Klein Tools KN1500P-EX, KN1600P-EX, KN1500P-EXH Instruction Manual
INSTRUCTION MANUAL
KN1500P-EX
WEB-STRAP RATCHET HOIST
KN1600P-EX
WEB-STRAP RATCHET HOIST DELUXE
KN1500P-EXH
WEB-STRAP RATCHET HOIST WITH HOT RINGS
KN1500P-EXH
KN1500P-EX
KN1600P-EX
ENGLISH
ESPAÑOL PG. 13
FRANÇAIS PG. 25
ENGLISH
2
GENERAL SPECIFICATIONS
The Klein Tools KN1500P-EX, KN1500P-EXH, AND KN1600P-EX meet ASME B30.21-2014 standard for Manually Lever
Operated Hoists (Web Strap Type) and ASME B30.10-2014 standard for hooks.
Single Line
Load Rating: 1500 lbs. (675 kg)
Pulling Distance: Max: 138" (3500 mm)
Min: 20" (500 mm)
Double Line
Load Rating: 3000 lbs. (1350 kg)
Pulling Distance: Max: 79" (2000 mm)
Min: 26" (700 mm)
DANGER:
The hoist is NOT an insulating member. Use an appropriate insulating member in series with the hoist to
achieve proper working distances per OSHA Regulation Subpart V, 1926.950 or follow your company’s
work practices.
Use appropriate clothing and gloves for rated voltage if handle must swing closer to
energized lines than specified by OSHA or your company.
WARNINGS
For KN1500P-EX, KN1500P-EXH and KN1600P-EX:
• Failure to comply with the following instructions could result in serious injury or death.
• Do not attempt to adjust, repair, or modify any part of the hoist.
• Do not lift more than the rated load.
• Do not operate hoist when it is restricted from forming a straight line with the direction of loading.
• Do not operate hoist with a twisted, kinked, or damaged web strap.
• Do not operate a damaged or malfunctioning hoist.
• Do not lift using hoist.
• Do not use hoist to lift people.
• Do not use hoist to lift loads over people.
• Do not operate hoist with a lever extension.
• Do not remove or obscure warning labels.
Additionally, for KN1500P-EXH:
• Hot rings are NOT load rated for pulling.
• Hot rings will NOT prevent electrical shock and are intended to be used with hot sticks.
Additionally, for KN1600P-EX:
• Do not use hoist with any handle other than the one specified by manufacturer.
OSHA REGULATION SUBPART V, 1926.950 TABLE V-1
Alternating Current - Minimum Distances
Voltage Range
(Phase to Phase)
Kilovolt
Minimum
Working
Distance
Voltage Range
(Phase to Phase)
Kilovolt
Minimum
Working
Distance
2.1 to 15 2 ft. 0 in. 161 to 169 3 ft. 8 in.
15.1 to 35 2 ft. 4 in. 230 to 242 5 ft. 0 in.
35.1 to 46 2 ft. 6 in. 345 to 362 7 ft. 0 in.
46.1 to 72.5 3 ft. 0 in. 500 to 552 11 ft. 0 in.
72.6 to 121 3 ft. 4 in. 700 to 765 15 ft. 0 in.
138 to 145 3 ft. 6 in.
3
BEFORE OPERATING & HANDLING THE LOAD
Before operating the hoist ensure that:
• The supporting structure or anchoring means have the same or greater load capacity as the hoist.
• The operator has read and understood all information included in this manual, and are familiar with the
operating controls, hoisting practices, and warnings associated with the hoist.
• If any adjustments or repairs to the hoist are needed, report them promptly to a designated person.
• Hoist shall only be used in locations where the operator can be free of the load.
• The operator shall not use a hoist with an out-of-order sign.
• The operator shall not attempt to adjust or repair a hoist, unless qualified to make such adjustments or repairs.
• Hoists shall only be operated by the hand power of one person.
• Hoists shall not be operated with an extension on the handle.
• Removable handle (on Cat. No. KN1600PEX) is fully seated and snaps into place.
While handling the load, ensure that:
• The hoist web strap is not wrapped around the load.
