Page 1
AIR CONDITIONER
REMOTE CONTROLLER
AUTO
COOL
DRY
HEAT
FAN
MODE
M
FAN SPEED
ILLUSTRATION
Thank you very much for purchasing our air conditioner.
Please read this owner's manual carefully before using
your air conditioner.
Page 2
Page 3
Remot e Con trolle r Spe cificat ions
Model
Rated Voltage
Lowest Voltage of
CPU Emitting Signal
Signal Receiving
Range
Environment
RG05F2/BGEU1
3.0V(Dry batteries R03/LR03 2)
2.4V
8m
O O O O
23 F~140 F(-5 C~60 C)
Perfor manc e Featur e
1. Operating Mode: AUTO, COOL, DRY, HEAT(cooling & heating models only),
and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 6 2 F~86 F(17 C~30 C).
O O O O
4. Full function of LCD (Liquid Crystal Display).
AUTO
COOL
DRY
HEAT
FAN
MODE
FAN SPEED
M
Sliding door
(closed)
33
Page 4
Funct ion bu ttons
AUTO
COOL
DRY
HEAT
FAN
1
MODE
2
M
FAN SPEED
3
4
SWIN G V SLEEP
SWIN G H
I FEE L
SELF CL EAN
RESET LO CK
TUR BO
LED
5
6
7
8
TIMER ON
TIMER OFF
CLOCK
ON/OFF Button
1
Operation starts when this button is pressed
and stops when this button is pressed again.
MODE Button
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
AUTO
NOTE: Please do not select HEAT mode if the
COOL
DRY
machine you purchased is cooling only type. Heat
9
mode is not supported by the cooling only
appliance.
HEAT FAN
10
3
11
12
13
14
15
16
SLEEP Button
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, FAN
SPEED or ON/OFF button is pressed.
4
SWING V Button
Used to stop or start horizontal louver movement and set the desired up/down air flow
direction. Push once, the louver changes 6
degree in angle. Keep pushing more than 2
seconds, the louver will swing up and down
automatically.
Sliding door
(opened)
5
SWING H Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press.If keep pushing more than 2
seconds,the vertical louver swing feature is
activated.(Not applicable to all the units,please
refer to the OWNER S MANUAL for details).
I FEEL /SELF CLEAN Fun ction
6
Press this button less than 2 seconds will
initiate I FEEL function. And if keep pressing
this button more than 2 seconds, the
SELF CLEAN function is initiated.
44
Page 5
Funct ion bu ttons (cont inued )
AUTO
COOL
DRY
HEAT
FAN
1
MODE
2
M
FAN SPEED
9
10
3
4
5
6
7
8
SWIN G V SLEEP
TUR BO
SWIN G H
I FEE L
LED
SELF CL EAN
RESET LO CK
TIMER ON
TIMER OFF
CLOCK
11
12
7
13
14
15
16
8
9
10
When the I FEEL function is activated, the
remote display is actual temperature at its
location. The remote control will send this
signal to the air conditioner every 3 minutes
interval until press the I FEEL button again.
This indicator light remains on.
The I FEEL function is not available under
DRY and FAN mode.
Switch the operation mode or turn off the unit
will cancel the I FEEL function automatically.
Under SELF CLEAN mode, the air conditioner
will automatically clean and dry the Evaporator
and keep it as fresh for the next operation.
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
LOCK Button
Press this recessed button to lock all current
settings, and the remote controller will not
accept any operation except that of the LOCK.
Use the LOCK mode when you want to prevent
settings from being changed accidentally.
Press the LOCK button again to cancel the
LOCK function. A lock symbol will appear on
the remote controller display when the lock
function is activated.
FAN SPEED Button
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
UP Button
Push this button to increase setting temperature
or to increase Hour during Clock time setting.
11
DOWN Button
Push this button to decrease setting temperature
or to decrease Hour during Clock time setting.
NOTE: Press and hold UP and DOWN buttons
together for 3 seconds will alternate the temperature display between the C & F scale.
O O
55
Page 6
1
2
3
4
5
6
7
8
AUTO
COOL
DRY
HEAT
FAN
MODE
M
SWIN G V SLEEP
TUR BO
SWIN G H
I FEE L
LED
SELF CL EAN
RESET LO CK
FAN SPEED
TIMER ON
TIMER OFF
CLOCK
12
TIMER ON Button
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-on time setting, just press the button until
the time setting is 0.0.
13
TIMER OFF Button
Press this button to activate the Auto-off time
9
10
11
12
13
14
15
16
setting. Each press will increase the time setting
in 30 minutes increments, up to 10 hours, then at
1 hour increments up to 24 hours. To cancel the
Auto-off time setting, just press the button until
the time setting is 0.0.
