• This protective headwear is designed to absorb some of the
energy of a blow through partial destruction of its component parts
and, even though damage may not be readily apparent, any
protective headwear subjected to severe impact should be replaced.
• This protective headwear must not be painted or cleaned with
solvents. Any decals applied to the protective headwear must be
compatible with the surface material and known not to affect
adversely the characteristics of the materials used in the protective
headwear. • Any addition or structural modification may reduce the
protective properties afforded by this protective headwear.
WARNING! BEFORE USE: READ ALL
INSTRUCTIONS OR RISK SERIOUS INJURY OR
DEATH. DO NOT REMOVE LABEL.
• Esta gorra de protección está diseñada para absorber parte de la energía
de un golpe a través de la destrucción parcial de sus componentes y,
aunque el daño no sea aparente, debe reemplazarse cualquier gorro de
protección que tenga un impacto severo. • Esta gorra de protección no
debe pintarse ni limpiarse con disolventes. Las calcomanías aplicadas a los
sombreros protectores deben ser compatibles con el material de la
superficie y se sabe que no afectan adversamente las características de los
materiales utilizados en los sombreros protectores.
• Cualquier adición o modificación estructural puede reducir las propiedades
protectoras proporcionadas por esta protección para la cabeza.
ADVERTENCIA! ANTES DE USAR: LEA TODAS LAS
INSTRUCCIONES O PELIGRO DE LESIONES GRAVES O LA
MUERTE. NO QUITE LA ETIQUETA.
• Ce casque de sécurité est conçu pour absorber une partie du choc
produit par un coup par la destruction partielle de ses composants. Même
si l'endommagement n'est pas visible, tout casque de sécurité qui a subi
un choc sévère devrait être remplacé. • Ce casque de sécurité ne doit
pas être peint ni nettoyé à l'aide de solvants. Toute décalcomanie
appliquée à ce casque doit être compatible avec le matériau de la calotte
et être reconnue inoffensive pour les matériaux entrant dans la
fabrication du casque. • Tout ajout au casque ou toute modification
structurale du casque peut en réduire les propriétés de protection.
ATTENTION. AVANT UTILISATION: LIRE TOUTES LES
INSTRUCTIONS OU RISQUE DE BLESSURES GRAVES OU DE
MORT. NE PAS ENLEVER L'ÉTIQUETTE.
1370537 Rev. 01/19 E
Models / Modelos / Modèles :
• This protective headwear is designed to absorb some of the
energy of a blow through partial destruction of its component parts
and, even though damage may not be readily apparent, any
protective headwear subjected to severe impact should be replaced.
• This protective headwear must not be painted or cleaned with
solvents.Any decals applied to the protective headwear must be
compatible with the surface material and known not to affect
adversely the characteristics of the materials used in the protective
headwear. • Any addition or structural modification may reduce the
protective properties afforded by this protective headwear.
WARNING! BEFORE USE: READ ALL
INSTRUCTIONS OR RISK SERIOUS INJURY OR
DEATH. DO NOT REMOVE LABEL.
• Esta gorra de protección está diseñada para absorber parte de la energía
de un golpe a través de la destrucción parcial de sus componentes y,
aunque el daño no sea aparente, debe reemplazarse cualquier gorro de
protección que tenga un impacto severo. • Esta gorra de protección no
debe pintarse ni limpiarse con disolventes. Las calcomanías aplicadas a los
sombreros protectores deben ser compatibles con el material de la
superficie y se sabe que no afectan adversamente las características de los
materiales utilizados en los sombreros protectores.
• Cualquier adición o modificación estructural puede reducir las propiedades
protectoras proporcionadas por esta protección para la cabeza.
ADVERTENCIA! ANTES DE USAR: LEA TODAS LAS
INSTRUCCIONES O PELIGRO DE LESIONES GRAVES O LA
MUERTE. NO QUITE LA ETIQUETA.