• The load is attached to the load hook by suitable means.
• The sling or other device is properly seated in the base (bowl) of the hook. The latch shall not be allowed to
support any part of the load.
• The load is not applied to the point of the hook.
• Before applying the load, the operator shall be sure the web strap is not twisted or that multiple parts of the web
strap are not twisted around each other.
• The hoist shall not be operated until the load block, web strap, and hoist body are directly in line with the
direction of loading to avoid sidepull.
• The hoist body or frame is not bearing against any object or the supporting structure.
• The operator shall not apply a load beyond the rated load appearing on the hoist or load block, except during
properly authorized tests.
• Specific attention should be given to balancing of the load and hitching or slinging to prevent slipping of the load.
• The operator shall not release the hoist lever until the ratchet and pawl is engaged and the lever is at rest.
• The operator shall not engage in any activity that will divert the operator’s attention while operating the hoist.
• The operator shall not apply a load to the hoist until the operator and all other personnel are clear of the load.
• The operator shall make sure the load clears any obstacles before moving.
• The load shall not be moved more than a few inches until it is well balanced in the sling or lifting device.
• When starting to lift or pull, the operator should move the load a few inches and then check the hoist for proper
load holding action. The operation shall be continued only after the operator has verified the hoist is operating
properly.
• Hoist shall not be used to lift, support, or otherwise transport people.
• The operator shall not pull or hold loads over people.
• The operator should not leave a loaded hoist unattended unless specific precautions have been instituted and
are in place.
• Care shall be exercised when removing a sling from under a landed and blocked load.
ENGLISH
4
FEATURES (ALL MODELS)
HOT RINGS (KN1500P-EXH ONLY
)
Floating Hook
Web Strap
Drum Knob
Brake Wheel
Handle
Fixed Hook
Hook
Pawl
Ratchet
Switch
Hook Hot Ring
Fixed Hook Hot Ring
Floating Hook
Hot Ring
Ratchet Switch Hot Ring
Handle Hot Ring
• All hot rings are intended to support the weight of the hoist (13 lbs 6 oz - 0.623 kg).
• The hook hot rings are designed to aid in positioning and attaching the hooks
onto hardware and grips when used with hot sticks.
• The Ratchet switch hot ring is designed to aid in switching the hoist
from the “D”, “N”, and “U” positions while using a hot stick.
• The handle hot ring is designed to aid in letting out and taking up slack
when used with a hot stick.
5
REMOVABLE HOOK AND HANDLE (KN1600P-EX ONLY
)
Removable Hook
Removable Handle
ENGLISH
6
OPERATING INSTRUCTIONS
Rigging the Hoist for Single or Double Line Pull
1. Single Line – Only the fixed end hook should be attached to the load.
WARNING: Do NOT attach floating hook to a load for a single line pull.
WARNING: Never rig web strap in a choke position by attaching the two hooks to each other.
WARNING: Ensure sling or other device is properly seated in the bowl of the hook, and the
hook latch is securely closed before pulling. Do not use the hook latch to support
any part of the load.
2. Double Line –
Fixed end hook should be attached to the eye on the puller body. Floating hook should be
attached to the load.
Reinstalling the Floating Hook
1. Insert inner bushing (long metal cylinder) into outer bushing (black nylon cylinder), and place one washer on each
side of the bushings.
2. Position washers and bushings on the inside of the hook clevis, and align all the holes.
3. Insert bolt through clevis, washers and bushings. Bolt end with hole should be visible on the other side of clevis.
4. Tighten wing nut on exposed bolt end with hole.
5. Insert straight side of cotter pin into bolt hole, until it snaps into place.
Pulling Out the Web Strap
1. To release tension on the web strap, shift ratchet switch toward the “D” on the handle.
2. Use handle to ratchet the web strap forward or off the drum.
3. For faster payout, switch the ratchet to neutral or the “N” position, disengage the pawl from the brake wheel with
one hand, and pull the web strap with the other hand.
CAUTION: When in use, leave no less than two wraps of the web strap on the drum while pulling.
CAUTION: When web strap is fully paid out, do NOT attempt to further unwind the strap. This could
result in damage to the web strap and/or brake mechanism.
