Kleenmaid ZSGS420IBS User Manual

Monogram.

®

Installation
Instructions

Side by Side Refrigerators

Models
ZSGS420D
ZSGW420D
ZSGB420D

Design Guide
With Installation Instructions

Safety Information

Skill Level — Installation of this refrigerator

requires basic mechanical, electrical, carpentry
and plumbing skills. Proper installation is the
responsibility of the installer. Product failure due
to improper installation is not covered under the
Warranty.

WARNING:

• These refrigerators are top-heavy and must be
secured to prevent the possibility of tipping
forward. Anti-Tip protection is required.
See page 12 for details.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric service cords
that become frayed or damaged.

• Unplug the refrigerator before cleaning or making
repairs.

• Repairs should be made by a qualified service
technician.

AVERTISSEMENT

• Ces réfrigérateurs sont lourds en haut et il faut les
arrimer pour éviter leur basculement. Il faut avoir
un système de protection contre le renversement.
Voir les détails page 12.

• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.

• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.

• Il faut débrancher le réfrigérateur avant le
nettoyage ou toute intervention.

• Les réparations doivent être faites par un
technicien qualifié.

2

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT— Save these instructions

for local inspector’s use. Observe all governing codes
and ordinances.

• Note to Installer — Be sure to leave these
instructions with the Consumer.

• Note to Consumer — Keep these instructions
with your Owner’s Manual for future reference.

WARNING:

This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 10.

AVERTISSEMENT

Cet appareil doit être correctement mis à la terre.
Consulter « Mise à la terre du réfrigérateur », page 10.

If you received a damaged refrigerator, you should
immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to
the product – FOUR PEOPLE ARE REQUIRED FOR
INSTALLATION OF THIS REFRIGERATOR.

PRUDENCE

À cause du poids et de la taille de ce réfrigérator et
pour réduire le risque de blessure et de dommages.
IL FAUT QUATRE PERSONNES POUR
L’INSTALLATION DE CE RÉFRIGÉRATEUR.

CONTENTS

Planning Guide

The Installation Space ....................................3

Dimensions and Clearances ..........................3

130° Door Swing ..............................................4

90° Door Swing ................................................5

Customization Basics ......................................6

6 mm Framed Panel Dimensions ..................7

19 mm Overlay Panel Dimensions ................8

Raised Overlay Panel Design ........................9

Side Panels......................................................10

Installation Instructions

Tools, Hardware, Materials ........................10

Grounding the Refrigerator ..........................10

Step 1, Remove Packaging ..........................11

Step 2, Install Water Line ............................11

Step 2A, RO Water Line ................................12

Step 3, Install Side Panels ..........................12

Step 4, Install Anti-Tip Brackets ................12

Step 5, Open Grille Panel,

Connect Power ................................13

Step 6, Level Refrigerator ............................13

Step 7, Secure Refrigerator to Cabinetry ..14

Step 8, Adjust Door Swing ..........................14

Step 9, Install Grille Panel ............................14

Step 10, Install Framed Panels ....................15

Step 10A, Install Overlay Panels ................16

Step 11, Install Dispenser Trim ....................17

Step 12, Connect Water Supply ..................17

Step 13, Connect Power ..............................18

Step 14, Start Icemaker ................................18

Step 15, Install Toekick ................................18

*2134 mm
From Floor to
Top Frame

645 mm Framed Models
654 mm Stainless Steel Models
Case Depth

Depth Including Handles:
683 mm Framed Models
705 mm Stainless Steel Models

1067 mm

Frame to Frame

1041 mm

Case Width

*2121 mm

at

Rear

606 mm

Behind

Frame

676 mm

102 mm Min.

to Wall

102 mm Min.

to Wall

483 mm

330 mm

Design Guide

THE INSTALLATION SPACE

Water And Electrical Locations

The opening must be prepared with the electrical
and water supply located as shown.

The cutout depth must be 610 mm

The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot
exceed the 610 mm installation depth shown. The
top case trim overlaps the bottom of the soffit.

Additional Specifications

• 220 volt, 50 Hz., 4.5 amps power supply is required.
An individual properly earthed branch circuit or
circuit breaker is recommended. Install a properly
earthed electrical receptacle recessed into the back
wall. Electrical outlet must be located on rear wall as
shown.

• Water line can enter the opening through the floor

or back wall. The water line should be 1/4" O.D.
copper tubing or GE SmartConnect™kit between
the cold water line and water connection location,
long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut off valve in the water line is required.

