13
8. PREPARATORY OPERATION..................................................................15
9. OPERATION..............................................................................................16
10. TIMER FUNCTIONS................................................................................21
11. WEEKLY TIMER......................................................................................24
12. FAULT ALARM HANDING.......................................................................31
13.TECHNICAL INDICATION AND REQUIREMENT ...................................31
1. SAFETY PRECAUTIONS
g
Read the safety precautions carefully before installing the unit.
g
Stated below are important safety issues that must be obeyed.
WARNING
CAUTION
Means improper handling may lead to personal death or severe injury.
Means improper handling may lead to personal injury or property loss.
WARNING
Please entrust the distributor or professionals to install the unit.
Installation by other persons may lead to imperfect installation, lectric shock or ’ re.
Adhere to this installation manual.
Imporper installation may lead to electric shock or ’ re.
Reinstallation must be performed by professionals.
improper installation may lead to electric shock or ’ re.
Do not uninstall the unit randomly.
Random uninstalling may lead to abnormal operation, heating or ’ re of the air condition.
NOTE
1
Do not install the unit in a place vulnerable to leakage of ’ ammable gases.Once
’ ammable gases are leaked and left around the wire controller, ’ re may occure.
Do not operate with wet hands or let water enter the wire controller. Otherwise,
2
electric shock may occur.
3
The wiring should adapt to the wire controller current. Otherwise, electric leakage or
heating may occur and result in ’ re.
The speci’ ed cables shall be applied in the wiring. No external force may be applied
4
to the terminal. Otherwise, wire cut and heating may occur and result in ’ re.
1
2
2. INSTALLATION ACCESSORY
Select the installation location
Don’t install at the place where cover with heavy oil, vapor or sulfureted gas,
otherwise, this product would be deformed that would lead to system malfunction.
Preparation before installation
1. Please con×rm that all the following parts you have been supply.
No. Name Qty. Remarks
Wire controller
1
Installation and owner’s manual
2
Screws
3
Wall plugs
4
Screws
5
Plastic screw bars
6
The connective wires group
7
2. Prepare the following assemblies on the site.
No.
1
Switch box
Wiring Tube(Insulating
2
Sleeve and Tightening
Screw)
(For Mounting on switch box)
Name
1
1
M4X20
3
(For Mounting on the Wall)
For Mounting on the Wall
3
M4X25
2
For fixing on switch box
2
1
Optional
Qty.(embeded
into wall)
1
1
Specification
(only for reference)
Remarks
3
2. INSTALLATION ACCESSORY
Precaution of install the wire controller
1. This manual provides the installation method of wire controller. Please refer to the
wiring diagram of this installation manual to wire the wire controller with indoor unit.
2. The wire controller working in low voltage loop circuit. Forbid to directly contact the
cable of 220Vcommercial electricity or of 380V high voltage, and don’t wire this kind
of wire in the said loop; wiring clearance between con×gured tubes should at the
range of 300~500mm or above.
3. The Shielded wire of the wire controller must be grounded reliable.
4. Upon ×nish the wire controller connection, do not employed tramegger to detect the
insulation.
5. The connective cable of wire controller should not be longer than 20 meters.
4
3. INSTALLATION METHOD
1.Wired remote controller structure size ×gure
120
18.5
Fig 3-1
46
62
2.Wiring Principle Sketch:
Insert of the
red
black
yellow
brown
Wire controller
-----------------------------------
-----------------------------------
-----------------------------------
-----------------------------------
4-Core Shield Cable, the length
is decided by installation
Fig 3-2
mainboard CN40
red
black
yellow
brown
Indoor unit mainboard
3. INSTALLATION METHOD
5
3.Wiring figure
4-core shielding wire
The connective wires group
Connect the female joint of wires group from the mainboard with the male joint of
connective wires group. (See Fig.3-3)
Please connect the other side of connective wires group with the male joint of
wires group leads from wire controller. (See Fig.3-3)
4.Remove the upper part of wire controller
Insert a slot screwdriver into the slots in the lower
part of the wire controller (2 places), and remove
the upper part of the wire controller. (Fig.3-4)
NOTICE
The PCB is mounted in the upper part of the wire
controller. Be careful not to damage the board
with the slot screwdriver.
Slots
Fig 3-4
Mainboard
CN40
Fig 3-3
6
3. INSTALLATION METHOD
4. Fasten the back plate of the wire controller
For exposed mounting, fasten the back plate on the wall with the 3 screws (M4×20)
and plugs. (Fig.3-5)
Back plate
Screws (M4×20)
Fig 3-5
For ffush-mounting, fasten the back plate on the switch box with 2 screws (M4×25) and
fasten it on the wall with 1 screw (M4×20). (Fig.3-6)
Switch box
Back plate
Screw (M4×20)
Screws (M4×25)
Fig 3-6
NOTICE
Put on a ffat surface. Be careful not to distort the back plate of the wire controller
by overtightening the mounting screws.
7
3. INSTALLATION METHOD
5. Battery installation
Fig 3-7
Put the battery into the installationsite and make sure the positive side of the battery
is in accordance with the positive side of installationsite.(See Fig.3-7)
Please set the time corrected on the ffrst time operation. Batteries in the wire
controller can timing under power failure which ensure the time keep right. When
the power restores, if the time displayed is not correct, it means the battery is dead
and replace the battery.
3. INSTALLATION METHOD
6. Wiring
Left side
wire outlet
Top side
wire outlet
Right side
wire outlet
A. For exposed mounting, four outletting positions.
There are three need cutting.
Embedded switch
box wiring
Wiring
hole
Bottom side
wire outlet
B.Shielded wiring
Wiring through the wall
Wall hole and wiring hole
Fig 3-9
Diameter of wall hole：Φ20mm
Cutting place of top
side wire outlet
Fig 3-8
Cutting place of left
side wire outlet
Putty
CAUTION
Avoid the water enter into the wired remote controller, use trap and putty to seal the
connectors of wires during wiring installation. (Fig.3-10)
When under installation, reserve certain length of the connecting wire for convenient
to take down the wired remote controller while during maintenance.
8
Trap
Cutting place of right
side wire outlet
Putty
Trap
Fig 3-10
Putty
Trap
Loading...