Adding Tension on the Web Strap With a Load Attached:
1. Move ratchet to up or the “U” position.
2. Use the handle to ratchet the web strap upwards, or towards the “U”. Continue to ratchet up until there is no longer
any slack in the strap.
Releasing Tension on the Web Strap With a Load Attached:
1. Switch the ratchet to the down or “D” position.
2. Ratchet down until you feel the tension brake release (typically after one full ratchet).
3. Once the tension brake is released, continue to ratchet down until you can safely unhook the load.
CAUTION: Do NOT unhook the load or otherwise release tension while the ratchet switch is in the up
or “U” position. Doing so will cause the brake mechanism to lock. (If locked, put tension
back on the web strap. Switch the ratchet to the down or “D” position and ratchet down
to release the tension brake).
7
OPERATING INSTRUCTIONS
Rewinding the Web Strap
1. To rewind the web strap, shift ratchet switch toward the “U” on the handle.
2. Use handle to ratchet the web strap back onto the drum. NOTE: If there is no tension on the web strap, it is
recommended to use the drum knob to wind up the strap.
3. For faster return, shift ratchet switch to neutral or the “N” position, and manually rotate the drum knob in the
direction of the “U” or up position.
WARNING: Do NOT attempt to manually unwind the drum if a load is attached.
WARNING: If the strap is wound in the wrong direction, the hoist WILL NOT hold a load, and the strap will
unwind when tension is applied.
CAUTION: Ensure the take-up of the web strap onto the drum is always in the up direction,
or towards the “U”.
The web strap must be wound in the proper direction for the hoist to function properly. If the strap is wound
incorrectly the hoist WILL NOT hold a load and the strap will unwind when tension is applied. This can happen when
the strap is unwound completely and rewound in the wrong direction.
When the web strap is completely spooled out, turn the knob or handle in the counterclockwise direction (“U” direction
marked on knob) to rewind the web strap. When attempting to rewind in the wrong direction, a warning label will be
exposed. See below.
CORRECT winding direction
Correct knob rotation
Strap should wind "overhand"
INCORRECT winding direction
Strap incorrectly wound "underhand"
WARNING LABEL
Shows when winding in wrong direction
ENGLISH
8
HOIST INSPECTION
Frequent and Periodic inspections of the web strap hoist must be performed at the intervals described below to ensure
proper operation and safety of the hoist.
Frequent Inspections require a visual examination (records not required) by the operator or other designated person.
If conditions are found during inspection that constitutes a hazard, the designated person shall determine if a more
detailed inspection is required. Frequent inspections should be performed at the following intervals:
• Normal Service – monthly
• Heavy Service – weekly to monthly
• Severe Service – daily to weekly
• Special or infrequent service – as recommended by a qualified person before and after each occurrence.
• Hoists that have been idle for one month or more, but no more than one year shall under-go a frequent inspection
before put back into service.
Periodic Inspections require a visual inspection by a designated person who records the external conditions of
the hoist to provide a basis for continuing inspection. If conditions found during inspection constitute a hazard, a
designated person shall determine if disassembly of the hoist is required. Periodic inspections should be performed at
the following intervals:
• Normal Service – yearly
• Heavy Service – semi-annually
• Severe Service – quarterly
• Special or infrequent service – as recommended by a qualified person before the first such occurrence and as
directed by the qualified person for any subsequent occurrence.
• Hoists that have been out of service for one year or more shall under-go a periodic inspection before put back
into service.
The following charts detail the items that are required to be inspected during Frequent and Periodic inspections.
NOTE: For your convenience, several pages are included at the end of this instruction manual to record all periodic
inspections and servicing.
Inspection Item
Normal Service Heavy Service Severe Service
Visual
Monthly
Record
Yearly
Visual
Weekly to
Monthly
Record
Semi
Annually
Visual
Daily to
Weekly
Record
Quarterly
Frequent Inspection
All functional mechanisms for
maladjustment and unusual sounds
• • •
Hooks (as designated in this manual)
• • •
Hook latch operation, if used
• • •
Web strap (as designated in this manual)
• • •
Lever for bends, cracks, etc.
• • •
Hoist support for damage
• • •
9
HOIST INSPECTION
Inspection Item
Normal Service Heavy Service Severe Service
Visual
Monthly
Record
Yearly
Visual
Weekly to
Monthly
Record
Semi
Annually
Visual
Daily to
Weekly
Record
Quarterly
Periodic Inspection
Requirements of frequent inspection
• • •
Evidence of loose bolts, nuts, or rivets
• • •
Evidence of worn, corroded, cracked,
or distorted parts such as load blocks,
suspension housing, levers, web
strap attachments, clevises, yokes,
suspension bolts, shafts, gears,
bearings, pins, rollers, and locking and
clamping devices
• • •
Evidence of damage to hook retaining
nuts or collars, and pins and welds
or rivets used to secure the retaining
members
• • •
Evidence of damage or excessive wear
of load sprockets
• • •
Evidence of worn pawls, cams, or
ratchets; corroded, stretched, or broken
pawl springs
• • •
Label designating load rating
• • •
End connections and terminations of
web strap
• • •
WARNING: If service becomes necessary on the web strap hoist, all repairs MUST be made by Klein Tools
or an authorized repair center. See Warranty/Repairs section of this manual for more information.
ENGLISH
10
WEB STRAP INSPECTION
Web straps also require Frequent and Periodic inspections.
Frequent Inspections: Web straps should be visually inspected before each use. The operator or other designated
person should look for signs of:
• In-Service date on strap tag is filled in
• Melting or charring
• Acid or caustic burns
• Weld spatter
• Broken stitching
• Cuts or tears
• Damaged eyes or fittings
• Abrasive wear
• Knots
WARNING: If any of the conditions above exist on the web strap, remove from service immediately and contact
Klein Tools or authorized repair center to replace the web strap.
Periodic Inspections: The frequency of these inspections should be determined by a qualified person and based on
factors such as usage, environment, and previous experience. Inspections are not required at equal intervals, and
should be more frequent as the web strap approaches the end of its useful life.
CAUTION: We recommend increased frequency of inspections if any of the following conditions are detected:
• Severely worn end connections
• Distortion of the web strap structure
• Evidence of heat damage
WARNING: Web strap should be replaced, regardless of condition, five (5) years after the hoist went into service.
HOOK INSPECTION
Frequent and Periodic Inspections of the hooks should be performed at the same time those inspections are performed
on the hoist. Hooks should be removed from service, and repaired or replaced, if any of the below conditions exist:
• Cracks, nicks, and gouges
• Any visibly apparent bend or twist from the plane of the unbent hook
• Any distortion causing an increase in throat opening
• Any damaged latch or malfunctioning latch that does not close the hook’s throat
• Evidence of excessive heat exposure or unauthorized welding
• Evidence of unauthorized alterations such as drilling, machining, grinding, or other modifications
• Any missing nuts, bolts, fasteners, retaining pins or rings
HOIST MAINTENANCE
• Avoid storing web strap hoist in areas that are: high in humidity, dusty, sandy, exposed to direct sunlight.
• If hoist is used in heavy rain or near saltwater, clean all parts of the hoist (except handle and web strap) with a
multi-purpose lubricant.
• Do not allow water to come in contact with the brake area. Water contact could cause the brake to become stiff
or malfunction. If this occurs, the unit may require a factory overhaul before storage or returning to service.
11
WEB STRAP MAINTENANCE
Store web strap protected from dirt, oil, water, and other foreign materials that could damage the strap or cause deterioration.
Inspect for evidence of exposure to excessive heat, charring, acid burns, chemical contamination or excessive
abrasion as follows:
Type of
Material
Exposure to
Excessive Heat
Exposure to
Chemicals
Exposure
to Molten
Metal or
Flame
Exposure to Paints
or Solvents
Exposure Near
Live Electrical
Lines and
Equipment
Polyester Poor resistance.
Fibers become
brittle and will
shrivel, turn
brown in color,
and break when
flexed. Should not
be used above
180°F (82°C).
Good Resistance to most chemicals,
including hydrochloric acid, aqueous
alkalies, and many other solvents.
Exposure to incompatible chemicals
may change fiber color and texture,
similar to a brownish smudge or
smear. Also, fibers will become less
elastic, with transverse cracks caused
by bending.
Poor
resistance.
Fiber strands
fuse together
and become
hard, brittle,
and shiny.
Generally offers good resistance.
However, paint can penetrate
into the weave and dry. This can
cause webbing to become hard
and brittle and can eventually
break the fibers. Some solvents
may affect fibers (see also
“Exposure to Chemicals”).
Poor protection
(no dielectric
strength).
Provides no
protection to
exposure to live
electrical lines or
equipment.
WARNING: Web strap should be replaced, regardless of condition, five (5) years after the hoist went into service.
HOIST LUBRICATION
Keep the ratchet gear, stopper ball, and turning area operating smoothly by regularly lubricating with a multi-purpose
lubricant. Wipe away any excess.
WARNING: Do NOT apply lubricant to the braking system.
TESTING
Hoists are tested by Klein Tools before being sold. However, hoists require operational testing if it has been altered,
repaired, or has been out of service for the last 12 months or more. Tests shall be performed by a designated person
and shall include:
• Checking all functions of the hoist while it is suspended in the unloaded state.
• After testing in the unloaded state, a load of at least 100 lbs (single line) and 200 lbs. (double line) shall be applied
to the hoist in order to check proper load control.
A hoist where load-suspension parts have been altered, replaced, or repaired shall be statically or dynamically load tested:
• The need for these tests shall be determined by a qualified person.
• A written report of the test should be prepared and placed on file.
• The test load shall not be less than 100% of the rated load of the hoist or more than 125% of the rated load of the
hoist unless otherwise recommended by the manufacturer or a qualified person.
• The replacement of the web strap is excluded from this load test, but should be tested in accordance with the
operational testing detailed above.
• Test anchorages or suspensions shall be approved by a qualified person.
WARRANTY AND REPAIRS
Klein web strap hoists and components, manufactured and sold for commercial or industrial uses, are warranted to
be free from defects in materials and workmanship for one year from the date of purchase. THERE ARE NO IMPLIED
WARRANTIES OF MERCHANTIBILITY OR FITNESS. At its option, Klein will repair or replace, or refund the purchase
price of, any product which fails to conform to this warranty under normal use and service. In no event shall Klein be
liable for incidental or consequential damage.
If your Klein product requires repair or for information on how to exercise your rights under the terms of this warranty,
please contact Klein Tools at 1-800-553-4676.
12
ENGLISH
Serial Number
Model
Capacity
DEFINITIONS
Abnormal operating conditions: Environmental conditions that are unfavorable, harmful, or detrimental to or for the
operation of a hoist, such as excessively high or low ambient temperatures, exposure to weather, corrosive fumes,
dust laden or moisture laden atmospheres, and hazardous locations.
Designated person: A person selected or assigned by the employer or the employer’s representative as being
competent to perform specific duties.
Heavy service: Service that involves operation within the rated load limit, which exceeds normal service.
Normal service: Distributed service that involves operation with randomly distributed loads within the rated load limit,
or uniform loads less than 65% of rated load for not more than 15% of the time.
Quali ed person: A person who, by possession of a recognized degree in an applicable field, or certificate of
professional standing, or who, by extensive knowledge, training, and experience, has successfully demonstrated the
ability to solve or resolve problems relating to the subject matter and work.
Severe service: Service that involves normal or heavy service with abnormal operating conditions.
CAUTION: WRONG DIRECTION
PRECAUCIÓN: DIRECCIÓN INCORRECTA
MISE EN GARDE: MAUVAIS SENS
Knob must be turned
counterclockwise when taking in strap
for the hoist to function correctly.
Para que el polipasto funcione
correctamente, se debe girar la perilla
en sentido contrario a las agujas del
reloj al recoger la correa.
La poignée doit être tournée dans
le sens antihoraire au moment
d’enrouler la courroie pour que le
palan fonctionne correctement.
1370486 Rev. 12/17 A
Loading...