DIMENSIONS AND CLEARANCES

Product Clearances

These refrigerators are equipped with a 2 position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets or
walls is restricted.

3

*The finished cutout width must be 1054 mm.

90° Door Swing130° Door Swing

*Finished Width

152 mm

127 mm

Electrical
Area

2146 mm max

2121 mm min

Finished
Opening

1905 mm From Floor

to Bottom

of Electrical

Area

610 mm

127 mm

127 mm

Water Supply

89 mm

457 mm

89 mm

Allow minimum clearances for freezer door, 330 mm
and fresh food door, 483 mm for a full 130° door
swing and to allow for pan removal.

102 mm minimum clearance is required when door
swing is adjusted to 90°. If the 90° door stop position
is used, pan access is maintained, but pan removal is
restricted.

See illustrations pages 4 and 5 to determine door
swing interaction with adjacent cabinets or
countertops.

* Shipping height.

The refrigerator can
be adjusted to fit
into a cutout that
is 2121 min. to 2146
mm max. height.
Note that the top
case trim at the
front is 13 mm
higher and will
overlap upper
cabinetry or soffit.
Use leveling legs
and wheels for a
maximum 25 mm
height adjustment.

6 mm

13 mm

19 mm

25 mm

32 mm

25 mm

19 mm Overlay

Panel

(Nominal Size)

6 mm

13 mm

19 mm

51 mm

32 mm

38 mm

44 mm

76 mm

57 mm

64 mm

70 mm

6 mm

13 mm

19 mm

Door

6060 mm From

Rear of

Refrigerator

25 mm

Refrigerator

Case
Trim

Design Guide

Top View
130° DOOR SWING
(factory setting)
Scale 1:1

IMPORTANT NOTE—FOR DISPENSER MODELS:

Dispenser models are supplied with 2 dispenser
trims, one to fit framed panels and one for
overlay panels. Dispenser trim fit to the custom

panel depends on correct panel thickness.

Framed panels must be 6 mm nominal. Overlay
panels should be constructed as shown to
accomplish a total 28 mm thickness. See pages
7 and 8 for details.

4

Frameless Cabinets: The case trim overlaps
cabinets at the top and sides. Therefore,
frameless cabinets may require filler strips to
prevent interference with cabinet door swing.
The opening must allow for filler strips.

6 mm

13 mm

19 mm

25 mm

32 mm

6 mm

13 mm

19 mm

25 mm

32 mm

38 mm

606 mm

From Rear of

Refrigerator

19 mm Overlay

Panel

(Nominal Size)

Case Trim

Refrigerator

Door

Design Guide

5

Top View
90° DOOR SWING
(optional setting)
Scale 1:1

IMPORTANT NOTE—FOR DISPENSER
MODELS: Dispenser models are

supplied with 2 dispenser trims,
one to fit framed panels and one for
overlay panels. Dispenser trim fit to

the custom panel depends on correct
panel thickness. Framed panels must

be 6 mm nominal. Overlay panels
should be constructed as shown to
accomplish a total 28 mm thickness.
See pages 7 and 8 for details.

Frameless Cabinets:

The case trim overlaps
cabinets at the top and
sides. Therefore, frameless
cabinets may require
filler strips to prevent
interference with cabinet
door swing. The opening
must allow for filler strips.

Standard Door Handles

19 mm Overlay Panel
3 mm Thick Spacer Panel
6 mm Thick Backer Panel

Design Guide

CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits

Overlay panels

You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetry.

Standard supplied handles shown in 19 mm overlay panel position.

Stainless Steel Wrapped Models

42" wide models – ZSGS420D

Trimmed Models

42" wide models – ZSGW420D, ZSGB420D

Stainless Steel Wrapped Refrigerators

Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.

Framed panels

You may install 6 mm thick custom panels from your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels from your Monogram
dealer.

6

Standard supplied handles shown in 6 mm panel position.

Door Handles

The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you
may order ZKHSS2 Monogram stainless steel tubular
handle kit for 19 mm overlay panels.

Side Panels

Side panels must be used whenever the sides of the
refrigerator will be exposed.

Optional Accessory Kits

ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 19 mm overlay panels.

Accessory Panels

White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut
to size and ready to install.

Models White Black Stainless

Acrylic Acrylic Steel

ZSGW420D ZPW420D ZPS420D
ZSGB420D ZPB420D ZPS420D

Framed Panel

Standard Door Handles