• Ce casque de sécurité est conçu pour absorber une partie du choc
produit par un coup par la destruction partielle de ses composants. Même
si l'endommagement n'est pas visible, tout casque de sécurité qui a subi
un choc sévère devrait être remplacé. • Ce casque de sécurité ne doit
pas être peint ni nettoyé à l'aide de solvants. Toute décalcomanie
appliquée à ce casque doit être compatible avec le matériau de la calotte
et être reconnue inoffensive pour les matériaux entrant dans la
fabrication du casque. • Tout ajout au casque ou toute modification
structurale du casque peut en réduire les propriétés de protection.
ATTENTION. AVANT UTILISATION: LIRE TOUTES LES
INSTRUCTIONS OU RISQUE DE BLESSURES GRAVES OU DE
MORT. NE PAS ENLEVER L'ÉTIQUETTE.
1370537 Rev. 01/19 E
1212
23
23
60345, 60346, 60347
Instructions for KARBNTM Full-Brim Hard Hat
60345
60347
60346
FIG. C
FIG. F
6
TM
5
9
11
12
15
FIG. G
20
21
19
7
FIG. A
FIG. B
1
2 3
14 13
FIG. D
8
10
22
23
64°
4
FIG. E
16
17
18
FIG. H
24
25
26
27
4
NOTE: This label is representative; contents will vary based on model #.
NOTA: esta etiqueta es representativa; los contenidos variarán según el n.º del modelo #.
REMARQUE: Cette étiquette est fournie à titre indicatif; son contenu varie en fonction du modèle #.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
28
1390419WEB Rev 09/20 A
ENGLISH
GENERAL SPECIFICATIONS
• Shell material: PC/ABS composite
• Surface pattern: Polymer Hydro-dipped film
• Standards: Klein Tools Karbn
ISEA Z89.1-2014, CSA Z94.1-15:
• Class E non-vented hard hats have been tested up to 20kV.
EN397:2012+A1:2012 (Clauses listed only):
• 5.2.4-Lateral Deformation (LD)
EN12492:2012 (Listed clauses only):
• 4.2.1.2-Front Energy Absorption Capacity
• 4.2.1.3-Side Energy Absorption Capacity
• 4.2.1.4-Rear Energy Absorption Capacity
FRONT:
EN12492
• Fits: Head Sizes 6-1/2 to 8 (20-1/2 to 25 inches / 52 to 64 cm)
SYMBOLS ON PRODUCT (FIG. A)
Reverse donning logo
1
Compliant Standards, Class, Type, and Head Size information
2
Recycling Code and material type
3
Date of manufacture
4
There are two warning labels affixed to the inside of this hard hat.
understand, and follow these instructions to ensure safe operation.
DO NOT REMOVE THESE LABELS.
WARNING LABELS (FIG. B)
TM
hard hats comply with Type I ANSI/
TOP: Z89.1/Z94.1
BACK: EN12492
SIDES: EN12492
DEFORMATION: EN397
SUSPENSION AND OPTIONAL CHIN STRAP: Must be replaced after no
more than 12 months of use.
ENTIRE HARD HAT: Entire Hard Hat must be replaced after no more
than 2 years of regular use, or 5 years from the date of manufacture,
whichever comes first.
These are MAXIMUM useful service life guidelines. Regular inspection
as detailed in the MAINTENANCE section above MUST be performed,
and may result in possible earlier replacement.
NOTE: This replacement schedule is a guideline that assumes
normal use and storage conditions for the hard hat. If the hard
hat is exposed to temperature extremes, persistent sunlight, or
chemicals, replacement may be required in a shorter time frame.
ACCESSORIES AND REPLACEMENT PARTS
Klein Tools hard hat accessories and replacement parts are
available online or at major distributors:
• KHHSPN2: Premium Replacement Suspension
• KHHSWTBND2: Premium Sweatband (3-pack)
• KHHTOPPAD2: Premium Top Comfort Pad (3-pack)
• KHHSTRP: Chin Strap
• 56048: Rechargeable Auto-Off Headlamp (Spot/Flood/All-On)
• 56049: Rechargeable Light Array Headlamp (Flood only)
• 56062: Rechargeable Headlamp / Magnetic Work Light (Spot/Flood)
NOTE: KLEIN TOOLS CANNOT GUARANTEE THAT THIRD-PARTY
ACCESSORIES WILL PERFORM OR FIT OPTIMALLY WITH
KLEIN TOOLS HARD HATS.
