Klein Tools MM1000 User Manual

ENGLISH

Duty

ºF º

REL

RANGE

HOLD

MIN/MAX

1000V

10A

6. Frequency (Hz) / Duty Cycle < 1MHz Features:

Duty

7. Temperature Features:

Duty

•

• Fahrenheit range: -58° to 1832°F

• Celsius range: -50° to 1000°C

Testing Fuses

SELECT

• “O.L.” indicates blown fuse.

.L.

MIN

°F

n m M

HOLD

ºF º

PRESS

Hz Duty

MAX/MIN REL HOLD

ºF º

PRESS

°F °C

Do not apply voltage to thermocouple.

PRESS

Duty

SYMBOLS USED ON LCD

AC Measurement DC Measurement Negative DC Value Overload: Range Exceeded Low Battery Minimum Reading Duty Cycle Mode Frequency Mode Voltage Measurement Resistance in Ohms Relative Reading Capacitance in Farads Diode Test Degrees Fahrenheit Continuity Test

-9

Nano 10

-3

Milli 10

Mega 10

ºF º

Duty

COM

ºF º

Duty

COM

Auto Range Active

Auto Power-Off Active

Apo

HOLD

Hold Active Maximum Reading

Current in Amps

Degrees Celsius

°C

Micro 10

Kilo 10

ELECTRICAL SPECIFICATIONS

DC Voltage Measurement

Range Resolution Accuracy

400mV ˜ 400V 0.1mV ˜ 0.1V ± (0.5% + 4 digits) 1000V 1V ± (0.8% + 10 digits)

Overload Protection: 1000 V Input Impedance (Nominal): > 10 MΩ, < 100 pF

AC Voltage Measurement

Range Resolution Accuracy

400mV ˜ 400V 0.1mV ˜ 0.1V ± (0.75% + 5 digits) 40Hz ˜ 400Hz 1000V 1V ± (1.0% + 8 digits) 40Hz ˜ 400Hz

Overload Protection: 1000V RMS Input Impedance (Nominal): > 10MΩ, < 100pF Response: Averaging

DC Current Measurement

Range Resolution Accuracy

400µA ˜ 400mA 0.1µA ˜ 0.1mA ± (1.0% + 5 digits) 4A ˜ 10A 1mA ˜ 10mA ± (1.5% + 5 digits)

Overload Protection:

• µAmA Input: 400mA (F 440mA / 1000V fuse)

• A Input: 10A (F 11A / 1000V fuse)

AC Current Measurement

Range Resolution Accuracy

400µA ˜ 400mA 0.1µA ˜ 0.1mA ± (1.5% + 5 digits) 4A ˜ 10A 1mA ˜ 10mA ± (2.0% + 5 digits)

Overload Protection:

• µAmA Input: 400mA (F 440mA / 1000V fuse)

• A Input: 10A (F 11A / 1000V fuse)

Frequency: 40Hz to 400Hz Response: Averaging

Temperature Measurement

Range Resolution Accuracy

-58 ˜ 1832°F 0.1 ~ 1°F ± (3.0% + 5.4°F)

-50 ˜ 1000°C 0.1 ~ 1°C ± (3.0% + 3.0°C)

Overload Protection: 600V RMS Thermocouple Accuracy: Not specified

Diode Test

Overload Protection Test Current (Typical) Open Circuit Voltage Range

600V RMS 0.25mA

1.6V DC 2.0V DC

Continuity Test

Overload Protection Open Circuit Voltage

600V RMS Appx. 0.44V

WARRANTY

www.kleintools.com/warranty

CLEANING

Turn instrument off and disconnect test leads. Clean the instrument by using a damp cloth. Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when instrument is not in use for a prolonged period of time. Do not expose to high temperatures or humidity. After a period of storage in extreme conditions exceeding the limits mentioned in the Specifications section, allow the instrument to return to normal operating conditions before using it.

DISPOSAL / RECYCLE

Caution: This symbol indicates that equipment and its accessories shall

be subject to a separate collection and correct disposal.

Instruction Manual

ENGLISH

• AUTO / MANUAL RANGE

• MAX / MIN

• BAR GRAPH

• DATA HOLD

• 3-3/4 DIGIT 3999 COUNT LCD

• BACKLIGHT

• LEAD HOLDER

Resistance Measurement

Range Resolution Accuracy

400Ω ˜ 4MΩ 0.1Ω ˜ 0.001MΩ 40M

Ω 0.01MΩ

± (1.0% + 5 digits) ± (1.5% + 10 digits)

MM1000

Apo

0 10 20 4030

MAX/MIN

RANGE

REL

SELECT

Duty

ºF º

COM

MM1000

HOLD

Temp

Overload Protection: 600V RMS

Capacitance Measurement

Range Resolution Accuracy

40nF 0.01nF 400nF ˜ 4000µF 0.1nF ˜ 1µF

± (3.5% + 6 digits)

Overload Protection (Voltage): 600V RMS

Frequency Measurement

Range Resolution Accuracy

-6

9.999Hz ˜ 999.9kHz 0.001Hz ˜ 0.1kHz ± (0.1% + 3 digits)

Overload Protection: 600V RMS Sensitivity: 0.7V RMS

Duty Cycle Measurement

Range Resolution Accuracy

0.1 ˜ 99.9% 0.1% ± (0.2% per kHz + 0.1% + 5 digits)

Overload Protection: 600V RMS Frequency Range: 0.5Hz to 100kHz, pulsewidth > 2μsec

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

www.kleintools.com

139543T Rev. 11/13 B

ENGLISH

ºF º

Duty

ºF º

Duty

ºF º

200m

10A

BATT.