13
14
TURBO
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperature
in the shortest time. When press this button
on heating mode(applicable to the unit adopts
PTC only), the PTC will be energized and bring
fast heating operation.
15
CLOCK Button
Used to set the remote clock.
LED Button
16
Disable/Active indoor screen Display.
NOTE:
Buttons design might be slightly different
from the actual one depending on individual
models.
All the functions described above are
accomplished by the indoor unit, if the
indoor unit has no this feature, there is no
corresponding operation happened when
press the relative button on the remote
controller.
Please do not select HEAT mode if the
machine you purchased is cooling only
type. Heat mode is not supported by the
coolingonly appliance.
66
Page 7
Indica tors on LC D
AUTO
COOL
DRY
HEAT
FAN
TEMP.
SET
CLOCK
TIMER
HOUR
ON OFF
Mode display
Displays the current operation mode. Including
AUTO( ), COOL( ), DRY( ), HEAT( )
(Not applicable to cooling only models), FAN( )
and back to AUTO( ).
AUTO
Transmission Indicator
This transmission indicator lights when remote
controller transmits signals to the indoor unit.
ON/OFF display
Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to remove.
Temp. display
Displays the temperature setting(62F ~86F /17C ~
O
30C ). When you set the operating mode to FAN, no
O O O
temperature setting is displayed.
Time display
Indicate Timer on/off time(0~24 hours) or clock
time. The clock time is indicated only when no AUTO-
FF
ON/OFF timer is set. When AUTO-TIMER feature is
operating, it displays the AUTO-ON/OFF time. To
check the current time, press the CLOCK button, and
the time will display.
Fan speed display
Displays the selected fan speed, AUTO( ) and three
fan speed levels " " (LOW) " " (MED)
" " (HIGH) can be indicated. The fan speed
is auto controlled under AUTO or DRY mode.
Lock Display
Displayed when LOCK mode is activated.
Sleep Display
Displayed under sleeping operation.
Press the SLEEP button again to remove.
I FEEL Display
Displayed when I FEEL function is activated.
Note:
All displays on the remote controller are
shown for illustration purposes only.
77
Page 8
AUTO
TEMP.
COOL
SET
DRY
CLOCK
TIMER
HEAT
FAN
MODE
M
SWIN G V SLEEP
TURB O
SWIN G H
I FEEL
LED
SELF CL EAN
RESET LOC K
HOUR
ON OFF
FAN SPEED
TIMER ON
TIMER OFF
CLOCK
How to use t he bu ttons
Before you start operating the air conditioner, set
the clock of the remote controller using the procedures given in this section. The clock panel on the
remote controller will display the time regardless of
whether the air conditioner is in use or not.
Initial Setting the Clock
After batteries are inserted in the remote controller,
the clock panel will display "12:00" and begin to flash.
1. UP/DOWN button
.
Press these buttons to set time.
1
Forward.
Backward.
.
Each time you press the button, the time moves
forward or backward by one minute depending
2
on which side you press. The time alters as quickly
as you push the button.
.
Keep pressing the button without releasing, the
time moves forward or backward by 10 minutes
depending on which side you press.
2.
CLOCK button
When the right time is achieved, press the CLOCK
button or release the or and wait for 5
seconds, the clock time stops flashing and the
clock starts operating.
3.Readjusting the Clock
Press the CLOCK button on the remote controller,
the time of the clock display will start to flash. To
set the new time, follow 1 and 2 of "Initial Setting
of the Clock".
Note: The time of the CLOCK must be set before
the AUTO-TIMER feature will operate.
* Clock accuracy is within 15 seconds per day.
!
CAUTION
Static electricity or other factors (Voltage transients) can
cause the remote controller clock to initialize. If your
remote controller is initialized (the time of "12:00"
flashing), readjust the clock before starting the unit.
88
Page 9
Auto o perat ion
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
AUTO
TEMP.
COOL
SET
DRY
CLOCK
HEAT
HOUR
FAN
1
MODE
M
FAN SPEED
3
display panel of the indoor unit starts flashing.
1. Press the MODE button to select Auto.
2. Press the UP/DOWN button to set the
desired temperature. The temperature can
be set within a range of 62F~86 F in 1F
O O O
increments.
3. Press the ON/OFFbutton to start the air
conditioner.
2
NOTE
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, and Heating
by sensing the difference between the actual
ambient room temperature and the setting
temperature on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
Coolin g /Hea ting/Fa n ope ration
AUTO
TEMP.
COOL
SET
DRY
CLOCK
HEAT
HOUR
FAN
MODE
1
M
FAN SPEED
4
Ensure the unit is plugged in and power is
available.
1. Press the MODE button to select COOL, HEAT,
(cooling & heating models only) or FAN mode.
2. Press the UP/DOWN buttons to set the
desired temperature.