Do not place hard hat or its accessories in the trash. Items
must be properly disposed of in accordance with local
Read,
regulations. See www.epa.gov for additional information.
WARNINGS
READ ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE WARNINGS AND
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY OR DEATH.
• This hard hat provides LIMITED protection from small objects striking
top, front, back, left and right sides of the hard hat. This is NOT an
ANSI/CSA Type II hard hat.
• DO NOT expose suspension and padding to open flame.
• ELECTRICAL WARNING: Avoid areas where the chance of electrical
shock exists. Non-vented versions meet Class E requirements by
providing limited electrical protection. Class C vented models provide
NO electrical protection.
• If the hard hat has sustained an impact, dispose of it IMMEDIATELY,
even if damage is not visible.
• NEVER alter, puncture, modify or engrave the shell or the suspension.
• DO NOT use paints, solvents, chemicals, adhesives, gasoline or like
substances on this hard hat – doing so can lessen the protection
offered against impact and penetration.
• DO NOT use this hard hat as a vehicular or recreational hard hat.
• DO NOT
store objects between the suspension and the shell, as the
hard hat will not function as intended and can lessen the protection from
impact and penetration.
• Exposure to direct sunlight, corrosive environments, and/or extreme
temperatures below -40°F (-40°C) or above 120°F (49°C) can lessen
the ability of the hard hat to withstand impact and penetration.
MAINTENANCE
HARD HAT CLEANING AND STORAGE
• Clean the hard hat and suspension with mild soap and water only.
Rinse and wipe dry. Clean optional chin strap with damp cloth only.
Store in a cool place.
• See SWEATBAND AND TOP COMFORT PAD section of the operating
instructions (on other side) for additional maintenance information.
INSPECTION AND REPLACEMENT
Inspect the hard hat, including the suspension and shell, before and
after each use:
• Check the Hard Hat’s shell for any cracks, breakage, discoloration,
chalky appearance, or any other damage, excessive wear or unusual
condition. These conditions may indicate reduced impact or penetration
resistance and the Hard Hat must be replaced IMMEDIATELY.
• The suspension and optional chin strap should be checked for cracks,
breaks, damaged stitching or any other damage, excessive wear or
unusual condition. If any of these conditions exist, the suspension
and optional chin strap must be replaced IMMEDIATELY.
• Always use genuine Klein Tools replacement parts. This product
works as a system, and use of unauthorized suspensions may
reduce the protection you receive from this hard hat.
Find Quality Products Online at: sales@GlobalTestSupply.com
Universal accessory slots12Washable sweatband
5
Klein Tools accessory slots13Washable top comfort pad
6
Vents with shutter
7
(C-Class only)
Pivot adjustment
8
Size adjustment knob
9
Rear neck pad
10
Suspension strap
11
anchor slots
All hard hats come with suspension pre-installed at factory settings. The
suspension can be adjusted to ensure proper and secure fit to your head
for maximum protection. Follow the steps below:
STEP 1: Turn the size adjustment knob
the fit. Position the rear pad on the back of your head, closer to the neck.
Dress any bandanna knots or ponytails over the rear neck pad 10.
STEP 2: Tighten by turning the
until the hard hat is comfortable and snug. Move your head up,
down and side-to-side gently, like you would normally, and make
sure the hard hat stays on. Make sure that the hard hat is not
angled forward or backward, but rests level on your head.
If the hard hat does not fit properly at the factory settings, you
can further adjust the fit:
STEP 1: Free the suspension by turning the suspension bracket
16
approximately 90 degrees to free the bracket key17 from the
bracket key slots.
STEP 2: Determine which slot
the bracket slots deeper in the hard hat will move it higher on
the head and vice versa. Insert the bracket key17 and turn the
bracket16 approximately 90 degrees to lock into place. Always
match the settings on the left and right sides to prevent the
suspension from sitting at an angle.
STEP 3: Verify the hard hat fits properly. Follow the steps in the
FITTING section to ensure proper fit. Ensure that accessories
you plan to use fit and function properly while maintaining the
hard hat’s ability to perform its function optimally. Check with a
qualified safety expert, if unsure.
