Klimaire KDIP24H2, KDIR12H2 User Manual

Wired Remote ControlWired Remote ControlWired Remote Control

Operation mode indication:

When press " MODE " button, the follow-

ing mode can be selected in circle. Auto

→Cool →Dry→Heat→Fan only→Auto.

For cooling only model,heat mode is

skipped.

Timer :

When adjust setting on time or only on

time is set, the "ON" is lighted.

When adjust setting off time or only off

time is set , the "OFF" is lighted. If on

and off timer are both set, the"ON" and

"OFF"are both lighted.

Operation mode indication

Timer ON/OFF

MODE BUTTON

TIMER ON BUTTON

TIMER OFF BUTTON

FOLLOW ME BUTTON

ELECTRICAL HEATER BUTTON

Follow me function:

There is a temperature sensor inside the

wire controller, after setting temperature,

it will compare the two temperatures,

and the space of wire controller will be

the same as setting temperature. It is

available under cooling, heating, auto

mode.

: ON/OFF indication :

When it is on, the icon display,

otherwise it is extinguished.

; Fan speed indication :

There are four fan modes : low, middle,

high, auto. For some models, no middle

fan then the middle fan is seen as high speed.

< Lock:

When the " LOCK " button is pressed,

the icon appear and other buttons is

unable, press again, the icon disappear.

= Temperature display zone:

Generally it displays setting tempera-

ture, it can be adjusted by press

temperature button ▲ and ▼. But in fan

mode, no display here.

ON / OFF BUTTON

Follow me function

ON/OFF indication

Fan speed indication

Lock

Temperature display zone

ADJUST BUTTON

SWING BUTTON

ECONOMY BUTTON

RESET BUTTON

Mode botton:

When press this botton,the operation

mode change as the following

sequence:

→AUTO → COOL→DRY→HEAT→FAN

Remark: For the cooling only model, the

heating mode is skipped.

Timer on button :

Press this button, timer on function is

active. Then every press, the time

increase 0.5h, after 10h, 1h

increasement after each press. If cancel

this Function, just set it to "0.0" .

Timer off button:

Press this button, timer off function is

active.Then every press, the time

increase 0.5h, after 10h, 1 h

increasement after each press. If

All the pictures in this manual are for explanation purpose only. There may be slightly different from the wire controller you purchased(depend on model). The actual shape shall prevail.

cancel this function, just set it to "0.0" .

Follow me button :

When under cool, heat and auto mode,

press this button, follow me function is

active. Pressing the ON/OFF button or

MODE button will not cancel the Follow

me feature. This function is disable

when the unit is off or under DRY or FAN

mode. Pressing the FOLLOW ME button

again will cancel the follow me feature.

; Electrical heater button :

If press this button in heat mode, electri-

cal heater function become ineffective.

< Reset button(hidden):

Use a 1mm stick to press in the little hole,

then the current setting is canceled. The

wire controller enter into original state.

FAN SPEED BUTTON

= ON/OFF button:

When in off state, press this button, the

indicator is on, the wire controller enter

into on state, and send setting information

to in door Pcb. When in on state,press this

button, the indicator is off, and send

instruction. If timer on or timer off has

been set, it concel this setting then send

instruction to stop the machine.

Adjust button ▲:

Set indoor temperature up. If press and

hold on, it will increase at 1°C(1°F) per

0.5 second.

Adjust button ▼ :

Set indoor temperature down. if press and

hold on, it will decrease at 1°C(1°F) per

0.5 second.

LOCK BUTTON

NOTE: Press and hold UP and DOWN

buttons together will alternate the

temperature display between the °C & °F

scale.

Swing button:

Used to set the airflow direction. Hold

down this button for 2 seconds to

activate auto swing feature.

Economy operation button :

press this button, the indoor unit

operates in economy mode, press again,

exit this mode (it may be ineffective for

some models)

Fan speed button:

press this button consecutively, the fan

speed will circle as follow:

Lock button(hidden):

When you push the LOCK button, all

current settings are locked in and the

wire controller does not accept any

operation except that of the LOCK

button. Use the lock mode when you

want to prevent setting from being

changed accidentally or play fully. Push

the LOCK button again when you want

to cancel the LOCK mode.

USING METHOD

AUTOMATIC OPERATION

Connect to power,indoor operation lamp

flash.

1. Press "MODE" button, select " AUTO "

;

temperature you want, generally it is

among 17°C(62°F)~30°C(86°F);

3. Press " ON/OFF" button, operation

lamp is on, the air-conditioner work in

auto mode, indoor fan is auto, and can

not be changed. Auto is displayed on

LCD. Press ON/OFF button again to stop.

4. Economy operation is valid in auto

mode.

5. In event of power interruption such as

a blackout, the air conditioner stops once.

But it restarts automatically and performs

previous operation when the power

supply is resumed.

COOL/HEAT/FAN MODE OPERATION

1. Press "MODE" button, select "COOL"

, "HEAT" or "FAN ONLY" mode.

2. Press temperature adjust button to

select setting temp.

3. Press "FAN SPEED" button to select

high/mid/low/auto.

4. Press "ON/OFF" button, indoor unit

operation lamp on, it works in selected

mode. Press "ON/OFF" button again, it

stops to work.

Remark: When in fan mode, no

temperature can be set.

DRY OPERATION

1. Press " MODE " button, select " DRY "

mode.

2. Press temperature adjust button to

select setting temp.

3. Press " ON/OFF " button, indoor unit

operation lamp on, it works in dry mode.

Press ON/OFF button again, it stops to

work.

4. In dry mode, economy operation and

fan speed are ineffective.

TIMER SETTING

Timer on only:

1. Press " TIME ON " button, it display

"SET" on LCD, and display " H " and "ON"

, it is waiting for timer on setting.

2. Press " timer " on button repeatedly to

adjust time setting.

3. If press this button and hold on, the

time will increase at 0.5h, after 10h, it

increase at 1h.

4. After setting 0.5 second, the wire

controller send timer on information, it is

finished.

Timer off only:

1. Press "TIME OFF " button, it display

"SET" on LCD, and display " H " and ON,

it is waiting for timer on setting.

2. Press "TIME OFF" button repeatedly to

adjust time setting.

3. If press this button and hold on , the

time will increase at 0.5h, after 10h, it

increase at 1h.

4. After setting 0.5 second, the wire

controller send timer off information, it is

finished.

TIMER ON AND TIMER OFF BOTH

1. Set timer on time as the

corresponding step1 and 2.

2. Set timer off time as the

corresponding step1 and 2.

3. Timer off time must be longer than

timer on time.

4. 0.5 second after setting, the wire

controller send information.the setting is

finished.

CHANGE TIMER

If there is a need of changing timer

time, press corresponding button to

revise it. If concel timer, change timer

time to 0.0.

TIMER

AUXIL

HEATER

MODE

LOCK

RESET

OFF

FANSPEED

SWING

ECO

TEMP

Klimaire KDIP24H2, KDIR12H2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual