Kleenmaid KFL1600 User Manual
Instructions for Use
Washing machine
KFL1600
Thank you for your confi dence in purchasing our washing machine, and
congratulations on the excellent choice.
Your new washing machine meets the requirements of modern treatment of
laundry. It is rational in the consumption of energy, water and washing agents.
Our appliances are friendly to the environment. Some of the materials may be
recycled, others deposited or decomposed. To avoid pollution of environment,
once your appliance is no longer useful, take it to your local authorised waste
appliance dealer.
The appliance is intended exclusively for use in households. If the appliance is
used for professional purposes, for profi t, or for purposes beyond regular use
in a household, or if appliance is used by a person who is not a consumer, the
warranty period equals the shortest warranty period possible as stipulated by
the relevant legislation.
130715
Description of washing machine .....................3
Cautions ............................................................. 4
Installation and connection .............................. 6
Operation.......................................................... 10
Tips for washing and energy saving .............23
Cleaning and maintenance ............................. 25
Failures ............................................................. 28
Tables ............................................................... 31
2
Description of washing machine
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
Technical information
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
Model (KFL1600)
Dimensions (w x d x h):
600 mm x 600 mm x 850 mm
Depth with door open: 106 cm
Weight (net): 92 kg
Nominal voltage: 240 V, 50 Hz
Power: 2300 W
Max. load: 6,5 kg
Power socket: (240 V, 50 Hz, 10 A)
Water pressure:
min. 0,05 MPa, max. 0,8 MPa
Fuse: 10 A
130715
3
Cautions
Be sure to remove transport brackets prior to fi rst use of the appliance.
•
Attempted operation of the blocked machine may result in irreparable
damage which is not covered by the manufacturer’s warranty!
When connecting your washing machine to water supply, be sure to use
•
brand new water inlet hose and appropriate sealing gaskets (attached).
Do not locate the machine in a room with temperature below 0°C. Parts of the
•
machine may be damaged if frozen.
Install the washing machine in a perfectly horizontal position, on solid fl at
•
concrete fl oor.
Follow the instructions for correct installation and water and mains
•
connections.
Never immerse the end of the drain hose into the draining water.
•
Prior to starting the washing cycle lock the door by pressing at the designed
•
spot.
Door may not be opened during the washing cycle.
•
Use only detergents and softeners for machine wash. Manufacturer may not
•
assume responsibility for any damage and eventual discoloring of gaskets
and plastic components as a consequence of incorrect use of bleach and/or
colouring agents.
For removal of lime residues use such agents with added anti-corrosion
•
agents. Follow the manufacturer’s instructions. Finish the lime removal by
multiple rinsing to remove completely eventual acid residues.
Never use detergents containing solvents, as there is a danger of creating
•
toxic gasses which may damage the machine and result in ignition or
explosion.
Upon completion of washing operation close the water tap.
•
Before any transport block the machine by inserting at least one transport
•
blocking rod. Prior to this operation disconnect the appliance from the mains
power!
Rating plate with basic information is located above the opening of the
•
machine.
The warranty shall not apply to consumables (bulbs), minor discoloration or
•
deviations of color, increased noise level as a consequence of appliance age,
which does not affect appliance functionality, and aesthetical defi ciencies
which do not affect appliance functionality or safety.
130715
4
The belt can be replaced by a servicing
engineer only, who incorporates an
original spare part with the marking MIG
OPTIBELT 6EPJ 1260, code 111622 or 6EPJ
1278 code 587612.
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste.
Instead it shall be handed over to the
applicable collection point for the recycling
of electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of thisproduct. For more detailed
information about recycling of this product,
please contact your local city offi ce, your
household waste disposal service or the
shop where you purchased the product.
This appliance is not intended for use by
young children or infi rm persons unless
they have been adequately supervised by a
responsible person to ensure that they can
use the appliance safely.
Young children should be supervised
to ensure that they do not play with the
appliance.
130715
5
Installation and connection
Package removal
Removal of transport
brackets
In removing the wrapping be careful not to
damage the appliance with a sharp object.
Before connecting the appliance, let it
warm up to room temperature (wait for two
hours).
Our appliances are packed in environmentally
•
friendly materials which may be recycled,
deposited or decomposed without any threat to
the environment.
To this end all wrappings are marked accordingly.
•
Move the hoses.
•
Loosen screws A at the rear of the machine
•
(Fig. 1).
Remove the brackets B (Fig. 1) and slide them
•
into the groove on the blocking rod (Fig. 2) - the
right one should be turned around.
Use the brackets to rotate blocking rods for 90°
•
and pull them out.
Close the openings with attached plastic pegs.
•
Save transport brackets for eventual later use.