NOTE: The suspension strap lengths are xed and cannot be
adjusted. DO NOT attempt to alter.
www.GlobalTestSupply.com
USEFUL LIFE
DISPOSAL / RECYCLE
OPERATING INSTRUCTIONS
SEE OTHER SIDE.
FEATURE DETAILS (FIG.C)
Suspension straps
14
Re ective stickers
15
Suspension bracket
16
Bracket key
17
Bracket key slots
18
FITTING (FIG. D)
9
counterclockwise to loosen
size adjustment knob
ADJUSTMENTS (FIG. E)
18
you want to reattach to. Using
9
clockwise
SUSPENSION REPLACEMENT (FIG. F)
STEP 1: Place your forefinger under the strap anchor, and your
thumb over the anchor slot11. Push up with forefinger using
enough force to release the anchor from the slot. Do this for all
anchor slots (4 total).
straps to free the anchor. This could permanently damage the
straps, preventing them from performing as intended.
STEP 2: Make any height adjustments on the new suspension
before installation.
STEP 3: Push down each anchor until a click is heard and the
anchor cannot be pushed down any further. Do this for all 4
anchors.
NOTE: DO NOT use sharp tools that may damage the
anchors, or pull on the straps to secure the anchors.
STEP 4: Check proper installation by pushing up on all 4 anchor
bases. The anchors should remain fully seated in their slots. If
not, repeat STEP 3.
STEP 5: Verify the hard hat fits properly. Follow the steps in
the FITTING section to ensure proper fit. Also ensure that
accessories you plan to use fit and function properly while
maintaining the hard hat’s ability to perform optimally.
NOTE: DO NOT pull on the suspension
SWEATBAND AND TOP COMFORT PAD (FIG.H)
Klein Tools Karbn
and top comfort pad made of evaporative material designed not
only to wick away sweat, but to also enhance cooling. Simply take
the sweatband or top pad and wet, shake to remove all excess
water and install for extended periods of cooling. Both are machine
washable in a normal wash cycle. Do NOT wash with bleach or
with detergents containing bleach. Machine dry on normal or low
heat setting only.
The sweatband and top comfort pad can be easily removed and
reinstalled on the suspension:
• The top comfort pad is held in place by a single hook-and-loop
27
pad
• The sweatband is held in place by four suspension hooks
three hook-and-loop pads
simply detach all hook-and-loop pads and slide the sweatband
off the suspension hooks.
TM
hard hats come with an advanced sweatband
.
27
,
on the side and front. To remove,
28
and
VENTS (C-CLASS ONLY)
Klein Tools Class C hard hats have vents and shutters on both
sides. The vents can be adjusted by simply sliding the shutter
7
tabs
up or down.
The vents and shutters will NOT prevent vapors, liquids, or
debris smaller than the vents from entering the hard hat.
56048 HEADLAMP (FIG.G)
Klein Tools’ 56048 Rechargeable Headlamp provides three
modes: 22-hour floodlight; 12-hour focused spotlight, 400
lumen All-On mode. 56048 features an LED battery gauge that
indicates remaining battery life, and an auto-off sensor that turns
off the headlamp in bright light or outdoors where additional
headlamp lighting is not needed, to extend battery life.
Release tab
19
On/Off/Mode button
20
Spot light
21
Flood lights
22
The 56048 can be attached to both the front or back of the hard hat via
the Klein Tools accessory slot. It can be tilted up to 64 degrees on the
hard hat and stand alone as a work light.
To install the headlamp onto a Klein hard hat, align the pivoting mount
24
with the Klein Tools accessory slot6 on the hard hat and
push down until the headlamp clicks securely into place.
To remove the headlamp, press forward on the Release Tab
and lift the headlamp out of the accessory slot.
Bracket
23
Pivoting mount
24
Charging port cover
25
Light sensor
26
19
REFLECTIVE STICKERS (FIG. C)
Klein Tools Karbn
These have been tested and found compatible with this hard hat.
WARNING: Klein Tools DOES NOT approve the application of
stickers, hot stamps, inks, and foils that have metallic content
to this hard hat by end users. Such modi cations can alter the
performance of the hard hat.
TM
hard hats come with reflective stickers15 installed.
,
Loading...