Kleenmaid MT301 User Manual
SURNAME NAME
ADRESS
MODEL
DATE
info@kleenmaid.com
Using instructions
Apparecchio conforme alle direttive CEE
MT 301
MT 401
User instructions
1) periodically clean the aerator filter;
2) install filter valves under the sink and periodically clean the
filters;
3) DO NOT USE DETERGENTS, SOLVENTS, CHEMICAL
AGENTS, ABRASIVE SPONGES, WIRE WOOL OR
ALCOHOL, ETC., which would irreparably damage the
surface of the product and ruin its appearance, sheen and
matt finishes;
4) CLEAN WITH SOAPY WATER AND DRY WITH A SOFT
CLOTH;
5) dry the product after use if the water is very hard or
aggressive, as it may leave deposits which would damage
the surface;
6) do not install the tap when the water pressure exceeds 5
bar (in this case, an adapter is required);
7) Rinse the water pipes before installing the tap.
REV. 11/2007
2
3
4
5
6
1
11
MT301 Mounting and plumbing connection
- Turn off water supply
- Drill 35 mm. hole in bench top or stainless steel sink
- Place rubber seal item 1 into the recess of the bottom of the tap body or
collar if applicable
- Screw inlet hoses item 11 into body of tap ensuring hot and cold hoses are
inserted into the correct ports
- Place the hoses thru the hold in the bench top of the sink and position the
tap
- Place item 3 (rubber seal) over the mounting bolt and 2 against the underside
of bench or sink
- Place plastic supporting collar item 4 over the mounting bolt 2 and against
the underside of bench or sink (note flat triangle side of plastic collar should be
against the bench or sink)
- Place metal mounting bracket item 5 over mounting bolt 2 and screw on
securing nut item 6 and tighten metal bracket against the underside of bench
or sink
- Position tap and securely tighten fixing nut
- Connect inlet hoses item 11, ensuring the sealing washers are in place to the
correct hot and cold water taps
- Turn on water supply
- Check tap for operation and test for leaks.
1
2
3
5
4
6
7
8
11
9
10
MT401 Mounting and plumbing connection
- Turn off water supply
- Feed nylon hose thru the body of the tap (from top to bottom)
- Connect shower head to nylon hose with the rubber seal supplied and tighten
- Drill 35 mm. hole in bench top or stainless steel sink
- Place rubber seal item 1 into the recess of the bottom of the tap body or collar
if applicable
- Place the hoses thru the hold in the bench top of the sink and position the
tap
- Place item 3 (rubber seal) over the mounting bolt 2 and against the underside
of bench or sink
- Place plastic supporting collar item 4 over the mounting 2 bolt and against
the underside of bench or sink (note flat triangle side of plastic collar should be
against the bench or sink)
- Place metal mounting bracket item 5 over mounting bolt 2 and screw on
securing nut Item 6 and tighten metal bracket against the underside of bench or
sink
- Install non-return valve item 7 to the inlet which is located on the tap mounting bolt (ensure rubber and fibre washer are inserted into the non-return valve)
- Connect nylon hose to non return valve using rubber seal provided and
tighten
- Position tap and securely tighten fixing nut
- Attach counterweight item 9 to the nylon hose 8 using screw item 10 in such
a way that it provides downward pressure to allow easy retraction of the pull out
shower head. Note: the counterweight should not touch the bottom of the cabinet
until the hose is fully retracted.
- Connect inlet hoses item 11, ensuring the sealing washers are in place to the
correct hot and cold water taps
- Turn on water supply
- Check tap for operation and test for leaks.
MT 301 MT 401
Loading...