MM1000

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools MM1000 is an auto-ranging multimeter. It measures AC/DC voltage, AC/DC current, resistance, capacitance, frequency, duty cycle, and temperature. It can also test diodes and continuity.

• Operating Altitude: 2000 m

• Relative Humidity: < 75%

• Operating Temperature: 0°C / 32°F to 40°C / 104°F

• Storage Temperature: -20°C / -4°F to 60°C / 140°F < 80% R.H.

• Accuracy Temperature: 18°C / 64°F to 28°C / 82°F

• Temperature Coefcient: 0.1*(specified accuracy) / °C

• Sampling Frequency: 3 samples per second

• Dimensions: 7" x 3.5" x 1.875" (178 mm x 89 mm x 48 mm)

• Weight: 14 oz. (397 g)

• Calibration: Accurate for one year

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 2 m (6 ft.)

• Safety Rating: CATIII 1000V, CAT IV 600V

WARNINGS

To ensure safe operation and service of the tester, follow these instructions. Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the category based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep fingers away from the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes are connected.

• Use caution when working with voltages above 60V DC, or 25V AC RMS. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace batteries if a low battery indicator appears.

• Unless measuring voltage or current, shut off and lock out power before measuring resistance or capacitance.

• Always adhere to local and national safety codes. Use individual protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.

SYMBOLS

AC Alternating Current Warning or Caution

DC Direct Current Double Insulated Class II

DC/AC Voltage or Current AC Source

Ground

FEATURE DETAILS

H. Max / Min Hold

• Press to enter Max / Min mode; the largest and smallest values will be saved while in this mode.

• Press repeatedly to alternate between the maximum and minimum readings.

J D

Apo

MM1000

• Press for 2 seconds to return to live reading and clear the stored maximum and minimum values.

I. Hold / Backlight

• Press to hold the current input on the display.

• Press again to return to live reading.

• Press for 2 seconds to enable/disable lights.

0 10 20 4030

G F

REL

SELECT

RANGE

Duty

MAX/MIN

ºF º

HOLD

• Using lights drains the battery significantly.

J. K. Battery / Fuse Replacement

• When

indicator is displayed on the LCD, batteries must

be replaced.

• Remove rubber boot, back screw, and replace 2 x AAA batteries.

• This meter uses 440mA / 1000V and 11A / 1000V fast blow fuses.

L. Magnetic Hanger Accessory (optional, sold separately)

• Slide magnetic adapter into protective rubber boot.

• Attach instrument to metal for hands-free use.

M. Bar Graph

C B

Temp

COM

• The bar graph shows an approximate analog representation of a measurement.

• The bar graph responds much faster than the digital display.

• The scale of the bar graph is zero to the maximum reading of the selected range.

FUNCTION INSTRUCTIONS

5 6

FEATURE DETAILS

A. B. C.

Use CAT III / CAT IV rated leads. A. Do not attempt to measure more than 1000V. B. Do not attempt to measure more than 400mA.

4 1

Duty

C. Do not attempt to measure more than 10A. D. Auto Power-Off (Apo)

• Device will power off after 30 minutes non-use.

• Turn the dial or press a button to wake.

• Disabled during Max / Min function.

• Holding Select button while turning on disables Auto Power-Off.

E. Select Functionality Button

• Switch between AC and DC.

• Switch between

Ω, , and .

Hz and %. °F and °C.

1. AC / DC Voltage: < 1000V

Duty

REL HOLD

PRESS

Features:

F. Relative Reading Mode

• Press to store current value.

• Display will now show the difference between the stored and live readings.

• Press again to return to live reading.

G. Auto / Manual Range

• Select AC or DC voltage source.

ºF º

MAX/MINRANGE

1.5V

200

20k

200k

200m

COM

600V MAX

250mA/250V

3 2

2. AC / DC Current (large): < 10A

ºF º

REL HOLD MAX/MINRANGE

PRESS

Features:

• Start with this setting if current level is unknown.

• Attach red lead to “

A” input.

• Select AC or DC current source.

3. AC / DC Current (small): < 400mA Features:

ºF º

REL HOLD MAX/MINRANGE

PRESS

• Attach red lead to “mAµA” input.

• Select µA or mA, and AC or DC current source.

4. Resistance / Diode / Continuity

Duty

COM

TO SELECT

Resistance

Diode

Continuity

Resistance Features:

HOLD RANGE

•

Do not measure resistance

on a live circuit.

•

40M

COM

Diode Features:

MAX/MIN

HOLD

Display shows:

• Forward voltage drop if forward biased.

• “O.L.” if reverse biased.

COM

Continuity Features:

HOLD

MAX/MIN

Display shows: Resistance

• Buzzer sounds if less than 30

5. Capacitance: < 4000µF

Duty

HOLD

ºF º

Duty

ºF º

COM

Features:

COM

MAX/MIN

PRESS

REL

• Press repeatedly to cycle through manual ranges.

• Press for 2 seconds to return to auto ranging mode.

•

AT is displayed on LCD only during auto ranging mode.

• Safely discharge capacitor before measurement.

• Reading may take up to 60 seconds for large capacitors.