Be sure to remove the transport brackets
prior fi rst use, otherwise the appliance
may be permanently damaged. In such
cases the warranty conditions are void.
130715
Fig. 1 Fig. 2
6
Levelling the appliance
Put the appliance in a horizontal position by
•
turning the adjustable legs.
The legs are adjustable up to +/- 1 cm.
After the adjustment tighten the nuts fi rmly (A)
- towards the bottom of the machine!
Vibrations, moving of the appliance and
loud operation due to incorrect setting of
the adjustable feet shall not be covered by
this warranty.
The appliance should be placed on a
surface with concrete base; the surface
should be dry and clean in order to prevent
slipping. The adjustable feet should also be
cleaned before installation.
If you have a tumble dryer of the same
•
dimensions, you can place it on top of the
washing machine.
Water inlet connection
To ensure correct operation of the appliance,
water pressure inlet must be between 0,05
and 0,8 MPa.
Minimum water pressure can be established
by measuring the quantity of poured out
water. 3 litres of water must be poured out
from completely opened tap in 15 seconds.
Insert the gasket with screen into the water inlet
•
hose thread. Screw the hose thread to the water
faucet.
In case of hot and cold water connection, connect
•
one hose to cold and the other to hot water faucet
as marked at the rear of the appliance (letters C
and H) (C - cold; H - hot)
130715
7
Partial Aqua-stop (water stop system)
In case of damage to the interior hose, leaking is
prevented by an automatic closing system which
stops water inlet to the machine. In such cases
display A turns red.
Inlet hose must be replaced.
Water outlet connection
Connection to Power
Supply
130715
Fix the outlet hose to the wall drain outlet
•
(diameter min. 4 cm).
Wall drain must be installed properly and must
•
enable occasional cleaning.
Fasten the outlet hose support with a piece of
•
rope led through the hose elbow to prevent the
hose from slipping to the fl oor.
The end of the outlet hose should be
placedbetween minimum 60 cm and maximum
100 cmabove the fl oor level.
Connect the appliance to the power supply with the
cord provided.
A three pin, switched, earthed power point less than
1500 mm from the back of the machine is required.
Rated voltage, frequency and other data are listed
on the rating plate on the back of the machine.
Check that the supplied electrical voltage is the
same as on the rating sticker.
Your washing machine should be earthed and
connected to the power supply according to local
electricity supplier regulations and standards.
If the supply cord of this appliance is
damaged, it must be replaced by the special
cord, part no. G 360440, available from your
nearest spare parts centre (refer to guarantee
and service guide).
8
CAUTION: If this appliance is supplied
from a cord extension set or electrical
portable outlet device, the cord extension
set or electrical portable outlet device must
be positioned so that it is not subject to
splashing or ingress of moisture.
If the power circuit for the machine is earth leakage or
RCDprotected, it should be protected by a switch of 30mA. If
the protecting switch is less than 30mA the machine may be
switched off during normal operation.
130715
9
Operation
A - program selector
B - MENU knob
C - SELECTION knob
D - Quick
F - START/PAUSE knob
G - door knob (depending on the
model)
H - display
E - easy ironing knob
Program selector
Basic programs
Cotton
Intensive
Synthetics Conditioning
Delicate Drain
Wool Spin
Handl wash
Jogging
Mix
Partial programs
Rinse
Functional knobs
Knob B (MENU) - Use this knob to scroll around main menu.
Knob C (SELECTION) - Use this knob to select and customise additional
130715
functions.
Knob F (START/PAUSE) - Use it to start or interrupt the program.
10
Before fi rst use
- Selecting language
To change the language in which the information
appear on the display, press simultaneously the
key MENU (B) and SELECTION(C), and turn the
program selector (A) from position “0” to the fi rst
program in clockwise direction (Cotton 95°C). The
name of actually selected language appears on the
display.
Scroll down the selection of languages by pressing
the SELECTION knob (C), until you fi nd the desired
language. Then turn the program selector back to
position “0”. Last selected language will be saved
automatically.
Washing procedure
Open the door of the machine. Door is opened by
•
pressing the knob (G).
Sort the laundry by the type of fabrics
•
Load the laundry into the drum.
•
Close the door.
•
Open the water inlet tap.
•
Push the ON/OFF button and select the program
•
Add washing and treatment agents (detergent
•
and softener).
Start the operation by pushing the START knob
•
(F).
Do the buttons and zippers, tie strings and
pull out the pockets.
Very delicate laundry should be put in a
special protective laundry bag.
It is suggested to load the drum with items
of different sizes.
Pay attention to the labels on the clothes
which indicating the recommending
washing mode (see table of textile
treatment symbols on the last page of
these instructions).
130715
11
Loading...