3
be set within a range of 62F~86 F in 1F
The temperature can
O O O
increments.
3. Press the FAN SPEEDbutton to select the
fan speed in four steps- Auto, Low, Med,or
2
High.
4. Press the ON/OFF button to start the air
conditioner.
NOTE
In the FAN mode, the setting temperature is not
displayed in the remote controller and you are not able
to control the room temperature either. In this case,
only step 1, 3 and 4 may be performed.
99
Page 10
Dehum idifyin g ope ration
Ensure the unit is plugged in and power is
available. The OPERATION indicator on the
AUTO
TEMP.
COOL
SET
DRY
CLOCK
HEAT
HOUR
FAN
MODE
1
M
FAN SPEED
3
display panel of the indoor unit starts flashing.
1. Press the MODE button to select DRY mode.
2. Press the UP/DOWN buttons to set the
desired temperature.
be set within a range of 62F~86 F in 1F
The temperature can
O O O
increments.
3. Press the ON/OFF button to start the air
conditioner.
2
NOTE
In the Dehumidifying mode, you can not switch the
fan speed. It has already been automatically controlled.
Adjus ting a ir flow dire ction
Use the SWING V button to adjust the desired
airflow direction.
When push the SWING V button, the horizontal
louver changes 6 degree in angle for each push.
Keep pushing more than 2 seconds, the louver
will swing automatically and give UP and
DOWN air flow.
NOTE: When the horizontal louver swing
or move to a position which would affect
the cooling or heating effect of the air
conditioner, it would automatically change
the swing/moving direction.
1010
Page 11
Timer oper ation
press the TIMER ON button can set the auto-on
time of the unit. And press the TIMER OFF button
can set the auto-off time of the unit.
AUTO
TEMP.
COOL
SET
DRY
CLOCK
TIMER
HEAT
FAN
MODE
M
SWIN G V SLEEP
TURB O
SWIN G H
I FEEL
LED
SELF CL EAN
RESET LOC K
HOUR
ON OFF
FAN SPEED
TIMER ON
TIMER OFF
CLOCK
To set the Auto-on time.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "HOUR" will be shown
on the LCD display area. Now it is ready to reset
the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases in 30 minutes increments, up
1
to 10 hours, then at 1 hour increments up to 24
hours.
2
3. After setting the TIMER ON ,there will be a one half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "HOUR" will disappear and the set temper ature will re-appear on the LCD display window.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "HOUR" will be shown
on the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button,
the time increases in 30 minutes increments, up
to 10 hours, then at 1 hour increments up to 24
hours.
3. After setting the TIMER OFF ,there will be a one half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "HOUR" will disappear and the set temper ature will re-appear on the LCD display window.
1111
Page 12
IMPORTANT
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
Exam ple of Time r sett ing
TIMER ON
(Auto-on Operation)
TIMER
HOUR
ON
The TIMER ON feature is useful when you want
the unit to turn on automatically before say when
you return home. The air conditioner will automatically start operating at the set time.
Start
Off
Example:
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of
Set
6 hours later
starting operation time and the signal "HOUR" will
show on the display area.
2. Press the TIMER ON button to display "6.0" on
the TIMER ON display of the remote controller.
3. Wait for 3 seconds and the TIMER ON indicator
stops flashing and this function is activated. The
digital display area will show the tempera ture
again.
1212
Page 13
TIMER
HOUR
OFF
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to turn off automatically after you go to bed.
The air conditioner will stop automatically at the set
time.
Stop
On
Set 10 hours later
TIMER
HOUR
ON OFF
2 hours later
after setting
Stop
10 hours later
after setting
On
Set
Start
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "HOUR" will
show on the display area.
2. Press the TIMER OFF button to display "10" on
the TIMER OFF display of the remote controller.
3. Wait for 3 seconds and the TIMER OFF indicator
stops flashing and this function is activated. The
digital display area will show the temperature
again.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to
display 2.0 HOUR on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to
display 10 HOUR on the TIMER ON display .
5. Wait for the remote control to display
the setting temperature.
1313
Page 14
TIMER
Off
Set
HOUR
2 hours later
after setting
ON OFF
Start
Stop
5 hours later
after setting
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
Example:
To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to
display 2.0 HOUR on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to
display 5.0 HOUR on the TIMER OFF display .
5. Wait for the remote control to display
the setting temperature.
1414
Page 15
The Klimaire logo is a registered Trademark of Klimaire Products inc.
Copyright 2010 Klimaire Products inc.
2190 NW 89 Place, Doral, FL 33172 - USA
Tel: (305)594-4972 Fax (305) 499 4378
www.klimaire.com sales@klimaire.com
The design and specifications are subject to change without prior notice
for product improvement. Consult with the sales agency or manufacturer
for details.
Loading...