PF705 Manual Sealless Steel Strapping Tool
9422-H0317
SPECIFICATIONS
1. Strap Dimensions: Widths: 13mm (1/2”), 16mm (5/8”), 19mm (3/4”) Thickness : 0.38mm (.015”) – 0.70mm (0.27”)
2. Weight: 3.5 kg
SAFETY INSTRUCTIONS
1. Always read operating instructions before using the tool.
2. Always wear eye, face and hand protection when operating the tool.
3. Keep hands/fingers or other parts of the body away from areas that can be pinched or cut.
MAINTENANCE INSTRUCTIONS
1. Clean this tool periodically with compressed air to remove any dust or dirt. The punch (#10), dies (#21 and #22),
gripper (#8) and feedwheel (#59) must be cleaned regularly.
2. Apply light machine oil to all moving parts.
3. Check tool regularly for broken or worn parts.
4. Use the original replacement parts to ensure tool reliability.
OPERATING INSTRUCTIONS
Prior to operation, make sure the front strap stop (#13), side strap stop (#91 for 16mm and 19mm, #92 for 13mm and
19mm), and rear strap stop (#36 for 16mm and 19mm, #37 for 13mm and 16mm) are equivalent to your strap width.
(See ADJUSTMENTS-TO ADJUST STRAP STOPS for installation of strap stops)
1. Feed the strapping around the
package and hold in place with left
hand. The end of strap is underneath.
2. Pull the feedwheel handle (#58) toward the sealing handle
(#73) with your right hand. While in this position, insert
the strap into the sealing section against the front strap stop
(#13) so the strap sits inside the side strap stop (#91 or #92).
The end of strap should protrude 1” beyond the front strap
stop (#13). Release the feedwheel handle (#58) so the strap is
locked and ready to be tightened.
5. Move the sealing handle (#73) back to its original posi-
tion. Hold the cut off strap end with the left hand. Lift the
feed wheel handle (#58) toward the sealing handle (#73) to
release the strap. Slide the tool away to the right.
STRAP MUST SIT INSIDE THE SIDE STRAP STOP
INSERT THE STRAP INTO THE SEALING SECTION AGAINST THE WALL OF HOUSING
3. Hold the sealing handle (#73) firmly with left hand.
Pump the tensioning handle (#82) with your right hand
until the desired tension is reached.
4. Place right hand firmly on the tensioning handle (#82) for
supporting the tool. Move the sealing handle (#73) all the way
forward until it hits the stop (#51). This seals and cuts the strap.
ADJUSTMENTS
TO ADJUST STRAP STOPS (All front, side and rear strap stops must set in the same number prior to use)
13mm (1/2”)
16mm (5/8”)
19mm (3/4”)
FRONT STRAP STOP #13 SIDE STRAP STOP #91 AND #92 REAR STRAP STOP #36 AND #37
TO ADJUST FRONT
AND REAR STRAP
STOPS
Loosen screws (#14)
in front of and behind
the housing (#39). Put
the size you want in
place and retighten
the screws (#14).
TO ADJUST SIDE
STRAP STOP
Loosen screws (#94
and #96). Put the size
you want in place and
retighten the screws
(#94 and #96).
TO ADJUST FEEDWHEEL HANDLE
SPRING (#56)
(To increase gripping
performance of
feedwheel #59)
Turn the socket set
screw (#15) with
hexagon key clockwise
to increase gripping
performance.
TO ADJUST SEALING DEPTH
(To avoid cutting strap too deep
or fail to cut the strap)
Loosen nut (#52), turn stop
(#51) counterclockwise to
decrease sealing depth and
cutting depth, or turn clockwise
to increase sealing depth and
cutting depth, then retighten
the stop (#51) and nut (#52).
TO ADJUST GAP
BETWEEN THE
FEEDWHEEL (#59)
AND GRIPPER (#8)
(To prevent the
strap from slipping)
ADJUST GRIPPER ADJUST FEEDWHEEL
9422-H0317
PARTS LIST
9422-H0317
Part
No. Description Qty.
Part
No. Description Qty.
01 Base 1 49 Side Plate 1
02 Pin 2 50 Screw 3
03 Pin 1 51 Stop 1
04 Socket Set Screw 3 52 Nut 2
05 Screw 2 54 Bolt 2
06 Socket Set Screw 1 55 Washer 2
07 Bolt 1 56 Feedwheel Handle Spring 1
08 Gripper 1 58 Feedwheel Handle 1
10 Punch 1 59 Feedwheel 1
11 Screw 1 60 Tension Shaft 1
12 Socket Set Screw 2 61 Double Circle Key 1
13 Front Strap Stop 1 62 Strap Guide 1
14 Screw 2 64 Washer 1
15 Socket Set Screw 1 66 Retaining RIng 1
17 Cutter Support 1 67 Retaining Ring 1
18 Sealing Handle Shaft 1 69 Head Bolt 1
19 Roller 1 70 Parallel Pin 1
20 Roller Pin 1 71 Socket Set Screw 1
21 Die 1 73 Sealing Handle 1
22 Die 1 75 Sealing Cam 1
23 Link 1 76 Pin 2
24 Screw 4 80 Shim (0.35mm thickness) 2
25 Cutter 1 81 Shim (0.15mm thickness) 1
27 Pin 1 82 Tensioning Handle 1
31 Ejector 1 84 Washer 1
32 Pressure Spring 1 86 Tensioning Handle Stop 1
34 Screw 2 91 Side Strap Stop ( For 16 and 19mm strap) 1
36 Rear Strap Stop (For 16 and 9mm strap) 1 92 Side Strap Stop (For 13 and 16mm strap) 1
37 Rear Strap Stop (For 13 and 16mm strap) 1 93 Bushing 1
39 Housing 1 94 Screw 1
41 Trunnion 1 95 Pin 1
42 Pin 2 96 Screw 1
45 Cover 1 102 Washer 1
46 Parallel Pin 1 103 Washer 1
47 Cover Spring 1 110 Base Protector 1
48 Bushing 1
PARTS LIST Cont’d
Loading...