Klimaire KJR12B Specifications
KJR-12B Wired Remote Control Wall ThermostatKJR-12B Wired Remote Control Wall ThermostatKJR-12B Wired Remote Control Wall Thermostat
1
Operation mode indication:
When press " MODE " button, the follow-
ing mode can be selected in circle. Auto
→Cool →Dry→Heat→Fan only→Auto.
For cooling only model,heat mode is
skipped.
2
Timer :
When adjust setting on time or only on
time is set, the "ON" is lighted.
When adjust setting off time or only off
time is set , the "OFF" is lighted. If on
and off timer are both set, the"ON" and
"OFF"are both lighted.
Operation mode indication
Timer ON/OFF
MODE BUTTON
TIMER ON BUTTON
TIMER OFF BUTTON
FOLLOW ME BUTTON
ELECTRICAL
HEATER BUTTON
3
Follow me function:
There is a temperature sensor inside the
wire controller, after setting temperature,
it will compare the two temperatures,
and the space of wire controller will be
the same as setting temperature. It is
available under cooling, heating, auto
mode.
4
: ON/OFF indication :
When it is on, the icon display,
otherwise it is extinguished.
5
; Fan speed indication :
There are four fan modes : low, middle,
high, auto. For some models, no middle
fan then the middle fan is seen as high
speed.
6
< Lock:
When the " LOCK " button is pressed,
the icon appear and other buttons is
unable, press again, the icon disappear.
7
= Temperature display zone:
Generally it displays setting tempera-
ture, it can be adjusted by press
temperature button ▲ and ▼. But in fan
mode, no display here.
ON / OFF BUTTON
7
1
3
Follow me function
4
2
1
2
1
2
3
4
5
ON/OFF indication
5
Fan speed indication
Lock
6
Temperature display zone
7
ADJUST BUTTON
8
9
ADJUST BUTTON
SWING BUTTON
10
ECONOMY BUTTON
11
RESET BUTTON
Mode botton:
1
When press this botton,the operation
mode change as the following
sequence:
:
→AUTO → COOL→DRY→HEAT→FAN
Remark: For the cooling only model, the
heating mode is skipped.
Timer on button :
2
Press this button, timer on function is
active. Then every press, the time
increase 0.5h, after 10h, 1h
increasement after each press. If cancel
this Function, just set it to "0.0" .
3
Timer off button:
Press this button, timer off function is
active.Then every press, the time
increase 0.5h, after 10h, 1 h
increasement after each press. If
6
All the pictures in this manual are for explanation purpose only. There may be
slightly different from the wire controller you purchased(depend on model). The
actual shape shall prevail.
cancel this function, just set it to "0.0" .
4
Follow me button :
When under cool, heat and auto mode,
press this button, follow me function is
active. Pressing the ON/OFF button or
MODE button will not cancel the Follow
me feature. This function is disable
when the unit is off or under DRY or FAN
mode. Pressing the FOLLOW ME button
again will cancel the follow me feature.
; Electrical heater button :
5
If press this button in heat mode, electri-
cal heater function become ineffective.
< Reset button(hidden):
6
Use a 1mm stick to press in the little hole,
then the current setting is canceled. The
wire controller enter into original state.
FAN SPEED BUTTON
12
13
= ON/OFF button:
7
When in off state, press this button, the
indicator is on, the wire controller enter
into on state, and send setting information
to in door Pcb. When in on state,press this
button, the indicator is off, and send
instruction. If timer on or timer off has
been set, it concel this setting then send
instruction to stop the machine.
Adjust button ▲:
>
8
Set indoor temperature up. If press and
hold on, it will increase at 1°C(1°F) per
0.5 second.
Adjust button ▼ :
9
Set indoor temperature down. if press and
hold on, it will decrease at 1°C(1°F) per
0.5 second.
LOCK BUTTON
Loading...